Comfort Zone 18" 2 in 1 Performance Stand Fan

Features

• Patented 18 inches plastic grid and 6 blades.
• 2 in 1 fan: Stand and wall.
• 3 speeds.
• Adjustable stand up to 53.15 in height.
• Wide area oscillation.
• Adjustable tilt head.
• 120 V~ A.C. / 60Hz

Important Instructions

Read this user manual completely before assembling or starting to use your product.

Before connecting the fan to the power source, check whether the mains voltage is compatible with the one marked on the fan (120 V~).

Remove all packing material from the product.

Make sure that the fan is in the off position "0" before connecting to the power supply.

Safety Tips and Warnings

Please read carefully these instructions before putting together and starting to operate this product. Keep this instructions manual in a safe and well known place for future reference.

Keep this fan away from water. Do not use it either near the sink or any other liquid containers.

Please set your fan on a flat steady surface. Do not set this unit either on or near an electric or gas stoves.

WARNING: As any other electric powered fan, this one contains parts which drive electrical power while connected, even when the unit is turned off.

WARNING: ELECTRICAL SHOCK DANGER

• Use grounded outlet only.
• Do not use any external connections, adapters or timers.
• Do not overcharge the electrical power socket where you connect this household.
• Always set the fan on a dry, flat and steady surface.
• Do not handle this fan when having your hands wet.
• Before you connect the fan to the electrical power, make sure both the cord and the socket are completely dry.
• Do not submerge in water or any other liquid.
• DO NOT USE THE FAN IF IT FELL INTO WATER.

Important Safety Guidelines

• Avoid any contact with the moving parts of this fan. Keep your hair, hands and feet away from the moving parts of the "stand fan".
• Please keep this fan away from children or people with any mental or physical disability, as well as away from those people who have not received the proper instruction on the use of this fan.
• Please be aware of your children when the "stand fan" is in use. Do not allow children to play near the fan.
• Please make sure to unplug from the electrical power the fan every time you finish using it and before cleaning it. Make sure to use only a 120 Volts electric source.
• Do not use the "stand fan" if you detect any damage on the unit or the electrical power cord.
• Do not use the "stand fan" if the unit has fallen down and become damaged in any way. Please take the unit to your nearest authorized service center, so that it can be repaired, checked or adjusted.
• Do not let the "stand fan" to enter in contact with water or any liquid.
• Do not use this fan outside.
• Always set the "stand fan" on a plain, stable surface in order to avoid it to fall.
• Vacuum dust and residuals from the grid and the blades after unplugging the "stand fan".
• Do not operate the "stand fan" without the grids set.
• Make sure to turn off the fan whenever unattended. Always remember to unplug from the electric power supply. Never leave the fan unattended while plugged in.
• If the electrical connection, cord or plug are damaged, they must be repaired by the manufacturer directly or by someone from an authorized service center.
• Never use the fan if it is damaged in any way, either the unit itself or its cord and plug.
• Keep the electrical connection cord away from sharp edges, as well as away from the moving parts of the "stand fan".
• Do not use the fan if it has fallen down and any damage has been determined.
• Never set the fan on a wet floor and never mop around the fan itself when operating.
• This fan is not a toy, keep away from children.

Parts Identification

Parts Identification 1

A.- ST 3x8mm W/Washer Screw: This screw is used to fit the rear grill to the fan motor cover and is placed before putting the propeller on the motor shaft.

B & C.- M3x20 mm Screw and M3 Nut: They are used to adjust the front and rear grille, these are placed at the end of assembling the grilles. [Diagram: Figure A]

Parts Identification 2

• 1. Front grid
• 2. Back grid
• 3. Safety grid's fixing locks
• 4. Fan blades
• 5. Motor shaft
• 6. Blades nut
• 7. Engine body
• 8. Swing pivot
• 9. Manual operation (Speed/Off/Pilot Light)
• 10. Pilot light/Night light
• 11. Control panel
• 12. Telescopic tube
• 13. Height fixing rings
• 14. Fixing knob
• 15. Base
• 16. Counterweight
• 17. Washer
• 18. L screw
• 19. Wall support attachment

Assembly Instructions

Fan Assembly

Set the back grid on the motor shaft, make sure that the internal arrow (as drawn in the enhancement within Figure B) points up and the 4 central clips fit. You might push firmly in order to make them tightly fit. Once the 4 clips have been set, make sure they are tight. [Diagram: Figure C]

Take the 3x8 mm W/ Washer screw (A) from your kit and screw it with the help of a Phillips screwdriver over the cylinder-shaped housing that is seen at the top of the grill. [Diagram: Figure D]

Set the fan blades correctly on the engine body and screw the blades nut towards the word "THIGHTEN" as the arrows show. [Diagram: Figure E]

Join the front and back grills together by aligning the 6 fixing clips and push firmly until a "click" sound is heard. [Diagram: Figure F]

Take the M3mm nut (C) from your kit and place it on the hex socket at the bottom of the rear grille. [Diagram: Figure G]

Then take the M3x20 mm screw (B) from your kit and put it on the socket on the bottom of the front grille. With the help of a Phillips screwdriver, screw the nut to secure both racks. [Diagram: Figure H]

Mounting the Base

Unscrew the L screw from the telescopic tube washer. Set the tube inside the base's round space.

Set the counterweight at the bottom of the base. Set the washer under the counterweight so that the domed part keeps touching the counterweight. [Diagram: Figure I]

Screw clockwise the L screw into the washer hole holding the telescopic tube until it is firmly tight into the base. [Diagram: Figure J]

Stand Assembly

Screw the height fixing ring counter clockwise and lift the stand internal tube until it reaches the desired height. The maximum fan height is 53.15 in.

Screw the height fixing ring clockwise until it is safely tight in order to fix the fan's height.

Unscrew the fixing knob and fit the telescopic tube inside the engine body set (motor, blades and grids). Make sure to reach the bottom of the base and screw the fixing knob clockwise until it is firmly adjusted.

Assembling the Wall Support Attachment

By using a 1/4" drill (not included) make two holes horizontally aligned with 1.57 in of separation (it is not recommended to install the wall support attachment on prefabricated walls or not stable walls). [Diagram: Figures S1-S5]

Insert in every hole a 1/4" plastic dowel (included), then insert in each plastic dowel a 1/4" x 1" screw (included) no more than 2 cm deep (S1).

Set the previously assembled body with grids and blades on the wall support attachment (S2) and tighten it from behind with the fixing knob (S3).

Finally, set the display on the previously set wall screws (S4) and make sure it is properly set (S5).

Swing Pivot

The swing pivot may not be assembled to the engine body.

Find the swing pivot inside one of the plastic bags that contain parts of the fan. Introduce the pivot inside the engine body hole assigned for it and push down firmly until a "click" sound is heard and make sure the pivot is correctly assembled. [Diagram: Figure K]

Operation Mode

• Make sure to set the fan on a stable and firm surface; avoid rugs or carpets where it can tangle.
• Make sure the unit is properly plugged to the electric power supply, not before you verify the appliance is off.
• To start the fan, push the desired speed button: 1=Low; 2=Medium; 3=High.
• To refresh large rooms, our recommendation is to use oscillating mode by pulling the swing pivot upwards to start oscillation and pushing down again to stop it.
• The fan's head angle can be horizontally adjusted by pulling the swing pivot upwards so that it will move on a 150° oscillation range. You can set it to the desired position by pushing the pivot down.
• Make sure, before starting the operation of the fan, that it is set more than 3.94 in away from any object which may block the air flow, such as walls, curtains, or furniture.

ATTENTION: Make sure to turn off the fan by pushing the off button "0", before you decide to move it to another place.

Pilot Light / Night Light

The pilot light helps you locate the fan in the darkness. You turn it on by pushing the button "L" once, and turn it off by pushing the off button "0" once.

Cleaning and Maintenance

Remember to unplug the fan from the electric power supply every time after finishing using it.

To clean the fan exterior, make sure to use a dry cloth lightly wet with a soft liquid soap. Never submerge the fan in water or any other fluid, nor let any water leak into the inside of the fan. Avoid using either corrosive or flammable substances such as gasoline, thinner, etc., since this can damage the fan and produce toxic vapors.

We recommend to follow these steps in order to clean the blades:

1. Remove the front grid.
2. Clean the blades with a dry cloth lightly wet with a soft liquid soap.
3. Make sure to put back the safety grill's fixing locks and that these firmly hold both grills (front and back). Make sure the fan is completely dry before starting it again.

Storage

Make sure to turn the "stand fan" off. Make sure the blades of the "stand fan" are completely stopped.

Do not tangle the electric power cord around the appliance; roll it in circles without forcing it.

Store both appliances in a clean and dry space, and keep it always in a vertical position.

Fuse Replacement

This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.

1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on the cord.
2. Open fuse cover by sliding open the fuse access cover on top of the attachment plug towards the blades. [Diagram: Figure 2 - "Slide Cover to Open"]
3. Remove fuse carefully. Use a small tool to pry the end of the fuse from the holder cavity. Be careful not to break the glass window.
4. Replace fuse. WARNING: Risk of fire. Replace fuse only with an identical 2.5 or 5.0 Amp, 125 Volt fuse (3.6mm x 10mm).
5. Be sure fuse is properly seated within its cavity. Close fuse cover by sliding it back to its original closed position.

Limited Warranty

This unit is guaranteed to the original retail purchaser against defects in quality or workmanship for a period of one year from the date of original purchase. If this unit fails because of a manufacturing defect within 30 days of purchase, return the unit, with your receipt, to the retailer. After 30 days, but within the warranty period, if the unit was purchased within the continental United States, return it, freight prepaid, to World and Main for repair or replacement. If the unit was purchased outside the continental United States, return the unit to the place of purchase.

This warranty does not cover damage caused by misuse, abuse, overheating or alteration. Repairs made by anyone other than World and Main are not covered in this warranty. World and Main will not be held liable for any losses due to neglectful operation.

All implied warranties, including the warranties of merchantability and of fitness of purpose, if applicable, are hereby limited in duration to the period of one year from the date of original retail purchase. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

Incidental or consequential damages arising from a breach of either express or implied warranties are hereby disclaimed and excluded. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.

Upon the expiration of this warranty, all such liability will terminate. No other warranties are expressed or implied.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. No informal dispute settlement mechanisms are available. This limited warranty is given in lieu of all other warranties.