User Manual for TFIRETEK models including: 2A54Y-X3PRO, 2A54YX3PRO, x3pro, X3PRO Projector, X3PRO, Projector
Shenzhen TFIRETEK Technology Co., Ltd. X3PRO Projector 2A54Y-X3PRO 2A54YX3PRO x3pro
File Info : application/pdf, 1 Pages, 1.71MB
DocumentDocument70X100mm 105g Safety Tips 1 Safety Tips 2 Specif ications Projection Technology Lamp Type X3 Pro LCD Display LED Lamp 2.4GHz&5GHz; IEEE 802.11 a/b/g/n/ac LAN Type-C 3.5mm audio port LAN IN*1 USB-C port 3 3 Projector Introduction 1 2 4 56 7 8 9 10 3 576 3 11 1.IR Remote Sensor 2.Projection Lens 3.Dust Filter 4.LAN Port 5.IR Remote Sensor 6.3.5mm Audio Port 7.USB Port 8.HD Port 9.Type C Port 10.AC Port 11.Vent 1 9 10 12 2 8 4 1.Power On 2.Signal Source 3.Ok(Enter) 4.Down 5.Left 6.Right 11 7.Up 8.Menu 9.Return 10.Projector Foot Pad 11.Projector Mounting Hole 12.Dust Removal Hole 4 Remote Control Introduction Power ON/OFF Navigation key Return Home VOL FocusVoice Key Input Source Menu Mouse Mode Setting VOL + Focus+ Mute 5 Electric Focus Press the focus +/- keys to adjust the clarity of the picture. 6 Q&A * Check if the power cord is connected properly, and if the power light is on.Try to unplug and plug the power if the projector still can not boot up. * Do not cover lR receiver. * ln the infrared mode, make sure remote points at lR receiver directly. * There is an obstacle between the remote control and the projector. * The batteries are out of power or the battery is not installed correctly. Why is there no display when I connect HD port? * Check if the interface is securely connected. * The devices may be incompatible. * The lens is not clean. * The projection lens is not correctly focused. * The projector and the screen are not aligned properly. * The environment is too bright. * Please reboot the projector to test again. If the screen still freeze, please turn off for 10 minutes and turn on again. 7 Maintenance Suggestion Open filter from here To make this projector work longer, we recommend you to follow the suggestions. 1.Before cleaning the projector, turn off the projector, then turn off the main power and unplug it from the outlet. 2.Clean the filter regularly every month to prevent clogging. 3. Make sure to close the projector off once you finished using it. 4.Make sure not to use it continuously for more than 6 hours. 8 Using the device 1 Network & Internet This projector can connect to the Intemet through Wi-Fi. * On the home page, select " Setting " to go to the "Network & Internet", make sure that Wi-Fi is turned on. * Select your Wi-Fi network name when it appears in the list. * Complete the connection process by following on-screen prompts. 2 Bluetooth How do l connect a speaker to my projector? * Turn on the Bluetooth feature on your projector and the speaker. * On the home page, select ""Setting" to go to the "Bluetooth", make sure that Bluetooth is turned on. * Search for available devices on your projector's setting menu and select your audio system when it appears in the list. * Complete the pairing process by following on-screen prompts. 9 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. -This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.