Volta SE-03 MAX Electric Scooter User Manual

Introduction

This product is designed for environmentally friendly transportation. Throughout this manual, you will find information on the product's advantages and characteristic features. The general features are as follows:

• High efficiency brushless DC motor
• Electronic control unit (Driver) protecting against high and low voltage
• Safe braking with gas cut-off feature
• High capacity battery providing longer range and higher performance
• Front suspension providing a pleasant and comfortable ride
• Vehicle equipment in compliance with European standards

Important Notes

Rider and Passenger

• This vehicle is designed to carry a maximum of one rider.
• Please use the vehicle without exceeding the load limits specified in the vehicle's conformity certificate.

Road Conditions

• This vehicle is designed for use on flat and asphalt roads.
• Do not use the vehicle without reading the entire user manual.
• It is recommended to carefully read the "Warning, Caution, Note, and Safety Precautions" sections.
• You must take your vehicle to the nearest authorized service for maintenance after purchase.

CAUTION: You must adhere to the maintenance intervals specified in the user manual. Otherwise, your vehicle will be excluded from warranty conditions. The maintenance intervals and parts requiring replacement/checking for your vehicle are listed in this user manual.

WARNING: These headings are written to protect you from serious personal injury and mechanical damage.

Table of Contents

General View

The image displays an electric scooter with various parts labeled:

• 1. Front Suspension System
• 2. Headlight
• 3. Display
• 4. Handlebar
• 5. Battery
• 6. Seat
• 7. Rear Suspension
• 8. Stop Lamp
• 9. Rear Brake Disc
• 10. Disc Brake
• 11. Electric Motor
• 12. Side Stand
• 13. Front Brake Disc

WARNING: All parts listed in the user manual are for reference. The manufacturer may make changes without prior notice.

Operation and Usage

Starting Up

Insert the contact key into its slot and turn it to the 'on' position. The vehicle is in park mode after starting. To put it in riding mode, squeeze the brake lever. The vehicle will be ready for riding.

Acceleration

To accelerate, turn the throttle lever in the direction indicated by 'A' in the diagram. This will cause the vehicle to move. Turning the throttle lever in direction 'B' will decrease speed and acceleration.

Braking

The brake levers are equipped with brake sensors. This allows for both mechanical braking and cutting off the motor's energy. Squeeze the brake lever towards yourself with your fingers. To release the brake, slowly release the brake lever.

The vehicle is equipped with front and rear hydraulic disc brake systems. The brake lever on the right activates the front brake, and the brake lever on the left activates the rear brake. For both front and rear brakes, the free play of the brake lever should be between 5-10 mm. Braking should begin after this distance.

WARNING: Avoid sudden and hard braking, as this may cause the vehicle to skid and lead to accidents. Be careful when braking downhill. Do not accelerate while braking, as this may damage the electronic control unit and the motor. Brake pads, calipers, and brake discs can reach high temperatures during braking. Contact with these hot surfaces can cause serious injury. Ensure the parts have cooled down before performing maintenance or repair. The disc brake system offers high braking performance. Therefore, practice braking on flat surfaces. Braking can be adjusted for sensitivity. For safer deceleration, use both front and rear brakes together. Prolonged use of the brakes will heat the brake components and reduce their performance, increasing your braking distance and affecting safe stopping. Brake pads should always be replaced with original parts. Low-quality parts can damage other components of your vehicle and affect its performance. The braking system is vital for your safety. Ensure periodic checks and adjustments are performed by authorized service centers at the intervals specified in the periodic maintenance table.

Lighting Elements

The lighting system, located at the front and rear, should be used to increase visibility in dark and daytime riding conditions. Increasing visibility will enhance riding safety. According to regulations, the low beam headlight is automatically activated when the vehicle is started. To activate the lighting system, start the vehicle. Press the high beam headlight switch located on the left side of the panel for the high beam.

Electronic Control Unit

The electronic control unit (Driver) acts as the brain of your electric vehicle. Its software enables the motor to start. Due to the vehicle's equipment and software, the maximum speed is 45 km/h. This is controlled by the electronic control unit. It also ensures that commands sent from the panel are executed. The electronic control unit is protected against dust and splashes, but avoid excessive water accumulation.

Stands

A side stand is provided to keep the vehicle stable and upright. There is a side stand sensor. This sensor prevents the vehicle from receiving power when the side stand is deployed, ensuring your safety. Make sure the side stand is retracted for the vehicle to operate.

WARNING: The electronic control unit is protected against dust and splashes. However, avoid large water accumulations.

Charger

Charge your electric scooter for 4-5 hours with the charger provided with the vehicle before its first use. Follow the instructions below to charge the vehicle:

• Ensure your electric scooter is turned off.
• First, plug the part indicated by '2' of the charger into the socket.
• Then, insert the part indicated by '1' of the charger into the vehicle's charging port.
• When connecting the charger to the vehicle, sparks may occur.
• The charger has two indicator LEDs. The first LED, indicating operation, stays solid red. The second LED turns red during charging and green when the battery is full. If the charger has a red and green light, the battery is full. If your charger has only one LED, it turns red during charging and green when the charging is complete.
• Wait until the indicator light turns green.
• After charging is complete, remove the plug from the charging port and unplug the charger from the socket. Unplugging the charger from the socket extends the product's lifespan.

CAUTION: Damaged chargers due to voltage differences in your electrical system can damage your vehicle. Such damages are not covered by the warranty. Plugging the charger into the socket first will protect your vehicle from possible high/low voltage conditions. Charging at least once a month will extend your battery's lifespan. Disconnect the charger when the battery is fully charged.

WARNING: If the battery charging time exceeds the time specified in the manual, please report a fault. Battery performance may decrease in winter, reducing the vehicle's normal range.

• Use only the original charger specifically designed for your product.
• Your electric vehicle must be turned off while charging.
• Do not shake your vehicle while charging.
• Do not charge in rainy weather.
• The charger contains sensitive components. Therefore, do not expose the charger to any impact.

Battery

The vehicle is equipped with a rechargeable Lithium-ion battery providing 60V 12Ah of energy. The battery's usage affects the vehicle's lifespan and environmental conditions. Therefore, pay maximum attention to the following:

• Do not dispose of the battery with your household waste.
• Do not immerse the battery in any type of liquid.
• Do not connect the positive and negative terminals of the Lithium battery to each other.
• Do not expose the battery to direct sunlight or high temperatures.
• Do not disassemble the battery. Disassembling the battery will void the warranty.
• Do not charge the vehicle with any charger other than the charger provided with the vehicle.
• Do not store the battery in cold and humid environments. If storing for more than two months, charge it for two hours every two months.
• If the battery is to be disposed of or no longer used, deliver it to the manufacturer or an authorized waste collection facility.

CAUTION: Store your electric scooter in a place away from cold, preferably in a garage. This will extend your battery's lifespan. If you will not use your electric scooter for one month or more, charge the batteries at least once a month to maintain their performance.

Maintenance and Control

Brake Maintenance

Brake pads wear out due to their operating principle. They should be replaced when they reach a certain safety level. Safety level checks and replacements should be performed by authorized service centers. Unreplaced brake pads can lead to the brake system operating with reduced performance, making noise, and in some cases, breaking other parts. Brakes should be checked at every maintenance.

Tire Pressure Control

Check your tire pressure levels daily. Tire pressures above or below normal will affect the vehicle's road holding, acceleration, fuel consumption, and other performance aspects. Check your tires daily for any holes, cuts, or unusual conditions. Also, check the rims for dents, scratches, or bends that could cause air loss. Such damage can cause the vehicle's balance to be disturbed and lead to vibrations. If you notice such issues, visit your nearest authorized service center to have the damage repaired.

WARNING: Brake pads and discs must be kept free of oil/grease. If brake pads become contaminated, they must be replaced with new ones. Brake discs should be cleaned with detergent, rinsed, and dried. If the tire pressure is not correct, it will wear out faster and its lifespan will be shortened. Also, underinflated tires can reduce grip, leading to accidents. If the tire pressure is too low, the tire may detach from the rim. Your tires will wear out with use. You must replace the tires when the tread depth decreases. Tire life may vary depending on road, climate, and usage conditions. The user must regularly check tire pressure and tread depth. Tires with low tread depth will particularly reduce grip on wet surfaces. The minimum tread depth for front and rear tires is 0.5 mm. You must replace your tires when you see the tread wear indicator (TWI).

Fuse Replacement

The vehicle's charging circuit is protected by a 60A fuse against external interference and charger malfunctions. If the fuse blows or malfunctions, it needs to be replaced. To do this:

• Ensure the vehicle is turned off.
• Replace with a fuse of the same rating.

WARNING: Using a fuse with a lower capacity than specified may cause the system to continuously trip, while using a fuse with a higher capacity may damage electronic components due to high current and damage cables.

WARNING: Do not use high-pressure water when washing your vehicle. This will damage your electrical systems.

Throttle Adjustment

Check that the throttle lever moves freely up and down. The distance from the fully retracted position to the position where the first throttle response occurs should be between 2 and 6 mm. To adjust this, loosen the locking nut, turn the adjuster, and then tighten it again.

Cleaning

• It is recommended to clean your electric vehicle with a damp cloth.
• Never lubricate the brake assembly and tires.
• Use oil to clean the metal parts of your vehicle.
• Always use standard cleaning agents when cleaning painted plastic parts.
• Rinse with cloths after cleaning.

CAUTION: Never use high-pressure water when washing your electric scooter. High-pressure water can cause some parts to take in water. Parts that take in water may lose performance and become damaged.

Maintenance Schedule

Periodic maintenance should be performed at authorized technical service stations. Vehicles that are not regularly maintained (every 4 months) will be excluded from the warranty coverage.

Service/Motor Maintenance

• The electronic control unit (driver) of your vehicle is located under the seat. Therefore, be careful not to let water enter this area. Ensure that the cables entering this area are not strained and that the protective plastic is not damaged.
• To prevent damage to other parts, do not press the accelerator and brake simultaneously while operating.
• Slow down on rough road surfaces. Excessive vibration can cause cables to break within the motor and driver.
• Do not allow the water level to reach the motor height in rainy weather. Otherwise, your motor may be damaged.

WARNING: For the safety and longevity of your vehicle, please refrain from modifications. Modified vehicles will endanger your safety and the safety of traffic. Always use manufacturer-approved parts. Before performing any maintenance, turn off the motor for your personal safety and lift the vehicle onto its stand. Even for simple maintenance, do not perform it without the motor being off and the vehicle on its stand. If the vehicle has not been used for one month or longer, check parts such as tires and battery that are prone to wear or rust before the next use and start riding.

Motor and Chassis Number

Motor and chassis numbers are for your vehicle's registration and assist our authorized service centers in providing better service for maintenance/repair needs.

Motor No

Chassis Plate

CAUTION: Ensure that the motor and chassis numbers written on your electric vehicle are the same as those written on the Certificate of Conformity.

Storage and Commissioning

Vehicle Storage

• If you will not be using your electric vehicle for extended periods, such as during winter months, take precautions to protect your vehicle from damage and wear. It is advisable to perform some repairs before storage.
• Clean, rinse, and dry your electric vehicle. Coating painted surfaces with protective oil will extend the life of your paint and help maintain its original shine.
• Set your electric vehicle's tire pressure to the ideal level.
• Cover with a non-plastic or non-rubber cover. Store in storage conditions where the temperature does not change significantly. Significant temperature changes can cause many parts of your vehicle to fatigue, break, or crack.

Commissioning

• Remove the cover from your electric vehicle and clean it.
• After completing the pre-operation instructions, start your electric vehicle.
• Perform the first use in an area closed to traffic. Ensure all components of your electric motor scooter are functioning correctly and at full performance before entering traffic.

Transportation

Ensure the ignition is turned off when transporting your electric vehicle. Apply the front and rear brakes. To prevent any external damage to your vehicle, you can safely transport it by covering it with cardboard inside a metal cage.

Assembly

The electric vehicle is delivered assembled.

Technical Specifications

Manufacturer Information

The service life of your vehicle is 10 years, and the maximum repair time is 45 business days.

If you encounter any problems with your vehicle, you can access information about authorized service centers and spare parts by visiting our website at www.volta.com.tr. You can access all authorized service station information through the Ministry's Service Information System.

www.volta.com.tr

www.volta.com.tr/servis/

Warranty

Manufacturer Company

Address

• Volta Motor Gümüşova Factory, Selamlar Village, Selamlar Mevkii, Gümüşova OSB 1. Street No:10, Gümüşova / DÜZCE / TURKEY
• Tubitak MAM Technology Free Zone, Baris SB. Mh. 5001 Sk. No:3 A/B, Gebze / KOCAELI / TURKEY
• Volta Motor Cumayeri Factory, Yaka Mah. 401.Sk. No:19, 81700 Yukarıavlayan, Cumayeri / DÜZCE

Telephone

• +90 850 222 28 65
• +90 850 222 28 65
• +90 850 222 28 65

Fax

• +90 850 222 28 65
• +90 850 222 28 65
• +90 850 222 28 65

Product

• Type: ELECTRIC MOTORCYCLE
• Commercial Name: VOLTA
• Model: SE-03 MAX
• Chassis No:
• Delivery Date and Place:
• Maximum Repair Time: 45 Business Days
• Warranty Period: 2 Years

Seller

• Commercial Title:
• Address:
• Telephone:
• Fax:
• Invoice Date and Number:
• Sales Date:

This section must be filled out completely by the seller (stamp and signature).

Warranty Terms and Conditions

1. The warranty period is two years, and the presentation of the Warranty Certificate is required to benefit from the warranty. Therefore, this Warranty Certificate must be kept during the warranty period.
2. All parts of the product are covered by the warranty.
3. If the product is found to be defective, the consumer may exercise one of the following rights as per Article 11 of Law No. 6502 on Consumer Protection:
   • a) Declaring readiness to return the sold item and withdraw from the contract,
   • b) Keeping the sold item and demanding a reduction in the sale price proportional to the defect,
   • c) If excessive cost is not required, demanding the free repair of the sold item at the seller's expense,
   • ç) If possible, demanding the replacement of the sold item with an identical defect-free item.
4. In case of disputes arising from defects that occur within the provided warranty period, the invoice will be taken into account, and the presentation of the approved Warranty Certificate and invoice is required.
5. The warranty will be void if any tampering is detected on the invoice and warranty certificate, if the original serial number on the vehicle is removed or damaged.
6. The warranty will be void if the device's installation, maintenance, or repair is carried out by anyone other than our authorized service centers, or if the vehicle is repaired outside of authorized service.
7. Vehicle maintenance must be performed by authorized service centers at the intervals specified in the user manual provided with the vehicle. Vehicles that are not maintained on time will be excluded from the warranty coverage.
8. The warranty provided by our company does not cover defects arising from the use of the vehicle for purposes other than its intended use or under abnormal conditions, nor does it cover the following defects:
   • Defects arising from the addition of parts not manufactured or sold by Volta Motor to the vehicle,
   • Water ingress into parts due to washing with high-pressure water,
   • Wear, breakage, or malfunction of parts such as the motor and rims due to exceeding the maximum load capacities specified in the technical documents,
   • Defects arising from modifications made without the written approval of Volta Motor,
   • Normal wear and tear, aging, or performance loss of parts such as batteries, brake pads, tires, etc.
   • Liquid contact with electronic components,
   • Breakage or bending of shock absorbers and chassis mounting components due to exceeding the load capacities specified in the user manual or due to hard impacts,
   • Damage and malfunctions resulting from disasters such as fire, flood, water inundation, and lightning strikes,
   • Batteries are shelf-life products. Batteries that have been stored for more than 90 days without use (by the dealer or end-user),
   • Damage occurring during the transportation, loading, unloading, and carrying of the vehicle after delivery to the user.
9. No person other than the consumer identified on the invoice and warranty certificate can claim rights or compensation from the warranty.
10. The consumer may apply to the Consumer Arbitration Committee or the Consumer Court at their place of residence or where the consumer transaction took place in case of disputes arising from the exercise of warranty rights.