User Manual for DynaLabs models including: DYN-C-3000-DE Triaxial Capacitive Accelerometers, DYN-C-3000-DE, Triaxial Capacitive Accelerometers, Capacitive Accelerometers, Accelerometers
30 apr 2022 — Disclaimer. Dynalabs Ltd. provides this publication "as is" without warranty of any kind, express or implied, including but not limited to, ...
Manuals & Datasheets – Dynalabs
File Info : application/pdf, 8 Pages, 326.86KB
DocumentDocumentModel DYN-C-3000-DE 2g/4g/8g/10g/20g/40g/50g/100g/200g/500g Product Manual All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. Product Support If at any time you have questions or problems with the DYN-C-3000-DE sensors, please contact a Dynalabs engineer at: Phone: E-mail: +90 312 266 33 34 (9 a.m. to 5 p.m., UTC +3) info@dynalabs.com.tr Warranty Our products are warranted against defective materials and workmanship for one year. Defects arising from user errors are not covered by the warranty. Copyright All copyrights of this manual belonging to Dynalabs products are reserved. It cannot be reproduced without written consent. Disclaimer Dynalabs Ltd. provides this publication "as is" without warranty of any kind, express or implied, including but not limited to, the implied warranties of merchantability or fitness for a particular purpose. This document is subject to change without notice, and should not be construed as a commitment or representation by Dynalabs Ltd. This publication may contain inaccuracies or typographical errors. Dynalabs Ltd. will periodically update the material for inclusion in new editions. Changes and improvements to the product described in this manual may be made at any time. 2 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. Table of Contents 1) Introduction..........................................................................................................................................4 2) General Information.............................................................................................................................4 2.1) Unpacking and Inspection.............................................................................................................4 2.2) System Components......................................................................................................................4 2.3) Specifications ................................................................................................................................5 2.4) Outline Drawing............................................................................................................................6 3) Operation and Installation ....................................................................................................................7 3.1) General ..........................................................................................................................................7 4) Sensor Static Calibration Verification .................................................................................................7 5) Declaration of Conformity ...................................................................................................................8 3 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 1) Introduction Capacitive accelerometers are based on proven micro-electro-mechanical systems (MEMS) technology. These capacitive accelerometers are reliable and long-term stable. These sensors are Differential Ended type DC response sensors. The advantage of these sensors is their outstanding temperature stability, their lightweight and they are low cost sensors. These sensors have reliable aluminum housing with IP68 protection class. These sensors feature standard reliable aluminum housing with protection class IP68. Steel housing is also possible. Dynalabs 3000DE series accelerometers provide an outstanding noise performance from 20 to 260 g/Hz. These accelerometers provide a wide frequency range (±3dB) from 1,500 Hz to 3,000 Hz. DYN-C-3000-DE sensors offer the following options; · Custom Cable Length (5m standard cable) · Custom Housing Material · Custom Connector · Base plate 2) General Information 2.1) Unpacking and Inspection Dynalabs products provide adequate protection for undamaged products to be transported. Document the damages that occur indirectly during the transport and contact the customer representative. 2.2) System Components The DYN-C-3000-DE has the following components: - MEMS Sensor - Calibration Certificate - Product Manual 4 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 2.3) Specifications Table 1: Specifications datasheet Full scale acceceleration Frequency range (±3dB) Non-linearity (full scale) Noise (in band) (g) (Hz) (%) (g/ Hz) 3002DE 3004DE 3008DE 3010DE 3020DE 3040DE 3050DE 3100DE 3200DE 3500DE ±2 ±4 ±8 ±10 ±20 ±40 ±50 ±100 ±200 ±500 1,500 1,500 1,500 1,500 1,500 1,500 3,000 3,000 3,000 3,000 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 25 25 25 80 75 110 35 50 80 170 Scale factor (nominal) Shock survivability (mV/g) (g) 400 5,000 200 5,000 100 5,000 80 5,000 40 5,000 20 5,000 40 5,000 20 6,000 10 6,000 4 6,000 Environmental Table 2 Environmental specifications datasheet Protection Level Operating Voltage Operating Temperature Operating Current Consumption mA Isolation IP 68 6 V 20 V -40 °C to +100 °C 21 mA Case isolated 5 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. Physical Table 3 Physical specifications datasheet Sensing Element Housing Material Connector (Optional) Mounting Base plate (Optional) Weight (without cable) MEMS Capacitive Aluminum or Steel D-Sub 9 or 15 pin, Lemo, Binder Adhesive or screw mount Aluminum or Steel 19g (aluminum) 44 g (steel) 2.4) Outline Drawing The dimensional properties of DYN-C-3000-DE sensors are given below. 6 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 3) Operation and Installation 3.1) General The general sensor connector configuration is given below; Cable Code/Pin Configuration: · Red : V + Power supply voltage +6 to +20 VDC · Black : Ground Power GND · X-Axis : Yellow : Signal(+) Positive, analog output voltage signal for differential mode. Purple : Signal(-) Negative, analog output voltage signal for differential mode. · Y-Axis: Blue : Signal(+) Positive, analog output voltage signal for differential mode. Green : Signal(-) Negative, analog output voltage signal for differential mode. · Z- Axis: White : Signal(+) Positive, analog output voltage signal for differential mode. Orange : Signal(-) Negative, analog output voltage signal for differential mode. WARNING Never connect the power supply and/or the power ground to yellow, purple, blue, green, white and/or orange cables. Never connect the power supply to the power ground. Always use a clean power source and check the voltage range. 4) Sensor Static Calibration Verification Using gravity, voltage values are measured in the + and - directions, providing a value of 1 g. The measurement should be made as follows; When the acceleration value of 3000DE series sensors is entered into the data acquisition system, the sensor shows +1 g with the effect of gravity, which is in the direction of the axis to be calibrated. When the sensor is positioned in the opposite direction to the axis to be calibrated, the arrow shows -1g as shown below under the effect of gravity. Using gravity, the voltage values that provide 1 g in the + and - directions are measured and compared with the catalog value. The calibration value should be close to the catalog value with a 10% tolerance. Sensor catalog sensitivity values are given in Table 1. 7 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 5) Declaration of Conformity This declaration of conformity is issued under the sole responsibility of the manufacturer. The product(s) are developed, produced and tested according to following EC- directives: · 2014/35/EU Low Voltage Directive (LVD) · 2006/42/EU Machinery Safety Directive · 2015/863/EU RoHS Directive Applied standards: · EN 61010-1:2010 · EN ISO 12100:2010 · MIL-STD-810-H-2019 (Test Methods: 501.7 - High Temperature, 502.7 - Low Temperature, 514.8 - Vibration, 516.8 Shock) DYNALABS MÜHENDSLK SANAY TCARET LMTED RKET declares that above mentioned products meet all the requirements of the above mentioned standards and regulations. Murat Aykan, Technical Manager Ankara, 15.07.2021 8