Quick Install Guide

Introduction

The EL-SC-100 Controller can be used as a standalone system controller or as an Extender to any gSC OR SC controller running g!6.6 or greater. Consult the ELAN Training Guide for detailed EL-SC-100 control capabilities. The ELAN Training Guide provides valuable hardware and software reference documentation and is an important supplement to this document. Ensure you have the latest version by visiting the ELAN Dealer website at www.elancontrolsystems.com and following the Dealer Resources link.

Included in the box:

• EL-SC-100 Controller
• 12vDC Power Supply

Important Safety Instructions

1. Read, understand, and follow ALL safety and installation instructions included in this manual. Failure to follow the included documentation may damage the product and void the manufacturer's warranty.
2. Follow ALL installation guidelines included with the product. Installation in high humidity environments, near heat sources, or in non-recommended locations may impede, interfere with, or damage the intended operation of the product.
3. Only use attachments and accessories specified by the manufacturer.
4. The use of abrasive, liquid, or solvent-based cleaning fluids will damage the product. Refer to and follow all Product Care instructions.
5. Product servicing may only be completed by authorized or certified service centers and personnel. For a complete list of servicing options, follow instructions in the product documentation and/or contact the original manufacturer.

FCC and IC Information

This Class B digital apparatus complies with Part 15 of the FCC rules and with Canadian ICES-003 and RSS-247. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.

(Note: The original document contained French text regarding FCC/IC compliance, which has been translated to English for this primary language version.)

Warning:

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC and IC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine evaluation limits in section 2.5 of RSS 102. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters from user and bystanders.

Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC and IC Registrations

FCC ID: EF400186

IC: 1078A-00186

Z-Wave Operating Frequency

• Australia/New Zealand: 921.42/921.40/919.80MHz
• US/Canada: 908.42/908.40/916MHz
• European: 868.42/868.40/869.85MHz

Z-Wave Developer's Kit:

7.13.1

Z-Wave Network Operation

This product can be operated in any Z-Wave™ network with other Z-Wave certified devices from other manufacturers. All mains-operated nodes within the network will act as repeaters regardless of vendor to increase network reliability. In an ELAN SC Series System Controller, the host application controls the device reset feature. If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned, and it will be necessary after the reset to exclude and re-include all nodes in the network. If this controller is being used as a secondary controller, use this procedure to reset it only if the network primary controller is missing or otherwise inoperable.

EL-SC-100 Overview

Dimensions: 6.95 in. x 4.94 in. x 1.30 in.

Front Panel Features:

• Power Button: Used to turn the unit on/off.
• Status Indicator: An LED that communicates the controller's status.
• Reset: A recessed pinhole button for resetting the device.

Rear Panel Ports:

• RS-232: For serial communication.
• IR OUTPUTS: Three discrete outputs for controlling IR devices, compatible with Xantech single and dual emitters.
• AUDIO SENSE: Input for ELAN audio sensors.
• OSD: On-Screen Display output for connecting to a display or AVR.
• USB: For connecting accessories like the optional USB Z-Wave antenna.
• LAN / PoE: Gigabit Ethernet port for network connectivity and Power over Ethernet.
• DC Power: 12V DC power input.

Mounting

The EL-SC-100 is designed for flexible mounting: on a shelf, in a cabinet or rack, or in a structured wiring enclosure using an optional mounting bracket.

Wall Mounting:

The chassis is designed for convenient wall mounting in any orientation. Use the arrows on the rear panel to mark screw locations. Mount screws leaving approximately 3/16" (5mm) of the screw exposed. Slide the chassis over the screws. Ensure a 3/16" gap is left between screw heads and the wall.

Diagram Description: An illustration shows how to mark screw holes on a wall using arrows found on the rear panel. Another diagram presents a mounting bracket template with overall dimensions of 7 inches by 5 inches, indicating internal mounting points spaced 3 inches apart.

Structured Wiring Cabinet Mounting:

Using the optional Structured Wiring Cabinet Mount:

1. Attach the mounting bracket to the wiring cabinet using snap rivets and washers.
2. Snap the controller onto the two hooks on the mounting bracket.

Diagram Description: Two diagrams illustrate the process of attaching a mounting bracket to a wiring cabinet and then securing the controller to the bracket.

Shelf Mounting:

The EL-SC-100 features rubber feet to protect finished surfaces. Place the controller on a stable surface, ensuring connected wiring is managed to avoid tension on the connections.

Connections

Serial Connection:

Connect an RS-232 serial controlled device using an RJ45 connector (not included) to the RS232 port on the rear of the controller. The EL-SC-100 is not compatible with RS-485 serial devices; use a gSC10 controller for RS-485 connections.

RJ45 Connector Pin-Out:

• 1: (Unspecified)
• 2: CD (Carrier Detect)
• 3: DTR (Data Terminal Ready)
• 4: SG (Signal Ground)
• 5: RD (Receive Data)
• 6: TD (Transmit Data)
• 7: CTS (Clear To Send)
• 8: RTS (Request To Send)

Diagram Description: An illustration shows an RJ45 connector and its pin configuration, numbered 1 through 8, with corresponding signal names.

Sense Input Connection:

ELAN sensors can trigger events from third-party devices. The status is binary (ON or OFF). This can be used to trigger or condition an event map. Connect only ELAN sensors to this port.

Available ELAN Sensors:

• Audio Sensor (P/N: AUDSENSOR)
• Video Sensor (P/N: VIDSENSOR)
• Contact Closure Sensor (P/N: CTSENSOR)
• Current / Magnetic Field Sensor (P/N: CRSENSOR)
• Light / LED Sensor (P/N: LTSENSOR)
• Voltage Sensor (P/N: VTSENSOR)

IR Output Connection:

Three discrete IR outputs are provided to control third-party devices, compatible with Xantech single and dual emitters.

Diagram Description: A diagram shows the IR OUTPUTS ports connected via cables to external devices labeled DVD, Media Player, and TV.

HDMI Connection:

The EL-SC-100 includes an HDMI connector for an On-Screen Display (OSD) interface. Connect the OSD output to an available HDMI input on a display or AVR.

USB Connection:

The USB connection is primarily for the optional USB Z-Wave antenna. Refer to integration notes for configuring Z-Wave devices through the EL-SC-100.

LAN / PoE Connection:

The EL-SC-100 features a Gigabit PoE compatible Ethernet port. Connect an Ethernet cable to an available network port. A wired connection is preferred over Wi-Fi. The unit can be powered over Ethernet (PoE) with a minimum requirement of IEEE 802.3at (42.5 - 57 VDC, 600 mA maximum).

Reset Button Procedures

The recessed pinhole reset button on the right side of the controller can be used in three ways:

1. 2-second press and release: Resets the controller to DHCP.
2. 20-second press and release: Removes all configuration information, while maintaining the software version.
3. 10-second press and release (during power-on): Performs a full factory reset, reverting to the factory default software version. ⚠️ WARNING: DO NOT remove power during a factory reset, as it will permanently damage the unit. Allow approximately 4 minutes for the unit to reboot and become discoverable. The LED will remain red during the reset process. These actions cannot be undone.

Powering On and Status Indicators

Power:

Once all other connections are complete, connect an Ethernet cable to a PoE switch or the 12 VDC, 1A power supply to the DC input.

Power Button:

• When the controller is off, a short press powers the unit on.
• When the controller is on, a short press (less than three seconds) restarts the controller.
• When the controller is on, a long press (3 seconds or longer) powers down the controller.

LED Status Indicator:

The LED communicates the status of the controller:

• Blue: Connected OK / Power
• Blue flashing: Boot up
• Amber: No network found
• Red: Boot failure
• Red flashing: Self-check failure

Network and Software

Network Connection:

The EL-SC-100 is factory set to use DHCP. Connect to a wired network and use the ELAN Configurator to connect to the controller. Once connected, use the configurator to set a static IP address or connect via Wi-Fi.

Software Update:

Before configuring the controller, upgrade the software to the latest available version from the ELAN Dealer Resources portal. Download and open the executable file, then follow the on-screen instructions.

Limited Warranty

Nortek Security & Control (NSC) warrants the EL-SC-100 to be free from defects in materials and workmanship for a period of two (2) years from the date of purchase. If a defect is found within the warranty period, NSC will repair or replace the item at its option.

This warranty does not apply to:

• Equipment not manufactured by NSC.
• Equipment installed by non-authorized installers.
• Equipment not installed to NSC's specifications.
• Equipment repaired or altered by others than NSC.
• Equipment subjected to negligence, accident, or damage beyond NSC's control (including lightning, flood, electrical surge, tornado, earthquake, or other catastrophic events), or to improper operation, maintenance, or storage.

For equipment sold but not manufactured by NSC, NSC's warranty obligations conform to the warranty extended by its supplier. This warranty excludes reimbursement for labor, transportation, removal, installation, or other expenses incurred in connection with repair or replacement.

NSC shall not be subject to any other obligations or liabilities whatsoever with respect to equipment manufactured by NSC or services rendered by NSC, except as expressly provided and authorized in writing.

The foregoing warranties are exclusive and in lieu of all other expressed and implied warranties, including implied warranties of merchantability and fitness for a particular purpose.

Customer Support and Authorized Resellers:

To ensure quality support, Nortek Security & Control products are sold exclusively through authorized dealers and are not sold online. Warranties are NOT VALID if products are purchased from an unauthorized dealer or online E-tailer. To verify if a reseller is authorized, please call Nortek Security & Control at (707) 283-5900.

Website: www.nortekcontrol.com

©2020 Nortek Security & Control LLC. All Rights Reserved. ELAN is a registered trademark of Nortek Security & Control LLC.

Part Number: 10024269 Rev-C