RF Exposure Statement

This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Split-type Smart Toilet Lid Instructions

The product is a split-type smart toilet lid, model RF001, manufactured by Foshan Gaojie Technology Co., Ltd. The brand visible on the product is Lxlu.

Safety Instructions

Before use, please read through the safety instructions carefully so that you can use the product correctly. Pay attention to the following warnings, which are related to safety:

• ⚠️ Warning
• ? Strictly prohibited
• ✅ Enforce compliance
• ℹ️ Notice

If the above warning signs are disregarded, injuries or life-threatening injuries may occur.

Unsupervised use of this equipment is prohibited for persons (including children) with physical, sensory, or mental impairments or lack of experience and common sense due to limited cognitive abilities and/or lack of necessary knowledge. Unless they are supervised or instructed in using the product by a person responsible for their safety. Unsupervised children should not use the appliance alone and ensure that children do not play with it.

General Safety Precautions

• Do not splash the product with water. May cause fire or electric shock.
• ? Grounding: Class I appliances must be connected to a ground wire. Failure to do so may result in product malfunction or electrical leakage.
• Guidelines to be followed compulsorily: If the power cord is damaged, it must be replaced by the manufacturer or its service department or similarly specialized personnel in order to avoid danger.

Electrical Safety

• Only suitable for the power supply required in the technical specifications; it is strictly prohibited to use too many loads on the same socket. May overheat or cause fire.
• Ensure that the power plug is not wet with water, detergent or urine. May cause fire or electric shock.
• Do not pull/tug on the power plug/cord. May cause fire or electric shock.
• Do not use loose sockets. May cause fire or electric shock.
• Do not plug/unplug the power cord with wet hands. May cause electric shock.

Installation and Usage Safety

• Do not disassemble, repair or modify the product by yourself. May cause fire or electric shock.
• Unplug the product when cleaning. May cause electric shock.
• Do not connect to water pipes other than the mains. May cause skin infection or product failure.
• Do not place lighted cigarettes or other combustibles near the product. May cause fire.
• Do not bend or twist the water supply hose. May cause water leakage.
• Do not place heavy objects on the toilet seat or lid. May damage product.
• Do not turn the product upside down. May damage product.

Cleaning Precautions

• Please use diluted kitchen cleaner for cleaning. Do not use the following items: Benzene, paint thinner, stain remover, nylon brushes, etc.

Environmental and Usage Conditions

• Do not place this product in direct sunlight. It may cause discoloration of the product and failure of the seat heating function.
• The room temperature in the bathroom should be above 0°C. Otherwise, the product may freeze. Use a heater or other means to raise the bathroom temperature.
• Do not pour urine on the body and nozzle. May cause clogging.
• Do not use a non-compliant power supply. May cause product malfunction.
• Do not lean on the lid when in use. May damage the product.
• Unplug the product from the mains when there is thunder or lightning. Otherwise, it may cause product malfunction or product damage.
• When not in use for a long period of time, empty the stored water and unplug the product. Otherwise, it may cause water contamination and skin infection.

Product Description

The product is a split-type smart toilet lid. Key components include:

• Toilet Lid
• Digital Screen
• Toilet Seat
• Night lamp 2
• Nozzle
• Night lamp
• Water/Seat Temperature Adjustment Buttons
• Buttons
• Water inlet hose connection

Component Description

1. Toilet lid (Brand: Lxlu)
2. Fixed part: Includes Connecting bolt, Adjustment plastic seat, Fixed plate, Expansion nut.
3. Tee connector
4. Water inlet hose (includes Filter screen)
5. Remote control: Includes Remote control bracket.
6. Instruction (Manual for Split-type smart toilet lid)
7. Certificate of Conformity

Installation Steps

Installation tools (bring your own)

• Phillips screwdriver
• Movable wrench
• Bucket and rag
• Power pliers

Precautions before installation

• ⚠️ Attention
• Water pressure range: 0.1-0.75MPa, please follow the instructions.
• The angle valve should be close to the position where this product is installed and removed.
• Please use the new braided hose that comes with the product; the old braided hose cannot be used to prevent water leakage.
• When installing the braided hose, be careful to prevent the black gasket inside from falling out.

Installation Steps

1. Remove the old cover plate.
2. Place the installation template on the ceramic, taking care to align it with the front edge of the toilet.
3. Detailed steps for mounting the base plate:
   1. Plug the expansion nut into the ceramic hole.
   2. Place the fixing plate in the notched part of the mounting template.
   3. Place the adjustable plastic seat in the mounting groove.
   4. Place the adjustable plastic seat in the mounting slot.
   5. Place the screws in the expansion nut holes and tighten them.
4. Disassemble the keypad.
5. Push the cover plate in the direction shown in the figure until you hear a "click" sound, indicating that it is installed in place.

Installation Procedure

6. Close the Triangle valve.
7. Braided hose installation: For straight-sided toilets or straight end connections, ensure proper hose connection. If the ceramic shape is similar to Figure 3 (hemmed toilet), it is recommended that the elbow end of the braided hose be connected to the electronic cover plate.
8. Installation procedure T - shaped: If the angle valve is too close to the wall to be mounted, the tee connector can be mounted below the toilet tank inlet.
9. Open the angle valve and check whether there is water leakage.
10. Hold the sensing area of the seat ring with your right hand, and turn on the knob with your left hand to check whether the spray pipe extends. Pay attention to blocking the sprayed water with your hand to prevent it from splashing.
11. Connect to the power supply.

Notice

• It is strictly prohibited! Make sure to turn on the angle valve first and then connect to the power supply so as to protect the heating device.
• It is strictly prohibited to move the product from the toilet lid part, as it may easily cause mechanical failures.
• It is strictly prohibited to connect hot water higher than 40°C and cold water that may freeze.

Remote Control Instruction

The remote control allows operation of various functions. Key buttons include:

• CLEAN ECO LIGHT
• WATER TEMP. SEAT TEMP. AIR TEMP.
• AUTO
• REAR/MOVE
• FEMININE/MOVE
• DRYER
• STOP
• + / -
• < / >

Function Descriptions

• Auto Button: Press the "Auto" button to activate the one-touch automatic function, which performs hip wash, mobile wash, and drying.
• Rear/Female/Move:
• REAR/MOVE: Washes the hip area or performs mobile cleaning.
• Female Wash / Move Wash: Specifically for women, cleans the lower body or performs mobile washing.
• Function Duration: These functions can be used for up to 2 minutes. Hip wash and female wash can be switched.
• Additional Functionality: Other function buttons can be used in conjunction.
• Automatic Stop: The rear wash / female wash function stops automatically when the user leaves the seat.
• Drying function: Press the "Dry" button to blow warm air. The "Wind Temperature" button adjusts drying temperature through four settings. The function can be used for up to 3 minutes.
• Water pressure adjustment - sprinkler position: Press "REAR/MOVE" then "Water Temperature" to adjust water pressure (+/- buttons, four levels). The product's water inlet has a filter that may require cleaning if water pressure is low. Use "<" or ">" buttons to adjust nozzle position (four levels). Press "Move" for automatic back-and-forth cleaning. Water pressure and nozzle position default to last use. Press "Stop" to end functions.

Manual Cleaning Button

Turn on or off the manual wash functions.

Night Light Button

Turn on or off the night light functions. The night light is enabled by default.

Buttocks Washing/Moving Button

Used for buttocks washing and moving the buttocks washing function.

Warm Air Drying Button

Dries the washed area with warm air.

Stop Button

Stops buttocks washing, female washing, and warm air drying.

Water Temperature/Seat Temperature/Air Temperature Button

Adjusts water temperature during cleaning. The seat temperature button adjusts the seat ring temperature. The air temperature button adjusts the warm air temperature.

Smart Toilet Body Knob/Water Temperature/Seat Temperature

1. Rotate the knob forward to activate female cleaning (lower body wash).
2. Rotate the knob backward.
3. Press the knob once to stop rear wash, female wash, or drying. Press again to activate drying.

Temperature Levels:

• Water Temperature: Room Temperature, Low (36°C), Medium (38°C), High (40°C)
• Seat Temperature: Room Temperature, Low (32°C), Medium (35°C), High (38°C)

Cleaning and Maintenance

Manual cleaning of the spray nozzle

When there is no one seated, press the "Clean" button on the remote control for 3 seconds. The spray bar will extend for manual cleaning. Pressing stop retracts the spray bar.

Cleaning the filter screen

Warm Tips:

• If water flow is smaller than usual, clean the filter screen.
• Disconnect power and turn off the angle valve before cleaning.
• The filter screen is at one end of the braided hose. Clean with a small brush and reinstall.

Cleaning the product surface

Note: Please disconnect the power supply before cleaning!

• Use a sponge or soft cloth with normal temperature water or neutral detergent to wipe the surface.
• Lift the upper cover and seat ring to clean other parts.
• Do not put the cover back on until the ceramic toilet is completely rinsed to prevent detergent evaporation from corroding the surface.

Earth leakage protector

Please check the earth leakage protector regularly (at least monthly).

• Inspection methods:
• Press RESET: Indicator light turns on, power connected.
• Press TEST: Indicator light goes out, power disconnected.

If problems occur, stop use immediately and contact the supplier or service hotline. Ensure the indicator light is always on during operation. If an earth leakage protector is already installed, check it using these methods.

Schematic diagram of the earth leakage protector: [earth leakage protector diagram with RESET and TEST buttons]

Note: When the bathroom temperature is lower than 0°C or the product is not used for a long time:

• Please unplug the power plug and turn off the angle valve to stop water inlet.
• Remove the water inlet hose and drain the water from it.

Troubleshooting and Solutions

Troubleshooting for Fault Causes

Before checking for malfunctions, confirm:

• Power Supply: Is it working properly?
• Water Supply: Is it normal? Is the angle valve closed?

If the following phenomena occur, immediately cut off power and contact after-sales service:

• The earth leakage protector trips frequently.

Note: For large water leakage not from the water outlet, close the angle valve and cut off power simultaneously.

Analysis of Cleaning Faults

Troubleshooting for Seat Ring Heating Faults

Analysis of Lighting Malfunctions Phenomena

Product Dimension Diagrams

The diagram shows the dimensions of the smart toilet lid in millimeters (mm). Key dimensions include length ranges from 115-178mm and 446-491mm, width around 380mm, and height around 196mm and 105mm.

Technical Specifications

Rated Power: The product's rated power is determined under the following conditions: ambient temperature of 20±5°C, inlet water temperature of 15±1°C. The product is powered on and activated, with water and seat temperatures set to the highest level. The feminine wash function is tested (with an approximate flow rate of 660ml/min). The average power is measured during one continuous and stable cleaning cycle (lasting 2 minutes).

Warranty Card

Dear Customers:

Thank you for choosing our electronic toilet seats! When problems arise during use, please follow the user manual to simply troubleshoot and check. If you are unable to resolve the issues, please contact us at: Bidet-Toilet-Seat-Service-US@outlook.com.

1. Information

2. Precautions for the Warranty Card

1. Please fill in all the contents of the warranty card completely.
2. The warranty card and the invoice are important vouchers for enjoying the warranty service. When the product breaks down within the warranty period and the dealer or the company's after-sales service staff comes to repair it, please present the warranty card and the invoice.
3. The warranty card cannot be reissued, so please keep it properly.

3. Regulations on Free Maintenance

During the warranty period, if the product breaks down within the normal usage range in accordance with the operation instructions, precautions and other contents, the company will provide free maintenance.

4. The following situations do not fall within the scope of free maintenance

1. Those beyond the warranty period.
2. Those unable to present valid invoices and warranty cards within the warranty period.
3. Failures or damages caused by transportation, collision, etc. after purchase.
4. During the warranty period, failures and damages caused by abnormal use, human factors or natural disasters, such as fire, earthquake, flood, lightning or environmental pollution that result in product failures or damages.
5. Product failures or damages caused by users' self-disassembly, modification or repair on their own for reasons or responsibilities of their own.
6. Failures or damages caused by violation of maintenance regulations during use, such as using cleaning agents not in line with maintenance requirements or improper wiping and maintenance methods.
7. Failures or damages to consumables (such as sealing rings, etc.) or products caused by sand, impurities and other reasons.
8. Secondary relocation requested by customers.