Elimko - Otomatik Kontrol'da Güvenilir İsim
User Manual for Elimko models including: E-KC-102 Series Head Mounted Type Temperature Converter, E-KC-102 Series, Head Mounted Type Temperature Converter, Mounted Type Temperature Converter, Type Temperature Converter, Temperature Converter, Converter
23 ago 2024 — It s not used n med cal appl cat ons. KY-KC102-0524-1. E-KC-102 SERIES HEAD MOUNTED TYPE. TEMPERATURE CONVERTER USER MANUAL ...
File Info : application/pdf, 2 Pages, 240.37KB
DocumentDocumentE-KC-102 SERIES HEAD MOUNTED TYPE TEMPERATURE CONVERTER USER MANUAL Elimko KY-KC102-0524-1 The E-KC-102 converter is designed for use in an industrial environment. m The package of the E-KC-102 converter contans; the Converter, user manual and guarantee certfcate. m After openng the package, please vsually check whether the type of the transmtter s sutable for the order, whether the above-mentoned parts are mssng and whether the transmtter has been damaged durng shpment. m Before nstallng and operatng the controller, please read the user manual thoroughly. m The nstallaton and confguraton of the controller must only be performed by a person qualfed n nstrumentaton. m Keep the unt away from flamable gases, that could cause explotons. m Do not use alcohol or other solvents to clean the transmtter. Use a clean cloth soaked n water tghtly squeezed to gently wpe the outer surface of the transmtter. m It s not used n medcal applcatons. 1. DESCRIPTION E-KC-102 series two wire transmitters are microprocessor based industrial instruments in plastic case. E-KC-102 transmitters are used to convert the thermocouple and resistance thermometer signals into standard 4-20 mA The configuration of the transmitter is done by PC, using a software programme supplied by Elimko. The RS 232 connection hardware is also available from Elimko. 2. TECHNICAL SPECIFICATIONS 2.1. OPERATING RANGE and MEASURING ACCURACY (at 24 V supply voltage and 25°C ± 3°C ambient temperature) SENSOR RTD Pt-100 B E J K T/C N R S T L U mV STANDARD LOWER LIMIT UPPER MINIMUM LIMIT SPAN ACCURACY A/D D/A IEC 60751 -200°C 850°C 50°C ±0.25°C 100°C 1800°C 100°C ±2.00°C -200°C 840°C 50°C ±0.50°C -200°C 1120°C 50°C ±0.50°C IEC 60584 -200°C 1360°C -200°C 1300°C -40°C 1760°C 50°C 50°C 100°C ±0.50°C ±0.50°C ±1.00°C ±0.1% Span -40°C 1760°C 100°C ±1.00°C -200°C 400°C 50°C ±0.50°C DIN 43710 -200°C 900°C 50°C ±0.50°C -200°C 600°C 50°C ±0.50°C -2000mV 500mV 25mV ±0.075mV If the input type and scale is not specified while ordering, factory settings are; For KC-102-RT Input Type : Pt-100, and Scale : 0-200°C, For KC-102-TC Input Type : Type K, and Scale : 0-400°C. KY-KC100-0224-1 2.2. General Specifications Electrical: Supply Voltage Voltage Drop 10.0 - 30 V DC 10.0 V Environmental Conditions: Operating Temperature Protection Class -10°C to +55°C IP 00, IP 66 (DIN 43729 mounted on type B head) Calbraton Temp. Mechancal: Dmensons Weght (approx.) Connecton Cables 25°C ±3°C Ø 44.0 mm x 21.5 mm 40 g Max. 1.5 mm² (AWG 16) Resstance Thermometer (RTD) / Resstance Input: Sensor Connecton 3-wire or 4-wire (Configurable) Maximum Wire Resistance 100 W Error Signaling Wire Break (Output current can be configured Up / Down.) Thermocouple (TC) / mV Input: Input Impedance > 10 MW Maximum Wire Resistance 100 W Cold Junction Compensation (CJC) Constant, Internal NTC, External Pt-100 (Configurable) Error Sgnalng Wre Break (Output current can be confgured Up / Down.) Output: Output Signal Load Resistance Operating Influences: Ambient Temperature CJC Error (For TC Inputs) EMC Immunity 4 - 20 mA or 20 - 4 mA [Vsupply-10]× 50 W (600 W at 22 V DC) < ± 0.01% / °C < ± 1.0 °C < ± 0.5% Span Electromagnetic Compatibility: The E-KC-102 meets the requirements of TS EN 61326-1. E-KC-102 SERIES HEAD MOUNTED TYPE TEMPERATURE CONVERTER USER MANUAL 3. CONNECTION DIAGRAM Measurement Unit DC Power Supply Measurement Unt RL RL Elimko KY-KC102-0524-1 DC Power Supply Elimko Elimko PC Connection Connector 102-RT 4W PC Connecton Connector 102-TC 4 Wre RT E-KC-102-RT Connecton Dagram TC E-KC-102-TC Connecton Dagram m Before operating the converter, ensure that the converter is correctly configured. Incorrect configuration could result in damage to the process being controlled. m To minimize the pick-up of electrical noise, the wiring of low voltage lines, particularly the sensor input should be routed away from the high-current power cables. Where it is not possible, use shielded cable and ground the shielded cable. m The cables used for powering the transmitter and the power outputs must conform to the standarts IEC 60245 and IEC 60227. 4. DIMENSIONS Ld Ld 1 2 ø = 7.2 mm 3 6 4 5 ø = 6.0 mm 33.0 mm ø = 44.0 mm KY-KC102-0524-1 21.5 mm For thermocouple inputs, be sure to use the proper compensation cables and pay attention to the polarity of the connection. Manufacturer / Technical Support : Elimko Elektronik malat ve Kontrol Ltd. ti. ASO 2. Organize Sanayi Bölgesi Alci OSB Mahallesi 2001. Cad. No:14 Temelli 06909 Ankara / TURKYE Tel: +90 312 212 64 50 (Pbx) · Fax: +90 312 212 41 43 E-mail: elimko@elimko.com.tr · www.elimko.com.tr