Owner's Manual for SEKO models including: PSS8, PI PVC 400, PIR PVC 200, PSS8 Triple Probe Holder Vessel, PSS8, Triple Probe Holder Vessel, Probe Holder Vessel, Holder Vessel
PSS8 - Vaso Portasondas Triple Con Sensor De Caudal SEKO | PoolComet
Cables, buffer solutions and probe accessories Immersion probe holders Probe Accessories Sensors for measuring pH, Redox and Conductivity must be installed in the system using special probe holders that ensure the correct mechanical protection and degree of impermeability. The pH and Redox measurement probes can be submerged in tanks, inserted in pipes or placed in sample draw down containers (Catch Pots). The immersion models with adjustable flange can be used in conjunction with a counter-flange which allows quick and easy installation and removal. The P-IG range with a floating platform adapts to the varying liquid level of deep water tanks. The polypropylene versions PIR-2-PPxxx can house two sensors, e.g. pH and Redox. It is not recommended to use PH and/or Redox sensor in the same probe holder as a conductivity cell. Immersion probe holder Immersion probe holder PI Immersion No. of probes Max Temperature Material PI PVC 400 400 mm PI PVC 800 800 mm PI PVC 1000 1000 mm PI PVC 1500 1500 mm PI PVC 2000 2000 mm Code 9900100111 1 40°C PVC Code 9900100112 1 40°C PVC Code 9900100115 1 40°C PVC Code 9900100113 1 40°C PVC Code 9900100116 1 40°C PVC PIR PVC Immersion No. of probes Max Temperature Material PIR PVC 200 Code 9900100101 100÷250 mm 1 40°C PVC PIR PVC 400 Code 9900100102 100÷450 mm 1 40°C PVC PIR PVC 800 Code 9900100103 100÷850 mm 1 40°C PVC PIR PVC 1000 Code 9900100105 100÷1050 mm 1 40°C PVC PIR PVC 1500 Code 9900100106 100÷1550 mm 1 40°C PVC > > > 28 seko water & industry control and measuring instuments Immersion probe holder Immersion probe holder PIR 2 PP Immersion No. of probes Max Temperature Material PIR 2 PP 400 Code 9900100121 100÷450 mm 2 80°C PP PIR 2 PP 800 Code 9900100122 100÷850 mm 2 80°C PP PIR 2 PP 1000 Code 9900100124 100÷1050 mm 2 80°C PP PCIR PP Immersion PICIR PP 400 Code 9900100141 100÷450 mm 1 80°C PP PICIR PP 800 Code 9900100142 100÷850 mm 1 80°C PP PICIR PP 1000 Code 9900100144 100÷1050 mm 1 80°C PP PICIR PP 1500 Code 9900100145 100÷1550 mm 1 80°C PP Probe holders with 3/4" probe attachment without protection These can house conductivity probes with threaded 3/4" G. Attachment with output cable or IP67 connector. Counter-flange Int. Diameter Ext. Diameter Attachment Material No. of probes Max Temperature Material Immersion probe holder Immersion No. of probes Max Temperature Material PI G PI G Code 9900100131 Floating 1 40°C PVC B PI G Code 9900100132 2m anchorage arm - 40°C PVC FER for quick removal FER 65 mm Code 9900100133 140 mm 40°C 4 holes Ø 6 mm > > > innovation technology future 29 Probe Accessories Cables, buffer solutions and probe accessories probe holders Probe Accessories Immersion probe holder Immersion No. of probes Max Temperature Max Pressure 1/h Min - Max PIA PVC PIA PVC 400 400 mm PIA PVC 800 800 mm Code 9900100151 1 40°C Code 9900100152 1 40°C 2÷6 100÷600 2÷6 100÷600 Immersion probe holders with spray cleaning These special probe holders can be connected with a cleaning liquid injection unit. Regular cleaning of the probe ensures linearity and stability of the measurement over time, preventing the need for timeconsuming manual intervention. PSS 7 Single PSS 7 PSS 7A Tap probe holder Immersion No. o probes Max Temperature Max Pressure PSS 7 Single 400 mm PSS 7 800 mm PSS 7A 800 mm Code 9900103021 1 40°C 6 bar Code 9900103008 1 40°C 6 bar Code 9900103010 1 40°C 6 bar Tap probe holders Tap probe holders are used for inline measurements where part of the sample is re-directed from the main pipe to the probe holder. The water can be drawn off into the sampling circuit at a pressure of 6 bars. > > > 30 seko water & industry control and measuring instuments Probe Accessories Outflow probe holder Outflow probe holders for conductivity probes Bypass probe holder for conductivity probe model CTK1, 5 and 10 Made of black PVC with 3/4" mechanical connection and 1" GAS IN/OUT hydraulics. OUTFLOW SECTION (PSS-COND-T) Code 0000126035 PSS 3 SPP SPP FIL Pressurized probe holder Connection to the process Probes attachment Max Temperature Max Pressure Material PSS 3 1/2" G.M. SPP 1" G.F. SPP FIL 3/4" or 1" 1/4 G.M. Code 9900106670 PG 13,5 or Ø 12 mm Code 9900100134 PG 13,5 Code 9900100135 PG 13,5 60°C 7 bar PVC 60°C 16 bar PP + PVC 80°C 16 bar PP Pressurized probe holders Pressurised probe holders are used to immerse the probe directly into the pipe where the sample to be measured passes. The probe must always be positioned vertically or slanting in the direction of the flow at a maximum of 45°. The probe holder connection line must be fitted between two isolation valves (input and output) in order to permit the prevention of the flow during maintenance of the probes. > > > innovation technology future 31GPL Ghostscript 9.55.0