User Manual for OHNIYOU models including: GLX020-DB Caged Ceiling Fans with Lights and Remote, GLX020-DB, Caged Ceiling Fans with Lights and Remote, Ceiling Fans with Lights and Remote, Fans with Lights and Remote, Lights and Remote, Remote
Ohniyou Caged Ceiling Fans with Lights and Remote, 20" Farmhouse Low Profile Indoor and Outdoor Bladeless Ceiling Fan for Kitchen, Bedroom, Dining Room
OHNIYOU ENERGY SAVING LIFE Ceiling Fan With Light User Manual 020 1. To reduce the risk of electric shock, turn off the electricity to the fan at the main fuse box or circuit panel before beginning. 2. All wiring must be in accordance with the local electrical codes or National Electrical Code. Electrical installation should be performed by a qualified licensed electrician. 3. To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 4. Make sure the installation site you choose allows clear space for the blades to rotate and at least 7 feet(2.13 meters) of clearance between the floor and the fan blade tips. The fan should be mounted so that the tips of the blades are at least 18 inches (45.72 centimeters) from walls or other upright structures. 5. WARNING: To reduce the risk of fire, electric shock, or personal injury, mount fan only to an outlet box marked acceptable for fan support and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. 6. The outlet box and ceiling support structure must be securely mounted and capable of supporting at least 45KGs. 7. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan. 8. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning. 9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipmentgrounding conductor on one side of the outlet box. 10. Electrical diagrams are for reference only. 11. The fan is suitable for indoor and covered outdoor. This manual is designed to make it as easy as possible for you to assemble, install, operate and maintain your ceiling fan. Materials WARNING Before assembling your ceiling fan, refer to section on proper method of wiring your fan (page 10). If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician. Wiring outlet box and box connectors must be of type required by the local code. The minimum wire would be a 3-conductor(2-wire with ground) of the following size: Installed Wire Length Up to 50 ft Wire Size A.W.G 14 50-100 ft 12 NOTE: Place the parts from the loose parts bags in a small container to keep them from being lost. If any parts are missing contact your local retailer. Package Includes Check to see that you have received the following parts: 1 ALL OFF F LIGHT ON/OFF R 3 2 4 FAN/OF F 1 5 6 1H 2H 4H 9 10 DC motor Control Driver Model:XH-0SFS-24V-84 433 Input:AC110-265V 50/60HZ LED OUT:50-200W 220816 C 11 2 4 5 8 3 6 7 1. Mounting Bracket 2. Canopy 3. Canopy Screws 4. 4 & 8 inches Downrod 5. Cross Pin 6. Clamp Pin 7. Ceiling Fan Body 8. Hand-held Remote 9. Wood Screws 10. Expansion Screws 11. Receiver 1 2 1. 8 6 Re-install pin into extended downrod, and fixed downrod to the hanging bracket 1. Carefully lift motor assembly and place downrod onto the ball. Install pin into the downrod, and two fixed screw 2. Adjust the length of the safety cable attach the safety cable from fan unit to hook, secure by looping zip tie through safety cable and hook. Tighten zip tie securely 3 Plug the wires of the controller with the corresponding color of the fan, and then connect the other section of the controller to the zero wire and the fire wire, and then connect the ground wire. Motor Wire DC motor Control Driver Model:XH-0SFS-24V-84 433 Input:AC110-265V 50/60HZ LED OUT:50-200W 220816 C Ground Wire Zero wire Fire wire Light Wire INSTALL THE LIGHT BULB 1. Make wiring connections. please refer to the figure right for the electrician between fan motor and light bulb. 2. Rotate the 5*E26 bulb into the lamp slot. 4 4-E26 × × × 5 6 Troubleshooting WARNING For your own safety turn off power at fuse box or circuit breaker before trouble shooting. Trouble 1. FAN WILL NOT START Probable Cause 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connections in the switch housing. 3. Dead battery in remote control. 4. Reversing switch in neutral position. Suggested Remedy 1. Check main and branch circuit fuses or circuit breakers. 2. Check line wire connections to fan and switch wire connections in the switch housings. CAUTION: Make sure main power is turned off ! 3. Replace with new battery. 4. Make sure reversing switch position is all the way to one side. 2. FAN SOUNDS NOISY 1. Loose screws in motor housing. 2. Wire connectors inside housing rattling. 3. Motor noise caused by solid state variable speed control. 1. Check to make sure all screws in motor housing are snug (do not over-tighten). 2. Check to make sure wire connectors in switch housing are not rattling against each other or against the interior wall of the switch housing. CAUTION: Make sure main power is turned off! 3. Some fan motors are sensitive to signals from solid-state variable speed controls. Solid-state control are not recommended, choose an alternative control method. 3. FAN WOBBLES EXCESSIVELY 1. Setscrew in downrod support is loose. 2. Setscrew in downrod/hanger ball assembly is loose. 3. Hanger bracket and/or ceiling outlet box is not securely fastened. 1. Tighten both setscrews securely in downrod support. 2. Tighten the setscrew in the downrod/hanger ball assembly. 3. Tighten the hanger bracket screws to the outlet box, and secure outlet box. 7 Maintenance 1. Periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning use only a soft brush or lint free cloth to avoid scratching the finish. Abrasive cleaning agents are not required and should be avoided to prevent damage to finish. CAUTION Do not use water to cleaning your ceiling fan. It could damage the motor or the finish and create the possibility of electrical shock. Warranty Dear Customer: OHNIYOU warrants that this product is free from defects in materials and workmanship for a period of 1 years from the day of purchase. If the product has been misused, damaged by accident or in any other way of improper use, this warranty becomes void. Please feel free to contact us: ohniyou@ledphy.com 8WPS 文字