Instruction Manual for BLINKCAST models including: Flexion 6 Led Single Colour Lighthead, Flexion, 6 Led Single Colour Lighthead, Single Colour Lighthead, Colour Lighthead, Lighthead
FX6 - Blue (12~24VDC) - Cell2
86-M08910-0001.0 SINGLE COLOUR 6 LED SINGLE COLOUR LIGHTHEAD Wiring To Chassis Ground:........................................... BLACK To+VDC for Warning Mode (fuse @ 1A):.............. RED Default Flash Pattern - FP#2 Single [2Hz] To+VDC for Warning Mode (fuse @ 1A):......... WHITE Default Flash Pattern - FP#1 Double [2Hz] To+VDC for Warning Mode:.................RED+WHITE Default Flash Pattern - FP#18 Steady Scene For Synchronization and Flash Pattern:........YELLOW Connect YELLOW wire of all lightheads together for synchronization. (All lightheads should be set to the same Flash Pattern) 117.4mm (4.62" ) Operation For Flash Pattern Selection: Each Warning Mode may select and save one Flash Pattern. While activating a Warning Mode, momentarily apply YELLOW wire to +VDC: · Once to the next pattern. · Quick three times to FP#1 (refer to Flash Pattern Chart) Flash Pattern (Single Colour) 1 Double [2Hz] 2 Single [2Hz] 3 Triple [2Hz] Shortcut Setting for Steady EF (External flasher): 4 This shortcut allows quick changing of trigger wires setting to each colour with Steady EF pattern all at 5 one time. Momentarily apply YELLOW wire to +VDC for 3~4 seconds (visual feedback: ONOFF ON) while activating any warning mode. Colour mode and Flash Pattern of each warning mode will be 6 set to: 7 Warning Mode 1 = Colour 1, FP#6 Steady EF 8 Warning Mode 2 = Same Colour mode, FP#21 OFF Warning Mode 3 = Same Colour mode, FP#21 OFF 9 10 Setting Mode 11 Quad Random Steady EF* Single Double Triple Quad Quint [2Hz] [SAE][CA13] [SAE] [SAE] [SAE] [SAE] The following settings will require user to enter SETTING MODE to operate; to enter: 12 Mega 1. Power off the unit completely and power up by applying +VDC to RED (or WHITE or RED+WHITE) and YELLOW wires simultaneously. 13 Giga 2. Remove YELLOW wire from +VDC to enter SETTING MODE. Lighthead will then flash in 14 Ultra [SAE] low-power while in SETTING MODE. 3. To save and exit the setting, simply disconnect the power after operation. 15 Single-Quad 16 Singe H/L For Simultaneous or Alternating Synchronization: To change Group, while in setting mode, momentarily apply YELLOW wire to +VDC for 3~4 seconds. 17 Single-Triple-Quint the lighthead will display short flashes: 18 Steady Scene · Single flash · Three flash Set by BlinkCast Programmer only. · Five flash · Seven flash Simultaneously = Group 1 = Group 2 = Group 4 = Group 7 Alternately · Double flash = Group 5 · Four flash = Group 3 · Six flash = Group 6 · Eight flash = Group 8 NOTE: · Lightheads of the same Group will flash together. · Lightheads of the Group 1 & Group 5 will flash alternately. 19 Cruise 20 Sweep Single TA 21 OFF * For use with external flash controller. Reset to Factory Default Settings: While in setting mode, apply YELLOW wire to +VDC for more than 5 seconds. The lighthead will display fast short flashes to signify restoring successfully. BlinkCast Ready This product can be configured ideally by using BlinkCast Programmer with desired Flash Pattern, Group (Phase), and Colour Mode to save your installation time! Contact your sales representatives or see your User Manual of BlinkCast Programmer for detailed information. SINGLE COLOUR 6 LED SINGLE COLOUR LIGHTHEAD Installation Curved Surface / Flat Surface 1. [Curved Surface] Use curvature template to check surface mountability: make sure surface curvature is over 120 degree. Both points can touch: mountable Curvature Template One or no point can touch: unmountable Curvature Template Mounting Surface Mounting Surface 2. Mark and drill a wire passage hole on the mounting surface. Make sure no vehicle parts could be damaged by the drilling process. (Thoroughly deburr hole and use grommet for wire passage hole if needed) 3. Clean and dry the mounting surface with alcohol prep pad provided. (or 50:50 mix of isopropyl alcohol and water) 4. Remove the tape liner from the tape and apply the lighthead to the surface and press it firmly for 30 seconds. Full adhesion and bonding will be achieved after 72 hours at room temperature. 5. [Flat Surface] For best secure installation, it is recommended to always mount lightheads with screws. [Curved Surface] Due to lighthead tension, it is required to always mount lightheads with screws on curved surface. 6. Once secured, apply screw covers onto the lighthead for best aesthetic. (use silicon glue to better scure the screw cover) Prohibition Tape liner Ø3.5mm (0.135in) Screw washer Ø3x12mm Sheet metal screw Screw covers No Pulling No Warping No Bending Inwards Mounting Dimensions 117.4mm(4.62") No bending over 120° Curvature Template 1:1 template Ø15mm(0.59") 1:1 template 120° Max. CUT CUTAdobe PDF library 17.00 Adobe Illustrator(R) 24.0