TRIMIX-RF05A Wireless Remote Control User Manual

I. ELECTRONICS OVERVIEW

This section provides an overview of the electronic components included in the system.

System Components:

Control Box: The central unit with ports for power, USB, and motor connections. It features buttons labeled RESET BUTTON, CONNECT BUTTON, and indicators like LED, WORK STATUS, and LAMP. It also has a SYNCHR port.
Control Box Labels: LED, RESET BUTTON, CONNECT BUTTON, WORK STATUS, LAMP, POWER LINE, USB, SYNCHR.
Remote Controller: A wireless device used to operate the system. It includes buttons for various functions such as TV, ZG, ANTISNORE, HEAD UP, HEAD DOWN, FOOT UP, FOOT DOWN, HIP UP, HIP DOWN, FLAT, and PAIRING.
Power Supply: Converts mains power to the required voltage for the control box.
Specifications: Input: 100-240V ~, 50/60Hz; Output: 29.0V
Motors: Actuators that move the connected mechanism (e.g., bed base). The system supports multiple motors.

The diagram illustrates the connection between the power supply, control box, remote controller, and motors.

II. PAIRING THE WIRELESS REMOTE

Follow these steps to pair the wireless remote controller with the control box.

Step 1: Install Batteries

Push in on the bottom of the remote to release the battery cartridge. Install two AAA batteries into the remote battery compartment and push firmly to close.

Step 2: Initiate Pairing on Control Box

Plug the control box base into a power source. Press the Pairing Button/Program Button on the control box for approximately 1 second. Ensure the Pairing Lamp - White (Third) is flashing.

Step 3: Complete Pairing on Remote

First, press the "SW" button on the remote until the backlight LED starts flashing, then release it. Second, press the "HEAD UP" button. Continue to hold the "HEAD UP" button until the backlight LED on the remote lights up continuously, then release it. This indicates the remote is pairing.

Pairing is completed when the Pairing Button/Program Button on the control box and the backlight LED on the remote stop flashing, and the control box emits a "DI" sound from the buzzer.

If the remote functions cannot be operated after pairing, repeat the pairing process.

III. FUNCTIONAL OPERATING FOR WIRELESS REMOTE

This section details the functions controllable via the wireless remote.

MARK	STEP 1	STEP 2	FUNCTION	DESCRIPTIONS
[Image: Wireless remote control with buttons labeled TV, LED, ZG, SW, UP, DOWN, FLAT R, etc.]	Press "SW" in 3s until the backlight LED flashing and then press the "BUTTON" in STEP 2	TV	MEMORY POSITION	The backlight LEDs are all OFF before operating. Press (TV, ZG) until the backlight LED is lighting and the memory position is completed. When the backlight LED is lighting and press again, clear the corresponding memory position. TV & ZG have the memory position.
		ZG	MEMORY POSITION	(See above description for TV)
			ANTISNORE	New ANTI-SNORE preset position and five minutes will be reset.
			HEAD DOWN	FUNCTIONS IN CIRCLING	Head up and down functions in circling.
			BACK DOWN	FUNCTIONS IN CIRCLING	All bed base functions up and down in circling.
			FOOT DOWN	FUNCTIONS IN CIRCLING	Foot up and down functions in circling.
			HIP DOWN	FUNCTIONS IN CIRCLING	Hip up and down functions in circling.
			FOOT UP	SHORTCUT KEY	Foot down tilt (Music position).
			HIP UP	SHORTCUT KEY	Head down tilt (Leg relaxing position).
			HEAD UP	PAIRING	Pairing the remote and control box.
			FLAT	FORCED RESET	The bed will be in FLAT position when the bed is breakdown.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter.

USER'S MANUAL