Rave SL-3454

Introduction

Thank you for purchasing this product. Please read this user guide for safety and operations information before using the product. Keep this manual for future reference. Please handle with care after receiving the unit and check the attachments listed in this document after opening the carton.

Box Contents

• 1 x Laser Light
• 1 x Power Supply
• 1 x User Manual
• 1 x Tripod
• 1 x Remote Control

Warnings

• Do not expose the human eye direct to laser beam.
• Before using this unit make sure the power supply is grounded.
• This unit is intended for indoor use only and should be kept away from water, moisture and excessive movement. The working temperature of this unit is 18°-30°C, do not use this unit continuously over 4 hours, otherwise it shortens the lifetime of the unit.
• Do not remove or break the warranty label, otherwise it voids the warranty.
• Product installation and maintenance should be undertaken by a professional.

⚠ WARNING! KEEP BUTTON BATTERIES OUT OF REACH OF CHILDREN

• If swallowed a lithium button battery may lead to serious or fatal injury in as little as 2 hours, due to chemical burns and potential perforation of the oesophagus.
• Non-lithium button batteries can cause serious injuries if they are swallowed or placed inside any part of the body.
• All button batteries must be kept away from children regardless if they are new or used.
• If you suspect your child has swallowed or inserted a button battery immediately call the 24-hour Poisons Information Centre on 13 11 26 (Australia) or 0800 764 766 (New Zealand) for fast, expert advice.
• If your child is having difficulty breathing contact 000 (Australia) or 111 (New Zealand).
• Dispose of used button batteries immediately and safely out of the reach of children. A battery can still be dangerous even when it can no longer operate the device.
• As soon as you have finished using a button battery, put sticky tape around both sides of it. This will make it harder for children to swallow the button battery and avoid the risk of the battery catching fire.
• Immediately dispose of button batteries immediately out of reach of children, or recycle using a child resistant container and take used cells to your local battery collection centre.

Installation

1. Before use, please make sure power voltage is as per the one marked on the unit.
2. This product should be installed by professional to make sure it is fixed safely and have adjusted suitable display angle.
3. When installing this unit, please make sure there is nothing flammable or explosive within 0.5 meters of the unit. Make sure there is 15 mm distance between the unit and the wall. Please make sure to use safety rope which can support tenfold weight of the unit to assist fitting.

Functions

Sound Activated: The changes of the laser pattern are controlled by sound, that is, the rhythm of the sound controls the effect of the changing laser patterns. Turn the sensitivity knob in the clockwise direction to increase the unit's sensitivity to sound, Turn the knob in the counterclockwise direction to decrease. The laser diode will automatically turn off after 4 seconds when the unit detects no further music playing.

Auto Active: Auto cycles the built-in programs without being controlled externally. The unit has no laser OFF.

Laser Remote

The remote control has the following functions:

• Power: Close or open the light.
• Speed: Controls the speed of the laser patterns. Options include 1) Faster, 2) Fastest, 3) Normal.
• Colour: Multi-colour change.
• Auto Music: Switches between auto mode and music-controlled mode.
• Pattern: Selects different laser patterns.
• Mode: Controls the direction or state of patterns. Options include 1) Clockwise, 2) Stop, 3) Counterclockwise, 4) Normal.

[Diagram: Laser Remote Control Layout showing numbered buttons for Power, Speed, Colour, Auto Music, Pattern, and Mode.]

Front Panel

The front panel features:

• 1. Infrared Receiver
• 2. Laser Aperture

[Diagram: Front Panel of the Laser Show System showing the Infrared Receiver and Laser Aperture. Includes a warning: "Visible or invisible radiation. AVOID EXPOSURE -- Laser radiation is emitted from this aperture."]

Rear Panel

The rear panel features:

• 1. Fan
• 2. Sound Active Modulation Knob
• 3. Auto/Music Active Switch
• 4. Power Input Connector
• 5. Power Supply Switch

[Diagram: Rear Panel of the Laser Show System showing the Fan, Sound Active Modulation Knob, Auto/Music Active Switch, Power Input Connector, and Power Supply Switch.]

Troubleshooting

Specifications

Distributed By

TechBrands by Electus Distribution Pty. Ltd.

320 Victoria Rd, Rydalmere NSW 2116 Australia

Ph: 1300 738 555

Int'l: +61 2 8832 3200

Fax: 1300 738 500

Website: www.techbrands.com

Made in China