User Manual for Galaxy Equipment models including: 177GB440 Blender with Toggle Controls, 177GB440, Blender with Toggle Controls, Toggle Controls, Controls

WebstaurantStore

PDF preview unavailable. Download the PDF instead.

galaxy 177gb440 manual
User Manual

Blender with Toggle Controls

Model: 177GB440

This product is designed for light-duty, low-volume operations.

12/2022

Please read and keep these instructions. Indoor use only.
- 1 -

User Manual

IMPORTANT SAFETY INSTRUCTIONS
When using electrical equipment, basic safety precautions should be followed to reduce the risk of burns, electrical shock, fire, or injury to persons.
READ ALL OF THE INSTRUCTIONS BEFORE USING THIS EQUIPMENT.

1. CAUTION: Blades are sharp. Handle

9. Do not use outdoors.

carefully.

10. Secure the lid before turning the blender on.

2. Never remove parts or clean the blender unless it is unplugged from the electrical outlet.

11. To prevent damage to blender, container, or cutter assembly, DO NOT move or shake blender while in operation. If blending

3. Do not immerse the blender in water or other

action stops during operation turn blender

liquid. Doing so can result in electrical shock.

OFF, remove container from base, remove

4. Avoid contact with moving parts while operating the blender.

container cover, and use a thin rubber spatula to push mixture towards cutters.

5. Ensure you are using this blender on a properly grounded outlet. This blender comes with a 120V NEMA 5-15P plug. If unsure of your electrical configuration,

12. Do not place hands or utensils in the blender jar while it is operating. Doing so can cause severe personal harm and/or damage to the blender.

contact a professional electrician before

13. When blending hot liquids (anything over

operating.

100°F), remove the center piece of the jar

6. Do not use the blender if the cord or plug is damaged.

and start on the lowest speed setting. Do not stand directly over the blender while in use.

7. Keep the power cord on the counter in which 14. Ear protection is recommended if blending

the blender is being used. Do not allow it to

for long periods of time.

hang over the counter or come in contact

15. Never leave blender unattended while

with liquids or hot surfaces.

operating.

8. This blender is not intended for use by children or individuals with impaired mental and/or motor skills. Individuals who lack experience operating a blender need supervision during use.

16. Contact the nearest authorized service agency for repair.
SAVE THESE INSTRUCTIONS

TECHNICAL INFORMATION

Model No.

Capacity

Voltage

177GB440

44 oz.

120V

Wattage
400W

Hertz
60Hz

Horsepower
1/2

- 2 -

User Manual
OPENING & INSTALLATION INSTRUCTIONS
· Inspect blender for any damage such as cracks or dents in base and container. · Remove all plastic wrap and packaging material before use. · Do not install blender next to or above source of heat, such as an oven or radiator.
This could cause the blender to operate improperly and could shorten life of electrical parts. · Install blender on a level countertop surface. · Plug into a grounded 120V outlet, free of other appliances and equipment. · Outlet should be located so that the plug is accessible when microwave is in place.
CLEANING INSTRUCTIONS
GENERAL CLEANING
1. Remove the container from the blender base and remove the jar cover. 2. Add cleaning solution to the container.
(Non-sudsing detergent and hot water (less than 115°F). 3. Scrub and flush out the container interior, cover, and filler cap to remove food
residue and empty the container. 4. Fill container 1/4 full with fresh cleaning solution and place it on the base. 5. Replace the cover on the container and run the blender on 2 - HIGH speed for 2
minutes. 6. Repeat steps 3 & 4 using clean rinse water (95°F). 7. Wipe down the container, filler cap, and cover with a soft cloth or sponge,
dampened with fresh cleaning solution. 8. Wipe the exterior of the base with a damp cloth or sponge.
The base contains electrical components DO NOT immerse in water or cleaning solution. DO NOT use a high-pressure washer or dishwasher to clean the base. 9. Allow all parts to air dry.
SANITIZING
1. Wash container as instructed above. 2. Fill container 1/4 full with preferred sanitizing solution and place on base. 3. Replace cover and filler cap and run on 1 - LOW speed for 2 minutes, then empty
the container. 4. Wipe the container exterior with a soft cloth or sponge dampened with sanitizing
solution. 5. Remove any remaining moisture from cutter assembly by placing empty container
on base and running on 2 - HIGH speed for 10 seconds. 6. Allow all parts to air dry.
NOTE: DO NOT rinse container, cover, or filler cap after sanitizing. 7. When ready to use, rinse with clean water.
- 3 -

User Manual
CONTROLS
· 2 - HIGH
(19,000 RPM)
· 0 - OFF
· 1 - LOW
(16,000 RPM)
OPERATION INSTRUCTIONS
WARNING: ELECTRICAL SHOCK & CUT HAZARD
· Failure to follow these instructions can result in broken bones, cuts, fire, or electrical shock.
· DO NOT put hands, spoons, or other utensils into container while blending.
· ALWAYS place cover on container before blending.
Before using the blender for the first time, wash the container, cover, and cutter assembly using the Cleaning Instructions on page 3. Do not put the cutter assembly in the dishwasher, as the water pressure and temperature may damage components. 1. Place the blender on a clean, dry, and level surface. 2. Make sure that the control pane switch is set to 0 - OFF. 3. Plug the blender into a grounded 120V wall outlet, free of other appliances. 4. Place the ingredients into the container.* 5. Place the container onto the base, ensuring it rests securely. 6. Place the cover and filler cap on the container. 7. Move the selector switch to the desired speed.* 8. When blending is complete, set the selector switch to the 0 - OFF position.
DO NOT remove the container from the base until the unit has stopped. *See Professional Blending Techniques on page 5 for optimal blending operations.
- 4 -

User Manual
PROFESSIONAL BLENDING TECHNIQUES
ALL PRODUCT TEMPERATURES
· Use a sufficient amount of liquid to ensure that the mixture is fluid and free-running at all times.
· Pour the liquid into the container FIRST. · Cut solid ingredients into pieces no larger than 1" cubes. · DO NOT blend maximum volume all at once. If making a large recipe, add the
ingredients to container in batches. · DO NOT overfill the container with product. This may prevent the blender from
processing the product properly. · Process dense foods or thick mixtures in small batches, and remember that the
volume of the product normally increases during processing. · Use the filler cap to add liquids to the container while the unit is running.
COLD PRODUCT
· ALWAYS place the cover and filler cap on the container before blending. · DO NOT use blender to crush large ice cubes. The blender is designed to crush
small ice cubes or partially crushed ice for best results. · The blender takes approximately 30-60 seconds to fully crush ice when using small
cubes in combination with a liquid base. · Chunks of frozen fruit (<1" cubes) can be added to milk or fruit juice to produce a
sherbet or smoothie-style beverage.
HOT PRODUCT
WARNING: BURN HAZARD
· Failure to follow these instructions can result in burns.
· DO NOT exceed 1 Quart (1 Liter) of content when blending hot product. · ALWAYS place the cover, but remove the filler cap before blending to prevent
pressure buildup inside container. · DO NOT stand with your face or hands directly over the container when operating
the blender where steam may be released. · ALWAYS begin on 1 - LOW speed and then, if needed, select 2 - HIGH speed to
add a column of air in the center of the container.
- 5 -

User Manual

REPLACING THE KNIFE ASSEMBLY
WARNING: CUT HAZARD
· Failure to follow these instructions can result in cuts.

The blender knife assembly should be checked daily for worn, loose, or damaged blades. If the cutter unit assembly is worn or damaged, it should be replaced immediately to prevent injury or contamination of food product.
1. Loosen the collar on the bottom of the blender jar. 2. Remove the blender knife assembly and gasket from the bottom of the container. 3. Place the gasket on the new blender knife assembly, then install the new cutter unit
assembly in the bottom of the container. 4. Securely tighten the collar onto the bottom of the container. 5. The rubber clutch disc on the blender base has reverse threads.
To replace, remove by turning it clockwise. Then install the new disc, turn it onto the motor shaft counter-clockwise.

EXPLODED VIEW & PARTS LIST

PART

ITEM #

DESCRIPTION

1

A

1 177PGB440LPC

Lid Pour Cap

2

2 177PGB440LC

Lid Cover

3

N/A

Blender Jar

4 177PGB440GSK

Gasket

3

B

5

N/A

Knife Assembly

6 177PGB440BC

Actuator Clutch

4

7 177PGB440JCB

Jar Container Base

5

C

8

N/A

9

N/A

Blender Base

6

Control Panel Switch

7

A 177PGB440LID Complete Lid Assembly

8

B 177GBB440JAR Complete Jar Assembly

9

C 177PGB440KNF Complete Knife Assembly

- 6 -


Adobe PDF Library 17.0 Adobe InDesign 18.0 (Macintosh)