Home | Commercial Door Hardware | Corbin Russwin
P65warnings.ca.gov
Installation Guide for Corbin Russwin models including: FE6600, BL6600, MP6600, FE6600 Series EcoFlex Multi Point Lock Platform, FE6600 Series, EcoFlex Multi Point Lock Platform, Multi Point Lock Platform, Point Lock Platform, Lock Platform, Platform
File Info : application/pdf, 2 Pages, 312.21KB
DocumentDocumentInstallation & Wiring Instructions FE6600/BL6600/MP6600 Series End-of-Line Resistors for EcoFlex® Electrified (NAC only) and Integrated Wired (Access 600, SE LP10) Multi-Point Locks ED 1 Description U The EcoFlex multi-point lock platform, including Corbin Russwin Access 600 and SE LP10 Integrated Wired multi-point locks, is now available with internal end-of-line resistors for N comprehensive monitoring of the circuit between the access control panel and lock. InI tegrating the end-of-line resistors into the lock not only eliminates the risk of undetected tampering, but reduces installation costs, simplifies specification, and offers the assurance of T a factory installed and tested product. 2 N EAC Resistor Configurations · R01: Mercury/Lenel Standard 1K/2K · R03: Software House Standard 1K/2K O · R04: AMAG 4-State supervision NOTE: End-Of-Line Resistor harnesses are designated by blue shrink-tubing. C ID OEM Description Tamper Normal Tamper Normal REX Short Open Secure Alarm DPS Short Open Secure Alarm R01 Mercury/Lenel Standard 1K/2K NO 0 2K 1K NC 0 1K 2K S R03 Software IHouse Standard 1K/2K NO 0 1K 500 NC 0 1K 2K DR03 AMAG 4-State Supervision NO 0 10K 5K NC 0 4.7K 9.4K WARNING CTohrbisipnroRduuscstwciann, Ienxcp.ose you to lead 22w5hiEcphiissckonpoawlnRtooatdhe state of California Betorlcinau, CseTc0an6c0e3r7anUdSbAirth defects or other PFahrgxeoo:pnt8rooe0d:w08uw-c04wt04iv.-P7e56-h456a3w7r-m1a3r4.n5Fi5no8gr sm.coar.geoinv.formation www.corbinrusswin.com For installation assistance contact Corbin Russwin 1-800-543-3658 · techsupport.corbinrusswin@assaabloy.com Copyright © 2017, 2020, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited. FM472 8/20 The ASSA ABLOY Group is the global leader in access solutions. Every day we help people feel safe, secure and experience a more open world. 3 Configure DIP Switch Settings IMPORTANT: This product is built and factory tested to the configuration specified. Any change to the 3-position DIP-switch settings located at the bottom of the mortise lock body must be made prior to lock installation. Handing 12 3 DIP Switch RH & RHR LH & LHR Check Polarity: Verify + (red wire) RX Output Normally Open Normally Closed Actuator Operation Fail Safe Fail Secure R01 1K/2K Mercury/Lenel Compatible 1K 1K 1K 1K NO R03 Software House Compatible NC 1K 1K NO 1K 1K NC R04 AMAG 4-State Supervision 10K 10K NO 4.7K 4.7K NC Corbin Russwin, Inc. 225 Episcopal Road Berlin, CT 06037 USA Phone: 800-543-3558 Fax: 800-447-6714 www.corbinrusswin.com For installation assistance contact Corbin Russwin 1-800-543-3658 · techsupport.corbinrusswin@assaabloy.com Copyright © 2017, 2020, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited. FM472 8/20