User Guide for msi models including: G52-S4052X1, S405-CG480-S5063, CG480 AI Server, CG480, AI Server, Server
Jun 6, 2025 — Refer to the User Guide for proper cable routing instructions. 6. Install GPU Card. 8. Loosen the screws on the riser bracket to remove the filler panels. 9 ...
CG480-S5063 QUICK START GUIDE Top View 1 2 CPU 0 3 CPU 1 4 G52-S4052X1 Install CPU and Heatsink 1 3 x4 Unlocked 5 2 Pin 1 Pin 1 4 Cut-corner E2A: Lower E2B: Upper 7 #1 x4 Locked 6 Important Please refer to the following table for the corresponding CPU carrier. Torque Screwdriver Setup Screw Head: Torx T30 Screws #1-4: 0.904 N·m* (+/-10 %) *0.904 N·m = 9.2208 kgf·cm = 8 lbf·in CPU Package Type Thin Package Granite Rapids- SP XCC CPU Package Name CPU Carrier Code E2A Thick Package Granite Rapids- SP HCC/ LCC Sierra Forest- SP E2B Memory The server board supports 32 DDR5 DIMM slots, compatible with RDIMMs and MRDIMMs. DIMM Type RDIMM MRDIMM Max Frequency 6400 MT/s (1DPC), 5200 MT/s (2DPC) 8000 MT/s (only support 1DPC) Max Capacity per DIMM 256GB 64GB H G F E A B C D Slot 1 Slot 2 Slot 1 Slot 2 Slot 1 Slot 2 Slot 1 Slot 2 Slot 2 Slot 1 Slot 2 Slot 1 Slot 2 Slot 1 Slot 2 Slot 1 CH4 CH5 CH6 CH7 CPU CH0 CH1 CH2 CH3 6 5 No. Description 1 (3+1) 3200W CRPS PSU 2 PCIe Switch Board 3 Motherboard No. Description 4 5 x 8080 Hot-Swap System Fans (upper, for GPU) 5 5 x 8080 Hot-Swap System Fans (bottom, for CPU) 6 20 x Hot-Swap E1.S drive bays (PCIe 5.0 x4 NVMe) CPU and GPU CPU: Dual Intel® Xeon® 6700E- series, 6500P-series and 6700P-series processors, TDP up to 350W. GPU: Max eight double wide PCIe GPU cards, TDP up to 600W. Safety Precautions Power Off Before Servicing: Always power off the server and unplug the power cord before installing or removing components. ESD Protection Required: Use an ESD wrist strap or anti-static mat when handling internal components to prevent electrostatic discharge damage. IMC7 IMC6 IMC5 IMC4 IMC0 IMC1 IMC2 IMC3 IMC# IMC7 IMC6 IMC5 IMC4 IMC0 IMC1 IMC2 IMC3 Channel H G F E A B C D Chan 7 Chan 6 Chan 5 Chan 4 Chan 0 Chan 1 Chan 2 Chan 3 DDR5 Qty. H1 H2 G1 G2 F1 F2 E1 E2 A2 A1 B2 B1 C2 C1 D2 D1 1 V C 4 V V P V V V V V V U V V V V V V V V 8 VV VV VV VV VV VV VV VV 12 V VVV VV VV VVV V 16 VVVVVVVV VVVVVVVV "V"indicates DIMMs are populated with DDR5. Important There should be at least one DDR5 DIMM per socket. DDR5 memory configurations requires same DIMM types, ranks, speeds, and densities. Mixing vendors, non-3DS/3DS RDIMMs, 9x4 RDIMMs, or x8/x4 DIMMs is not allowed. Mixing DIMMs with different operating frequencies is not validated. When frequencies differ, the system defaults to the lowest common speed. Install PCIe Add-in Card 1. Disconnect all cables from the PCIe switch board and disconnect the CAM riser from the motherboard, then remove the board from the system. 2. Unscrew the rear-side screw and slide out the PCIe tray by pressing the release switch. 3. Remove the fixing panel, filler panels, and PCIe bracket from the tray. 2 1 3 4. Insert the PCIe card into the connector and secure with fixing panel and screw. 5. Reattach the PCIe bracket and and press down firmly until it clicks -- the auto-lock plunger will engage. 6. Reinstall the PCIe assembly into the chassis. 7. Reinstall the PCIe switch board and reconnect cables. Refer to the User Guide for proper cable routing instructions. 4 5 6 Install GPU Card 8. Loosen the screws on the riser bracket to remove the filler panels. 9. Attach the mounting bracket to the GPU card by tightening the screws. 10. Align the GPU card with the connector, and insert it until it is fully seated. 11. Tighten the screws to securely fix the PCIe add-in card in place. 4 1 2 3Adobe PDF Library 17.0 Adobe InDesign 20.1 (Windows)