VIVO Black Electric Single Motor Desk Frame

Warnings

⚠️ WARNING! If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. VIVO cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

ELECTRICAL SAFETY INSTRUCTIONS

THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.

• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.

⚠️ WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

Package Contents

• A (x1) Telescopic Crossbar
• B (x1) Sync Rod
• C (x1) Cable Management Tray
• D (x2) Foot
• E (x2) Side Bracket
• F (x1) AC Adapter
• G (x2) Hook
• H (x1) Motorized Leg
• I (x1) Leg
• J (x1) Power Cable
• K (x1) Controller
• S-A (x16) M6x12mm Bolt
• S-B (x10) 7/8" Screw
• S-C (x2) 3/4" Screw
• S-D (x4) M4x6mm Screw
• S-E (x3) Cable Clip
• S-F (x8) Rubber Pad
• S-G (x1) Allen Key
• S-H (x3) Soft Pad

Tools Needed

• Phillips Screwdriver
• Drill

DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury. (Max Capacity: 176lbs / 79.8 kg)

Assembly Steps

STEP 1

Loosen the two set screws on the telescopic crossbar (A) using the Allen key (S-G). Adjust the crossbar length to suit the desktop. Retighten all screws. NOTE: Make sure adjusted length of the telescopic crossbar is no more than 61" (155cm).

Diagram Description: Visual representation of loosening set screws on the telescopic crossbar with an Allen key and adjusting its length.

STEP 2

Attach the telescopic crossbar to the legs (H, I) as shown using M6x12mm bolts (S-A), and tighten with the Allen key (S-G). NOTE: Insert all necessary screws into holes before tightening.

Diagram Description: Visual representation of attaching the telescopic crossbar to the two legs using M6x12mm bolts and tightening with an Allen key.

STEP 3

Attach the side brackets (E) to both ends of the frame using four M6x12mm bolts (S-A). Tighten with the Allen key.

Diagram Description: Visual representation of attaching the side brackets to the ends of the assembled frame using M6x12mm bolts.

STEP 4

Place frame upside down on desktop and drill pilot holes for screws. Use a 3/32” or 3mm bit, and drill holes to a depth of 3/8" (10mm).

Diagram Description: Visual representation of the frame placed upside down on a desktop, with a drill creating pilot holes for desktop attachment.

STEP 5

Place the feet (D) on the legs as shown. Insert and tighten bolts (S-A) using the Allen key.

Diagram Description: Visual representation of attaching the feet to the bottom of the legs using bolts and an Allen key.

STEP 6

Position the frame upright. Loosen the knobs on the sync rod (B) and extend the hex shaft. Insert hex shaft into the leg (I), making sure the red bumper makes contact with the leg. While holding the hex shaft with one hand, extend sync rod onto the shaft of the motorized leg, making sure the rod makes contact with the red bumper on the motor shaft. Tighten both knobs.

CAUTION: To avoid injury, at least two people should turn the frame upright.

Diagram Description: Visual representation of connecting the sync rod and hex shaft between the two legs, ensuring red bumper contact on both sides.

STEP 7

Attach hooks (G) to cable management tray (C) using M4x6mm screws (S-D) with a Phillips screwdriver. Hang the tray onto the telescopic crossbar and tighten knobs to secure.

OPTIONAL: Remove paper backing from soft pads (S-H) and stick them to the inside and top of hooks (G).

Diagram Description: Visual representation of attaching hooks to the cable management tray, hanging the tray on the crossbar, and applying optional soft pads.

STEP 8

Connect the AC adapter (F) and motorized leg to the controller (K). Connect the power cable (J) to the AC adapter.

Diagram Description: Visual representation of connecting the AC adapter, motorized leg, controller, and power cable.

STEP 9

Remove the protective film from the adhesive rubber pads (S-F). Position the rubber pads on the side brackets and telescopic crossbar as shown.

Diagram Description: Visual representation of applying adhesive rubber pads to the side brackets and telescopic crossbar.

STEP 10

If you are using a VIVO desktop, Refer to the manual that came with your desktop. If you are not using a VIVO desktop, place the desktop on the frame, and secure the desktop using the 7/8" screws (S-B).

Diagram Description: Visual representation of placing a desktop on the frame and securing it with 7/8" screws.

STEP 11

Attach the controller to the underside of the desktop using 3/4" screws (S-C) as shown. Once controller is installed, cable clips (S-E) can be attached to the desk for cable management. Refer to Controller User Guide for operational instructions.

Diagram Description: Visual representation of attaching the controller to the desktop underside and attaching cable clips for cable management.

STEP 12

If necessary, adjust foot pads to level desk.

Diagram Description: Visual representation of adjusting foot pads for leveling the desk and using a bubble level.

Cautions

• Do not exceed desk weight limit.
• Keep area of vertical motion free of obstacles.
• Keep weight on desk balanced for correct operation and longer life of components.
• Leave enough slack in cables to allow for full range of vertical motion.

Failure to follow these instructions may result in property damage and/or personal injury.