Ethernet Switch

1. Description

The products described in this manual, including but not limited to the products shown, please refer to the actual product purchased. If there are any changes in the appearance of the product and the packing list, please refer to the official product information.

2. Packing list

• Device (Specific model number refer to the product label)
• Power cord (For devices with built-in power modules)
• Power adaptor (For external power products)
• Lugs, screws (Standard rack models only)
• User manual
• Certificate of conformity

3. Switch Installation

The switch supports a variety of installation methods: desktop, rack mount. Please install according to the actual environmental requirements.

Rack type switch installation instructions:

1. Place the device in the cabinet.
2. Align the lugs on each end of the device with the hole bars.
3. Screw mounting.

Rack mounting, as shown in the following figure:

[Diagram showing rack mounting with labels: Front Hole bar, Front hanger, Front panel, Fixed screw, 19in]

Please pay attention to the direction of the switch during installation.

Desktop type switch installation instruction:

The switch can be placed directly on a smooth, flat, and secure desktop. Ensure that the working environment has enough space for ventilation and heat dissipation. The following two points should be noted:

1. Ensure that the physical surface of the switch can withstand a weight of 3 kg or more.
2. Ensure that there is a space distance of 3cm ~ 5cm around the switch, and prohibit heavy objects from being placed on the switch.

Wall Mounting Instructions:

1. Fix the screws on the wall.
2. Place the wall mounting holes on the unit against the screws.

[Diagram showing wall mounting preparation with two screw holes and a device with corresponding mounting holes]

4. Device Connecting

Network Cable

1. When the RJ45 port is 100M rate, use Cat5 and above network cable.
2. When the RJ45 port is 1000M rate, use Cat5E and above network cable.
3. When the RJ45 port is 2.5G rate, use Cat5E and above network cable.
4. When the RJ45 port is 5G rate, use Cat5E and above network cable.
5. When the RJ45 port is 10G rate, use Cat6A and above network cable.

Optical Fiber

1. Fiber must be used with optical modules.
2. The bending radius of the optical fiber cannot be less than 40mm.

Power Cable

1. The distance between the power cord and the network cable should be more than 10cm.
2. Please use AC power cord for AC power supply.

5. Login management

This content applies only to the network management type of product. Please read this help information for first-time application.

Web Management

1. Connect the device and the PC to ensure that the device initialization is complete.
2. Configure the PC's IP address to be on the same network segment as the switch's default IP address.
3. Enter address "http://192.168.1.168" in PC browser. For Light Management Switch, the address is http://192.168.1.1. Press "Enter" to go to the Web management login page. Input the default user name "admin" and password "admin", then press "Enter".

Console Port Management

1. Use the console cable to connect the PC to the console port of the switch.
2. Open the terminal emulation software, establish a connection, select the serial port, and set the communication parameters according to the default configuration of the console port of the switch, as follows:

• Transmission rate: 115200
• Data bit: 8
• Check bit: None
• Stop bits: 1
• Flow control method: None

6. PoE Function

※ This feature is applicable to PoE switches and not to non-PoE switches.

Standard PoE power supply

[Diagram showing a PoE Switch connected to a device via a cable, with the cable's pins labeled for power and data, leading to a PoE-Camera]

Standard PoE power supply includes: Protocol detection, Power pin sequence detection, Power output, Abnormal protection, Link abnormal monitoring.

PoE power protocol includes: IEEE802.3af (15.4W), IEEE802.3at (30W), IEEE802.3bt (60W-90W).

The standard PoE power supply pin is 1,2+/3,6-. Standard PoE++ power supply pin is 1,2,4,5+/3,6,7,8-. Standard PoE switches automatically detect and power standard-compliant PoE devices; non-PoE devices do not power up and only transmit data.

7. Indicator Definition

8. DIP Switches Definition

After-sales Service Letter of Commitment

Within thirty days from the date of sale, if the whole device fails, you can choose to repair, replace or return it.

If performance failure occurs within thirty days to one year from the date of sale (based on the date of purchase invoice and proof of three guarantees (repair, replacement, refund)), the whole machine can be selected for repair or replacement.

Beyond the one-year hardware warranty period, the cost of replacing the hardware will be borne by the user, and the company will not add other costs.

Other service commitments

Provide 7 × 24 hour after-sales support services.

The following are not warranted

Failure or damage to the device (including parts) is not covered by the warranty in the following cases:

1. Accessories supplied by other companies (e.g., power supplies, adapters, etc.) are guaranteed by the manufacturer of the product.
2. The whole device and parts are out of warranty.
3. Failure of or damage to the device was not caused by repair, remodeling or removal by the company's personnel.
4. Failure or damage caused by accidental or human causes, including improper operation, scratches, improper handling, improper movement, improper knocking, improper voltage input, etc.
5. Failure or damage caused by the use of non-genuine or unreleased software.
6. Failures or losses caused by natural disasters such as force majeure (earthquakes, fires, etc.).

Warranty Card