G-TX751 Instructions for Operation
Setting the Operating Controls
This unit operates on a single CR2032, 3-volt battery (not included). To prevent potential damage from battery leakage, remove the battery when the unit is not in use.
Store the controller away from excessive heat or humidity.
This remote-control unit utilizes 66-bit code hopping technology to prevent possible interference from or to other remote units, such as garage door openers, car alarms, or security systems.
Operation Buttons on Transmitter Panel
| Button Number | Function |
|---|---|
| 1 | For Up Door |
| 2 | For Stop Door |
| 3 | For Down Door |
Battery Replacement
Use a CR2032 3V battery.
To replace the battery: Use a screwdriver to remove the screws on the back of the unit (counterclockwise). Open the rear case, remove the old battery, and insert a new one. After installing the battery, close the rear case and secure it by tightening the screws (clockwise) with a tool to complete the battery replacement.
Warning: Chemical Burn Hazard. Keep batteries away from children. See Manual.
General Information
This remote controller is designed to separately control your Garage Door Openers.
Notices and Compliance
Important Note: To comply with FCC RF exposure compliance requirements, no changes to the antenna or device are permitted. Any such change could result in exceeding RF exposure requirements and void the user's authority to operate the device.
Federal Communications Commission (FCC) Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Canada, Industry Canada (IC) Notices
This device complies with Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Canada, Avis d'Industrie Canada (IC)
Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s). Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under portable exposure conditions.
Information concernant l'exposition aux fréquences radio (RF)
La puissance de sortie émise par l'appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l'appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition à des appareils portables.