Hardware Set Up Instruction Manual
Smart RGB 90 LEDs Music Activated Strip Light 10ft with Remote
PRODUCT INFORMATION
Product Name: Smart LED strip light
Description: Smart RGB 90 LEDs music activated strip light, 10ft with remote.
Driver Input: 100-240V 50/60Hz, 0.2A
Driver Output: 5V 2A
Power (LED Driver): 10W
PACKAGE CONTENTS
| Part | Description | Quantity |
|---|---|---|
| 1 | Adaptor | 1 |
| 2 | 10ft LED strip | 1 |
| 3 | Smart DC controller | 1 |
| 4 | USB cable | 1 |
| 5 | Remote with 1X CR2025 battery | 1 |
| 6 | Mounting clip | 4 |
| 7 | Mounting screw | 8 |
INSTALLATION INSTRUCTION
Connect the strip light as shown in the diagrams below. Use the remote control and APP to adjust strip light functions.
Step 1: Connect Adaptor to Power Outlet
Connect the power adaptor to a wall outlet or computer/TV USB port.
[Diagram Description: A power adaptor is shown plugging into a wall socket. An arrow indicates connection to a USB cable, which then connects to a device labeled "Car adaptor/Computer/TV".]
Step 2: Connect USB Cable to Smart DC Controller
Connect the USB cable from the power source to the Smart DC controller.
[Diagram Description: A USB cable is shown connecting to the input port of a small rectangular device labeled "Smart DC Controller".]
Step 3: Connect 4-Pronged Plug to Smart DC Controller
Connect the 4-pronged plug of the LED strip to the Smart DC controller.
[Diagram Description: A 4-pronged connector from an LED strip is shown plugging into the output port of the "Smart DC Controller".]
⚠️ Important Note: If lights do not power on, flip the light strip plug around.
Step 4: Cut and Mount the LED Strip
Cut the strip light only at the marked areas if needed. Use the provided mounting clips and screws to secure the strip.
[Diagram Description: A diagram shows the LED strip with marked cut points. Two separate diagrams illustrate how to use mounting clips and screws to attach the LED strip to a surface.]
IMPORTANT NOTES
PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO USE. PLEASE NOTE THAT THE LED STRIP CAN BE PLACED OUTDOORS BUT THE POWER PACK MUST BE PLUGGED INDOORS.
NON-REPLACEABLE LED: THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN THE LIGHT SOURCE REACHES ITS END OF LIFE, THE WHOLE LUMINAIRE SHALL BE REPLACED.
FCC Compliance Information
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular situation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Re-orient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Made in China
Printed in China
This is not a toy, for decorative use only.
Distributed by: Charm Christmas Trees US LLC, 1155 Phoenixville pike suite 105 West Chester PA 19380, 1-833-386-0080
REMOTE CONTROL FUNCTIONS
[Diagram Description: Diagram of a remote control with numbered indicators pointing to various buttons for color selection, brightness adjustment, power, and effect modes.]
- To increase LED brightness
- To decrease LED Brightness
- To turn strip lights OFF
- To turn strip lights ON
- For selecting red color (Button labeled 'R')
- For selecting green color (Button labeled 'G')
- For selecting blue color (Button labeled 'B')
- For selecting white color (Button labeled 'W')
- For selecting pre-set colors (Buttons labeled with various color patterns)
- For FLASH/STROBE/FADE/SMOOTH modes (Buttons labeled 'FLASH', 'STROBE', 'FADE', 'SMOOTH')
Note: The remote also has buttons for color mixing (RGB) and brightness adjustment.
BATTERY USE AND DISPOSAL
- For best results, use a CR2025 Lithium Battery.
- Install only new batteries in your product.
- Failure to insert batteries with the correct polarity, as indicated in the battery compartment, may shorten the life of the batteries or cause the battery to leak.
- Do not dispose of batteries in fire.
- The CR2025 button battery and its tube are considered hazardous waste and should be disposed of properly at your local hazardous waste collection site for proper handling. Be sure the item holds no charge when disposing. Depending on your waste service provider, you may be able to recycle your battery. Please check with your waste service provider, as well as your local and state guidelines.
To satisfy FCC RF exposure requirements, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance are not recommended.