SOUNDPEATS Mini User Guide

First Start / Pairing

To begin using your SOUNDPEATS Mini earbuds:

1. Open the charging case lid and take out both earbuds. Remove the insulating film from the earbuds.
2. The earbuds will automatically pair with each other. The LED on the main earbud will flash red and white alternately, while the secondary earbud's LED stays white.
3. Activate Bluetooth on your device and select "SOUNDPEATS Mini" from the Bluetooth list to complete the pairing.

Reset

To reset your SOUNDPEATS Mini earbuds:

1. Clear the pairing record from your device's Bluetooth settings.
2. Place both earbuds back into the charging case and ensure they are charging.
3. Press and hold the touch buttons on both earbuds for 10 seconds until both LEDs flash red and white twice. The reset is complete.

Wearing

For a comfortable and secure fit, ensure the earbuds are inserted correctly into your ears.

[Visual Description: The manual shows an illustration of inserting the earbuds into the ear canal. It's implied to be a snug fit for optimal sound and noise isolation.]

Product Diagram

The SOUNDPEATS Mini package includes:

• Charging Case: Houses and charges the earbuds. Features an LED indicator.
• Earbuds (Left and Right): Wireless audio devices with touch controls and charging contacts.
• Charging Contacts: Located on the earbuds and inside the case for charging.
• LED Indicator: On the charging case, shows charging status and battery level.

[Visual Description: The diagram shows the charging case with earbuds inside. It highlights the earbuds, the charging contacts on the earbuds and case, and the LED indicator on the case.]

Touch Controls

MFB: Multi-Function Button (Touch Control Area)

LED Indicator Status

Charging Case LED:

• Green: 100% - 50%
• Yellow: 49% - 10%
• Red: Less than 10%
• Slow Flashing (Red/Yellow/Green): Charging the case
• Solid Green: Case fully charged

Earbud LED:

• Flashing Red and White: Pairing mode
• Solid White: Connected / Charging
• Off: Powered off / Fully charged

Q&A / Troubleshooting

Q1: What does the LED on the charging case indicate?

The LED colors indicate the battery level: Green for 100%-50%, Yellow for 49%-10%, and Red for less than 10%. When charging the case, the LED flashes slowly.

Q2: How to charge the case?

Use a Type-C adapter (current not over 1A). The LED flashes slowly while charging. It's recommended to charge the case at least once every three months if not in use for a long time.

Q3: Why are the earbuds still connected after placing them back in the case?

This can happen if the charging case battery is depleted, preventing it from turning off the earbuds. Ensure the earbuds are properly seated in the case and that the charging contacts on both the earbuds and the case are clean. Clean contacts with a soft cloth.

Q4: Why is the battery life not as advertised?

The advertised total playtime (e.g., 20 hours) includes the charging case's capacity. A single charge of the earbuds provides approximately 5 hours of playtime. The charging case provides an additional 3 recharges.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.