for Honeywell Safes & Door Locks models including: 8712409, Honeywell Safes & Door Locks,Honeywell,Honeywell,Safes,&,Door,Locks,Keyless,Entry,Door,Lock,with,Smart,Electronic,Keypad,Deadbolt,Easy,Installation,&,50,Different,Pin,Codes,Auto,Lock,Oil,Rubbed,Bronze,2.9,x,2,x,6.2,in,8712409,Oil,Rubbed,Bronze,Electronic,Entry,Deadbolt,B0BCNNN4XS,B01GGISAKQ,B01GGISAS8,B01GGISBDW,B01GGISAL0
Digital Deadbolt with Electronic Keypad – Honeywell Safes
Honeywell Safes & Door Locks - 8712309 Electronic Entry Deadbolt with Keypad, Satin Nickel, 2.9 x 2 x 6.2 inches
Honeywell Safes & Door Locks - 8712309 Electronic Entry Deadbolt with Keypad, Satin Nickel, 2.9 x 2 x 6.2 inches - Amazon.com
User Guide Digital Keypad Deadbolt ENGLISH Model 8712009 8712109 8712309 8712309L 8712409 8712509 Package Includes: 1 - Exterior Faceplate 1 - Interior Faceplate 1 - User Guide 2 - Keys 1 - Strike Plate 1 - Mounting Plate 1 - Latch 1 - 1 3/8" Screws 2 - 5/16" Screws 2 - 1 " Screws 5 - 3/4" Screws 2 - Mounting Post A B C D E F Exterior Faceplate G Interior Faceplate Mounting Plate Keys H I Latch J Strike plate K User Guide 1 3/8" Screws 1" Screws 5/16" Screws 3/4" Screws Optional Set Screw Please carefully check the above list to confirm all items have been received. If any items are missing, please contact Consumer Assistance. (See page for contact information) Read this manual carefully before installing and operating! 5 Install Interior Assembly B Carefully insert control wire into the wire connector C 1 Installation Overview NOTE: Screw Mounting Post (L) into holes on Mounting Plate (C) 6 Install Interior Assembly NOTE: Make sure the Knob is in the correct position. Be careful not to pinch the control wire when assembling B I C 2 Preparing Door NOTE: Skip this step if your door comes with pre-drilled holes. Example Refer to Template included for Door Prep Instructions F 7 Install Batteries and Cover B 3 Install Enclosed Latch and Strike Plate NOTE: Do not extend Cylindrical Cover past 2 3/4" (70mm) 2 3/8" position E 2 3/4" position TO CONVERT FROM 2 3/8" (60mm) BACKSET TO 2 3/4" (70mm) BACKSET 1. Hold latch with numbers facing forward and thumb pressing on the bolt. 2. Rotate the cylinder cover clockwise. 3. Pull and twist the extension plate all the way out. 4. Rotate the cylinder counter clockwise so that the marking aligns with the 2 3/4" position indicator. E J Strike Plate Deadbolt Latch Must Be Retracted During Installation J Do Not Over Tighten 4 Install Exterior Assembly A A Check that the Rubber Gasket is secured on the Exterior Assembly. Insert the Exterior Assembly onto the door with the tailpiece going through the Deadbolt Latch Set in the VERTICAL POSITION. Route the Control Wire through the door under the Deadbolt Latch Set. C K (optional) H Secure mounting plate to door 8 Testing Operation Test the lock button with door open Work with the door open G Test the lock NOTE: Make sure the connector dots line up with the dots on the wire Lock and unlock using the knob make sure the latch is opening and closing easily. If not, go back to step 2 and ensure you followed the steps This Electronic lock requires (4) High Quality AA Alkaline batteries. When all 4 batteries are installed in the correct position, you should hear 2 beeps and the keypad will illuminate. The Lock motor will engage and do a series of locking and unlocking motions in order to automatically determine your door "Handing" (left or right handed door). When completed the lock will beep and the keypad will flash. NOTE: Do not touch the Keypad until the light turns off. Do not use rechargeable batteries or non-alkaline batteries. Test unlocking Press 1 2 3 4 Before Opening Door Let Motor Complete Cycle Congratulations, You have Installed the Honeywell Keypad Electronic Deadbolt (8712009, 8712109, 8712309, 8712309L, 8712409, 8712509) Turn Sheet over for Programing Instructions. M8712009 8712109 8712309 8712309L 8712409 8712509 TF E V2 Programming Instructions 1 Creating Administrator Code Input Admin code (default 123456) Press 2 Adding a User Code Input Admin code (default 123456) Press Press 1 3 Unlocking Door with User Code Enter User Code Press 4 Deleting a User Code Input Admin code (default 123456) Press Press 4 Press Input 6 digit code Press Press Input user number between 02 50 Press Input new 4 8 digit user code Press Repeat the 6 digit code Press Green light flashes confirming success Repeat 4 8 digit user code Press Green light flashes confirming success Complete all the programming steps in the programming mode within 5 seconds Do not press keypad until keypad stops illuminating 5 Deleting All User Codes Input Admin code (default 123456) Press Press 3 Press Reenter Admin code Press Green light flashes confirming success 6 Additional Programming Functions Programming Symbols Lock / Clear Unlock / Programming AC Administrator Code Automatic Lock Function SET OR CANCEL AUTO LOCK You can set the lock to automatically close after each time the lock is opened. Time value range = 20 - 900 seconds, enter the following: Set Auto Lock: AC 5 Time Value Hear 1 beep and Light Indicator illuminates green. To cancel Auto Lock set the time to 00, enter the following: Cancel Time Value Auto Lock: AACC 5 00 Hear 1 beep and Light Indicator illuminates green. TEMPORARILY DISABLE: While in Auto-Lock mode, unlock door using AC , within 10 seconds you must turn the locking knob by hand to the locked position, wait more than 2 seconds then turn the locking knob back to the unlock position. The Auto-Lock mode is now disabled. RESTORE: To restore the Auto-Lock function, turn the locking knob by hand to the locked position, wait more than 2 seconds or press the Lock button on the keypad. Vacation Mode With Vacation Mode enabled, the system enters into low-power consumption mode. During this mode, all buttons and functions will be disabled until they are re-enabled. ENABLE: AC 10 1 Once the door is locked then vacation mode will be engaged and all buttons and functions will be disabled DISABLE: To disable the Vacation Mode, you must press and hold for more than 3 seconds, then input AC followed by to unlock the door. Vacation Mode is now disabled. NOTE: If you only press the for more than 3 seconds but do not input AC , the system will remain in Vacation Mode. Secure Lock-out period Warning sounds and LED flashes red after 4 incorrect code attempts: Keypad shuts down for 60 seconds. 7 Additional Programming Functions SOUND ON AND OFF You can "mute" or turn the "sound on" on your lock by entering the following. (Factory setting is sound on). AC 6 1 or 2 1 = Sound Off 2 = Sound On Sound Off (1) - Light Indicator illuminates green. Sound On (2) - Hear 1 beep and Light Indicator illuminates green. Restore Factory Settings To reset the lock to the original factory settings including the Programming Code and all User Codes follow these steps: 1. Remove one battery for 10 seconds. 2. Reinsert the battery and wait for a long and short beep 3. Press 3 times within 3 seconds. 4. The lock will beep and the light indicator will turn green. Low Battery Warning Beeps and LED flashes red 7 times. Replace with good quality alkaline batteries. Note: Removing batteries does not erase active Administrator or User Codes. Consumer Friendly Message Guide Unlock / Valid programming: Lock: Invalid Programming: Low Voltage: Super Low Voltage: 4 Incorrect code entry attempts: Power on: Chip Reset: Lock Error: Repeat operation after Lock Error: 1 long beep and LED illuminates green 2 short beeps and LED illuminates red 2 short beeps and LED flashes red twice Short beeps and LED flashes red seven times 4 short beeps and LED flashes red four times 2 short beeps and LED illuminates red each attempt 1 long beep and 1 short beep and LED illuminates green 1 long beep and 1 short beep and LED illuminates green (may occur several times or once in a while) 3 long beeps LED flashes red three times 2 short beeps three times LED flashes red six times PROGRAMMING RECORD My Codes: Programming Code User Code 02 User Code 03 User Code 04 User Code 05 User Code 06 User Code 07 User Code 09 User Code 10 User Code 11 User Code 12 User Code 13 User Code 14 User Code 15 User Code 16 User Code 17 User Code 18 Date Created (6 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / (4-8 digits) / / Press 2 Press Input existing user # between 02 50 Press Repeat the User # Press Green light flashes confirming success Troubleshooting Issue Interior Knob will not turn Lock will not function electronically Lock gives error signal when opening or locking and Deadbolt Latch will not extend or retract completely when door is closed Deadbolt Latch is sticking Keypad not working Keypad beeps and LED flashes Solution Knob or vertical tailpiece is installed in incorrect position. · Remove Interior Assembly and reposition the Interior Knob. With the Deadbolt Latch retracted verify that the tailpiece is vertical. · Check that all batteries are fresh high quality Alkaline Batteries. · Check for proper polarity (+ -) of all batteries. · Check that the Control Wire is attached to the Interior Assembly and not damaged. · Check each wire for loose or disconnected wires. · Disconnect the wiring harness and reconnect the wiring harness. · Unlock door using Key or Interior Knob. While door is open, check that the Deadbolt Latch operates smoothly. · Check for proper alignment of the strike plate, adjust as needed to assure there is no binding against the Deadbolt Latch. · Make sure tail piece is in the vertical position and straight up and down. Installation screws of the lock may be too tight and have to be loosened. · Remove Interior Assembly. · Slightly loosen the Mounting Plate screws. · Lock and unlock using the Key. · Reattach Control Wire and Interior Assembly. · Wait 60 seconds, keypad may be locked out due to incorrect code. · Replace with 4 high quality alkaline batteries. · Replace with 4 high quality alkaline batteries. CONSUMER ASSISTANCE EMAIL: LHLPCustomerService@LHLPinc.com WEBSITE: www.honeywellsafes.com ADDRESS: Consumer Assistance Dept. LH Licensed Products, Inc., 860 East Sandhill Avenue Carson, CA 90746 USA TELEPHONE: US/Canada 1-800-860-1677 Ext. 1801 (Toll Free) Mexico 01-800-288-2872 After English voice recording stops you must then enter 800-860-1677 to complete your call. (Toll Free) Australia 0011-800-5325-7000 (Toll Free) Germany/New Zealand 00-800-5325-7000 (Toll Free) Other Countries XX*-310-323-5722 (Toll Charges Apply) XX*- Dial U.S. Country Code first CALL CENTER HOURS: US/Canada 8am 5pm (Pacific**) Mon Fri (Subject to change) CALL BACK HOURS: Other Countries 8am 5pm (Pacific**) Mon Fri (Subject to change) Pacific**- Local time in Los Angeles, CA, USA * Insert correct Country Code ** Local Time based on Los Angeles California USA INTERNATIONAL CALL BACK HOURS: If you need to speak with a consumer assistant and cannot contact us during the Call Center hours above, please send an email or leave a telephone message, including your Name, Telephone Number and the best time for us to contact you during the Call Back hours above and we will make our every effort to contact you and help answer any of your questions or concerns. Limited Lifetime Mechanical and Finish Warranty / 1 Year Limited Electronics Warranty This product comes with a limited lifetime mechanical and finish warranty and a one year limited electronics warranty to the original residential consumer against defects in material and workmanship under normal use as long as the original residential purchaser occupies the residential premises upon which the product was originally installed. ORIGINAL RESIDENTIAL CONSUMER This warranty is not transferable, and applies to the original purchaser only, as long as the original purchaser occupies the residential premises upon which the product(s) was originally installed. Proof of purchase (original sales receipt) and ownership must accompany all warranty claims. All non-homeowner purchasers (including purchasers for industrial, commercial and business use) are not covered under the terms of this warranty. WHAT IS NOT COVERED This warranty is null and void if the product was used for purposes for which it was not designed. This warranty DOES NOT COVER normal wear and tear of parts or damage resulting from any of the following: negligent use, misuse or abuse of the product, or use contrary to or in violation of written instructions provided by LH Licensed Products, Inc. Further, this warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes. This warranty DOES NOT COVER scratches, abrasions, deterioration due to the use of paints, solvents or use of cleaners containing abrasives, alcohol or other solvents, whether performed by a contractor, service company, or yourself. This warranty DOES NOT COVER product(s) used in commercial applications, used in common area applications, disassembly, repair or alteration by anyone other than LH Licensed Products, Inc., improper installation or exposure to extremes of heat or humidity. This warranty DOES NOT COVER any losses, injuries to persons or loss of property, general damages or costs, and shipping and freight expenses required to return product(s) to LH Licensed Products, Inc. LH Licensed Products, Inc. shall not be liable for any indirect, incidental or consequential damages of any nature relating to this lock. LH Licensed Products, Inc. is also not responsible for costs associated with removing or reinstalling the product. ADDITIONAL TERMS LH Licensed Products, Inc. does not authorize any person to create for it any obligation or liability in connection with the Product. LH Licensed Products, Inc.'s maximum liability here under is limited to the original purchase price of the Product. No action arising out of any claimed breach of this warranty by LH Licensed Products, Inc. may be brought by the original residential purchaser more than one (1) year after the cause of action has arisen. AUSTRALIAN CONSUMER LAW Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Manufactured by: LH Licensed Products, Inc. 860 East Sandhill Avenue Carson, CA 90746 The Honeywell Trademark is used under license from Honeywell International Inc. Honeywell International Inc. makes no representations or warranties with respect to this product. www.honeywellsafes.com M8712009 8712109 8712309 8712309L 8712409 8712509 TF E V2Adobe PDF library 15.00 Adobe Illustrator 24.1 (Macintosh)