User Manual for xiaomi models including: KW66 Smart Watch, KW66, Smart Watch, Watch
East Apex (Guangzhou) Co., Ltd M66 Smart Watch 2BH7H-M66 2BH7HM66 m66
User Manual EN CN Appearances Strap Touchscreen Sensors Charging Port Power / function Button Offerings Manual Battery Charger *The schematic is a wireframe diagram for illustrative purposes only and is based on the actual object. Wear ·For everyday use, wear the watch about one finger's length from the wrist and adjust the strap to the proper tension. ·It is recommended that the strap be adjusted tightly while exercising and then adjusted to its daily looseness after exercise. *Too much slack can affect the sensor's ability to detect body parameters. Removing & Installing the Strap Attach the strap as shown. *Once assembled, pull gently to check if the assembly is successful. Download & Matching ApexWear mobile app is a necessary application to use the watch, you can download and bind the app to get a richer function experience. The specific operation steps are as follows: Power On Press and hold the button on the side of the watch for 3S to switch it on,and turn on your phone's Bluetooth. Download Mobile App Option 1:Scan the QR code at the bottom of this page in the manual to download. Option 2:Search for `ApexWear' on your mobile app shop to download. Device Binding Option 1:Bound by QR code-After the mobile phone just user registration or device page in the `add device' click on the upper right corner to enter the scanning interface, scan the watch on the QR code to bind. Option 2:Enter the device page and click `Add Device' to enter the Bluetooth name scanning mode to find the corresponding Bluetooth name and corresponding MAC address, click Connect to pair. Operating Instructions Home Page Swipe down: Pull down the convenient settings menu Swipe right: Switch between functions Swipe left: Switch between functions Swipe up: Switch between functions Other Pages Swipe right: Return to previous level Long press: Switch on/off Short press: Back to previous level Scan code to download APP Charging Instructions Aftermarket Service Place the watch on the charging connector and fully fit the charger metal contacts to the watch charging metal patch. Please use a standard USB charging cable purchased through regular channels, a charger with an output voltage of 5V and an output current of 2A or less. If the watch has been left on for too long and cannot be switched on, please connect the charger for one minute and the switch-on icon will be displayed for regular charging. When charging, please wipe the metal contacts of the charging cable and the metal contacts on the back of the watch to avoid abnormal charging due to stains and moisture. Within 12 months from the date of purchase and acceptance of this product, if product quality problems occur and are confirmed to be caused by the product itself after appraisal by the East Apex after-sales service centre, you can enjoy the repair service. The following are not covered by the warranty 1Failure or destruction of the product due to environmental factors such as natural disasters, earthquakes, lightning strikes, and abnormal voltages. 2Disassembly, modification or replacement of non-original parts by yourself or by commissioning non-original authorised manufacturers. 3Damage caused by operation not in accordance with the instruction manual or improper human operation, such as: immersion in water, corrosion, dropping, extrusion, exposure to abnormal temperature and humidity environment. DOT SINGAPORE INFINITY Customer service number WhatsApp+65 88258328 RF exposure statement This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Adobe Illustrator 26.5 (Windows) Adobe PDF library 16.07