User Manual for onsemi models including: 8310 Hardware Evaluation Board, 8310, Hardware Evaluation Board, Evaluation Board, Board
File Info : application/pdf, 12 Pages, 672.22KB
DocumentDocumentEzairo) 8310 Hardware Evaluation Board User's Manual EVBUM2877/D EVAL BOARD USER'S MANUAL www.onsemi.com INTRODUCTION Purpose IMPORTANT: onsemi acknowledges that this document might contain the inappropriate terms "white list", "master" and "slave". We have a plan to work with other companies to identify an industry wide solution that can eradicate non-inclusive terminology but maintains the technical relationship of the original wording. Once new terminologies are agreed upon, future products will contain new terminology. This group of topics provides information on the configuration and use of the Ezairo 8310 Hardware Demo Board. The Hardware Demo Board (referred to as the HDB) is designed to be used by engineers and developers along with a software development kit, such as the Ezairo 8300 SDK, to evaluate the performance and capabilities of the Ezairo 8310, and to develop applications for this device. Conventions The following conventions are used in this group of topics to signify particular types of information: Monospace font Macros, functions, defines and addresses. CAPITALIZED MONOSPACE FONT Component names and pin names. Italics File and path names, or any portion of them. <angle brackets> Optional parameters and placeholders for specific information. To use an optional parameter or replace a placeholder, specify the information within the brackets; do not include the brackets themselves. Note, Important, Caution, Warning Information requiring special notice is presented in several attention-grabbing formats depending on the consequences of ignoring the information: NOTE: Significant supplemental information, hints, or tips. IMPORTANT: Information that is more significant than a Note; intended to help you avoid frustration. CAUTION: Information that can prevent you from damaging equipment or software. WARNING: Information that can prevent harm to humans. Further Reading For any technical information not covered in this group of topics, refer to the following documents: · Integrated Development Environment User's Guide for Ezairo 8300 · CFX DSP Architecture Manual · Ezairo 8300 Hardware Reference · Ezairo 8300 Firmware Reference · Ezairo 8310 Datasheet HDB DESIGN AND OVERVIEW This topic covers an introduction to the Ezairo 8310 Hardware Demo Board, and an overview of its design and features. Introduction The Ezairo 8310 is the next generation audio DSP hybrid from onsemi, and is the successor to the Ezairo 7110. The Ezairo 8310 HDB is designed for ease of use when evaluating capabilities of, and developing applications for, the Ezairo 8310 audio DSP. For more information about the Ezairo 8310, consult the Ezairo 8310 datasheet. When using the HDB, many configuration options are available via standard 0.1-inch header pins. These pins also provide access to many of the Ezairo 8310 device's pins, including all 15 DIOs. The HDB is designed to work with the Ezairo 8300 SDK software tools created by onsemi. The Renesas® microcontroller unit (MCU) that is present on the HDB is used to interface with the Ezairo 8310, via USB with a PC, for easy debugging, data collection, and monitoring. It is also possible to perform the same operations via the 20-pin J-Link header and a J-Link communication device, or via the 6-pin DIN connector using a compatible I2C serial communication device, such as the Promira Serial Interface device. The Ezairo 8310 HDB's main functional blocks are presented in the "Ezairo 8310 HDB Overview" figure (Figure 1), below. © Semiconductor Components Industries, LLC, 2023 1 December, 2023 - Rev. 0 Publication Order Number: EVBUM2877/D EVBUM2877/D Figure 1. Ezairo 8310 HDB Overview Ezairo 8310 HDB Features The Ezairo 8310 HDB enables developers to evaluate the performance and capabilities of the Ezairo 8310, in addition to developing, demonstrating, and debugging applications. Key features of the HDB include: · Access to all debug interfaces Connectors to connect to external I2C or SWJ-DP debug communications hardware A J-link onboard solution that is accessible via the USB-C port · Access to all Ezairo 8310 interfaces via standard 0.1-inch headers · Three push-button switches 1 dedicated to resetting the device via the NRESET pin 1 connected to DIO8 1 connected to DIO9 · Test points and GND hooks for easy probing · Battery holder · Current measuring headers · Easily-configurable power supply options CONFIGURATION This group of topics describes how to configure various characteristics of your HDB for use in different circumstances. Power Supply The Ezairo 8310 HDB is equipped with a flexible and easy-to-use power supply. The HDB can be powered from any communication device that is connected to it, and can also be powered externally or via an on-board regulator. Configuration of the power supply is achieved with the following configuration headers, shown in the "Power Supply Configuration Headers" table (Table 1). www.onsemi.com 2 EVBUM2877/D Table 1. POWER SUPPLY CONFIGURATION HEADERS Designator Function PSU-SEL Main configuration header, selects the source for VBAT VBAT-I Current measurement header for VBAT REG-IN Selects the 5V source used for the HDB OD-SEL Selects the receiver output voltage source COMM-GND Connects the serial communication device's ground to the HDB ground. Keep shorted in normal operation with a serial communication device. EXT-PSU Used for connecting an external power supply. For example, it can be used to connect a bench-top power supply. VDDO2/3 Selects the power supply for the corresponding DIO domain HDB Power Supply The Ezairo 8310 can be powered from any one of several sources: the onboard battery connector, an external power supply connected via header pins, or a connected communication device. Shorting two pins together on the PSU_ SEL header chooses which supply source to use; see the "Ezairo 8310 Power Supply Options" table (Table 2) for the options available. Do not connect two different power sources at the same time. It is also possible to separately turn off the Ezairo 8310 using the on-off switch. This only turns off power to Ezairo 8310, not the onboard Renesas MCU. This can, for example, be used to save battery power when using a battery as the power supply source, because the Atmel MCU is not powered via VBAT. For the Ezairo 8310 to be powered, the VBAT-I header also needs to be shorted. The VBAT-I header optionally provides a location to measure the current consumption of the Ezairo 8310 device. When configuring the HDB to use the 1.25 V regulator, you can choose which source to power the regulator with the REG-IN header allows the user to power the board either from the 5 V supplied by the USB-C connector or from the J-Link connector. See the "VBAT Supply" table (Table 3) and the "5 V Source Selection" table (Table 4) for more details. The 1.25 V regulator is adjustable through R7 potentiometer. Table 2. Ezairo 8310 POWER SUPPLY OPTIONS PSU_SEL Power Supply Source Short pin 1 to 2, all others open CS44 optional connector Short pin 3 to 4, all others open 1.25 V on-board LDO Short pin 5 to 6, all others open Promira Communication Device Short pin 7 to 8, all others open External Bench Power Supply Short pin 9 to 10, all others open Battery (onboard battery holder) Table 3. VBAT SUPPLY Pin Name Min Nom Max VBAT* 0.9 V 1.25 V 2.0 V *VBAT below 1.0 V leads to degraded performance of the internally regulated power rails. Table 4. 5 V SOURCE SELECTION REG-IN 5 V Source Short pin 1 to 2 The selected source is USB-C Short pin 2 to 3 The selected source is the J-Link connector DIO Power Supply The Ezairo 8310 exposes 15 DIOs split among 3 different power domains: VBAT, VDDO2 and VDDO3. On the Ezairo 8310 HDB VDDO2 and VDDO3 domains are connected to selection headers that allows the domains to be powered by VBAT or VDDIF. The "VDDOx Power Supply Options and Configuration" table (Table 5) details the configuration options. Table 5. VDDOx POWER SUPPLY OPTIONS AND CONFIGURATION VDDOx Source Header Configuration VDDIF Short pins 1 & 2 VBAT Short pins 3 & 4 Renesas Microcontroller Power Supply The Renesas MCU core is powered by a 3.3 V LDO regulator, which is in turn powered by a 5 V rail supplied by a USB connection. The rest of the voltage supplied to the MCU, for digital inputs/outputs, analog references, etc., are provided by the 3.3 V regulator. www.onsemi.com 3 EVBUM2877/D Communication There are three ways of achieving communication between the Ezairo 8310 Hardware Demo Board and the Ezairo 8300 Evaluation and Development Board. The USB-C connection (J10) is a J-Link onboard solution that provides a SWJ-DP interface for debugging the Ezairo 8310 at up to 2MHz. The TC2030-IDC connector (J11 header) is used to program the Arm® Cortex®-M3 processor with J-Link firmware. This is pre-programmed onto the HBD as a factory standard. It is also possible to connect and debug the Ezairo 8310 via standard JTAG. The JTAG (JLINK header) connector is compatible with SEGGER® J-Link debugging devices. Additionally, communication and debugging of Ezairo 8310 can be achieved through the Promira Serial Platform from Total Phaset, through an I2C interface. The Communication Accelerator Adapter (CAA) is also supported but is considered obsolete. The serial interface can be connected to the CAA or Promira through the 6-pin DIN connector. The "DIN Connector Pinout" table (Table 6) shows details of the DIN connector. Table 6. DIN CONNECTOR PINOUT Pin Number Serial Interface Pin Description 1 Supply Voltage from the Serial Interface 2 System Ground 3 SCL (I2C Clock) 4 SDA (I2C data) 5 VBAT (Sense Voltage) 6 No Connect For troubleshooting purposes, the I2C signals can be probed on a standard 0.1-inch header, labelled IC, that allows connection to the SDA (pin 2) and SCL (pin 1). A block diagram of the communication connections is shown in the "Hardware Demo Board Communication Connections" figure (Figure 2), and an overview in tabular form is presented in the "Communication Configuration" table (Table 7). Figure 2. Hardware Demo Board Communication Connections Table 7. COMMUNICATION CONFIGURATION Designator Configuration Description SENSE COMM-GND Connects VBAT to the SENSE pin on the 6-pin DIN connector, if shorted Connects the ground from the Promira /CAA to the HBD ground, if shorted EXT-CLK I2C Pin used to connect an external clock source to drive the Ezairo 8310 Can be used to connect an I2C device, instead of using the 6-pin DIN connector www.onsemi.com 4 EVBUM2877/D Input Stage A new feature of Ezairo 8300, and therefore of Ezairo 8310, is a very high impedance input stage (~GW). This necessitates some consideration when connecting devices to the inputs. The most important factor is the need to add a DC bias for devices that do not inherently produce a DC bias of their own. Since microphones produce their own DC bias, they do not cause an issue. However, many audio measurement instruments do not introduce DC bias, and for these, the bias needs to be added. To connect a device that does not generate a DC bias, see the "Header Configuration Required to Enable DC Bias" table (Table 8). To connect a device that generates its own DC bias, such as a microphone, see the "Header Configuration for Disabling DC Bias" table (Table 9). Table 8. HEADER CONFIGURATION REQUIRED TO ENABLE DC BIAS Designator Configuration for DC Bias VDC-BIAS Short pins 2 & 3 BIAS Short pins 1 & 2 for channel AI0 Short pins 3 & 4 for channel AI1 Short pins 5 & 6 for channel AI2 Short pins 7 & 8 for channel AI3 C-BYPx Leave open pins 1 & 2 AIx/MICx Connect audio source to Aix or MICx, leave other connector open FILTEN1, RCVR0, and RCVR1. Separate RC filter networks are provided to attenuate out-of-band noise from the direct digital outputs when connected to high impedance audio measurement equipment (OD0, OD1). The onboard RC filters are enabled by the FILTEN0/FILTEN1 headers as described in the "Output Stage Enable Configuration" table (Table 10). The user can choose to use VBAT as the output driver supply voltage, or supply a separate voltage on the VBATOD header. To enable these options, follow the "Onboard RC Filter Configuration" table (Table 11). Table 10. OUTPUT STAGE ENABLE CONFIGURATION Designator Configuration Description OD-SEL Short pins 1 & 2 to power the output drivers with VBAT. Leave pins 1 & 2 open and connect a voltage source to the VBATOD header to power the output drivers from an external source. Table 11. ONBOARD RC FILTER CONFIGURATION Function FILTEN0/FILTEN1 Disabled Open pins 1 to 3 Open pins 2 to 4 Enabled Short pins 1 to 3 Short pins 2 to 4 Table 9. HEADER CONFIGURATION FOR DISABLING DC BIAS Designator Configuration for DC Bias VDC-BIAS Leave open BIASx Leave open C-BYPx Leave open AIx/MICx Leave open AIxH Connect audio source Output Stage There are two digital outputs (RCVR0, RCVR1) available on the HDB through standard 0.1-inch header. The direct digital outputs are available on headers FILTEN0, NOTE: To connect receivers or loudspeakers (without the RC filter), use headers RCVR0/RCVR1 or FILTEN0/FILTEN1. Digital Input/Output (DIO) The Ezairo 8310 HDB contains 15 DIO signals available on three headers DIO1, DIO2 and DIO3. The headers provide access to all DIO signals, which in turn provide access to a wide variety of interfaces (GPIO, SPI, PCM, I2C, UART, LSAD, clocks). See the "DIO/RFIO Reference Domains" table (Table 12) for pinout and reference domains. The three available sources for the VDDO domains (VDDIF, VDDO2 and VDDO3) are available at each end of the row of DIO headers. Table 12. DIO/RFIO REFERENCE DOMAINS DIOs DIO Header Pin Header Reference Domain Alternate Function on Board 5 3 DIO1 VDDIF SPI_CS (externalmemory) 8 5 DIO1 VDDIF DIO8-SW 9 7 DIO1 VDDIF DIO9-SW 10 2 DIO1 VDDIF 11 4 DIO1 VDDIF 18 3 DIO2 VDDO2 19 5 DIO2 VDDO2 www.onsemi.com 5 EVBUM2877/D Table 12. DIO/RFIO REFERENCE DOMAINS (continued) DIOs DIO Header Pin Header Reference Domain 20 7 DIO2 VDDO2 21 2 DIO2 VDDO2 22 4 DIO2 VDDO2 23 6 DIO2 VDDO2 24 3 DIO3 VDDO3 25 5 DIO3 VDDO3 26 7 DIO3 VDDO3 28 2 DIO3 VDDO3 Alternate Function on Board The Ezairo 8310 HDB has two momentary switches that can be used as momentary hard pull-downs on DIO8 and DIO9 (SW3). DIO35 is also connected to the EXT-CLK header for connecting an external clock source to the Ezairo 8310. The RESET switch can be used to reset the Ezairo 8310. For more information on the DIOs, refer to the Ezairo 8300 Hardware Reference. Test Point Headers The "Measurement Test Points" table (Table 13) shows a list of 0.1-inch headers on the HDB that are provided as measurement test points. There are also several ground hooks available on the HDB as an easy way to provide a reference. These hooks provide easy access to DGND, GND-BAT, AGND and GNDOD. Table 13. MEASUREMENT TEST POINTS Designator Measurement VREG Output of the band-gap reference regulator in the Ezairo 8300 VBAT Output voltage of the connected battery/chosen voltage source VDDIF Output of the interface charge pump VDDO2, VDDO3 Voltage reference of the DIO2,3 domains VBATOD Voltage for the audio output driver 1V25 Output of 1.25V LDO SPI Enables probing of the SPI lines while communicating with non-volatile memories VMIC Output of the microphone voltage regulator VBAT-I Current measurement pin. Place a DMM across these two pins in current mode to measure the current consumption of the whole Ezairo 8310 device. Keep shorted otherwise. Can be used as an enable pin. Indicator LEDs The on-board J-Link debugger has a green LED indicator connected on P111 of the Renesas MCU. www.onsemi.com 6 EVBUM2877/D APPENDIX A HEADERS, CONNECTORS AND SCHEMATICS This topic contains useful tables describing the headers on the Ezairo 8310 HDB, the connectors present on the Ezairo 8300 EVB, and schematic drawings of the Ezairo 8310 HDB for your reference. Headers on the Ezairo 8310 HDB This section contains a list and description of all headers present on the HDB, shown in the "List of Headers on the Ezairo 8310 HDB" table (Table 14). Table 14. LIST OF HEADERS ON THE EZAIRO 8310 HDB Designator Description SENSE Used for connecting the sense voltage to the Promira COMM-GND Used for connecting the Promira ground to the HDB ground EXT-PSU Used for connecting an external power supply PSU-SEL I2C VBAT-I Used to select power source for VBAT, to power Ezairo 8310 Used for connecting an I2C device to communicate with Ezairo 8310 Current measurement header. Keep shorted in normal operation. VDC-BIAS Connects VREG to the analog audio inputs to provide DC bias. BIAS0/1/2/3 need to be connected as well. BIAS Part of the DC biasing circuit used for the analog audio inputs. Short the header that corresponds to the input being biased. C-BYP0/1/2/3 Used to bypass the DC blocking capacitor on the analog inputs from the RCA jacks/MICx headers MIC0/1/2/3 Used to connect a 3 pin microphone input, typically a microphone RESET Can be shorted to reset the Ezairo 8300 module MIC-GND Determines the ground reference used by the audio inputs. Connect pins 2 & 3 to use GMIC; recommended when using a microphone. Connect pins 1 & 2 to use AGND; recommended for use with audio measurement instruments. EXT-CLK RCVR0 External clock source Direct digital audio output 0. Allows connection via 0.1 inch headers to audio measurement devices when the output filters are enabled. RCRV1 Direct digital audio output 1. Allows connection via 0.1 inch headers to audio measurement devices when the output filters are enabled. FILTEN0 FILTEN1 OD0 Enables the analog output filter for analog output 0 Enables the analog output filter for analog output 1 Used to connect to the filtered analog output 0 OD1 Used to connect to the filtered analog output 1 VREG VMIC Measurement header for VREG internal regulator Measurement header for VMIC internal regulator VBATOD Used for connecting an external power source to power the output drivers VDDIF Measurement header for VDDIF internal regulator/charge pump VBAT 1V25 Measurement header for VBAT internal regulator Measurement header for 1V25 voltage rail REG-IN Header for selecting the 5 V source for the 1.25V switching regulator. Short pins 2 & 3 to select J-Link 5V as the source, and short pins 1 & 2 to select USB 5V as the source. SPI Allows probing of the SPI signals VDDO2,3 Measurement header for VDDOx internal regulator VDD02/3-S Used for selecting source for VDDO reference for each VDDO domain. Short pins 1 & 2 to select VDDIF as the source. Short pins 3 & 4 to select VBAT as the source. DIO1/2/3 Each of these headers contains all of the DIO pins associated with the corresponding VDDOx domain. DEBUG-EN Enables debug of the Ezairo 8300 via the Renesas MCU and USB-C connection www.onsemi.com 7 EVBUM2877/D Ezairo 8300 EVB Connectors The "List of Connectors on the Ezairo 8300 EVB" table (Table 15) lists all connectors present on the EVB, and the purpose of each. Table 15. LIST OF CONNECTORS ON THE EZAIRO 8300 EVB Connector J2 Description 6-pin mini-DIN connector used for communicating with serial I2C devices, such as the Promira J1 OD0 16mm battery holder RCVR0 audio output via header OD1 RCVR1 audio output via header J10 USB-C connector used to communicate with the Ezairo 8310 via onboard J-link J11 TC2030-IDC connector for programming firmware into the Atmel MCU. Intended for manufacturing use. RCVR0 Header for unfiltered RCVR0 output RCVR1 Header for unfiltered RCVR1 output MIC0/1/2/3 Analog input headers, corresponding to the appropriate input on the Ezairo 8310 JLINK 20-pin header used to connect the J-Link debugging device www.onsemi.com 8 EVBUM2877/D Schematics This section contains the schematic diagrams for the Ezairo 8310 HDB, shown in the "Power Supply and Communications Schematics" figure (Figure 3), the "DUT Schematics" figure (Figure 4), and the "Debug Interface Schematics" figure (Figure 5). Figure 3. Power Supply and Communications Schematics www.onsemi.com 9 EVBUM2877/D Figure 4. DUT Schematics www.onsemi.com 10 EVBUM2877/D Figure 5. Debug Interface Schematics Ezairo and SignaKlara are either trademarks or registered trademarks of Semiconductor Components Industries, LLC dba "onsemi" or its affiliates and/or subsidiaries in the United States and/or other countries. All other brand names and product names appearing in this document are trademarks of their respective holders. www.onsemi.com 11 onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba "onsemi" or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. The evaluation board/kit (research and development board/kit) (hereinafter the "board") is not a finished product and is not available for sale to consumers. The board is only intended for research, development, demonstration and evaluation purposes and will only be used in laboratory/development areas by persons with an engineering/technical training and familiar with the risks associated with handling electrical/mechanical components, systems and subsystems. This person assumes full responsibility/liability for proper and safe handling. Any other use, resale or redistribution for any other purpose is strictly prohibited. THE BOARD IS PROVIDED BY ONSEMI TO YOU "AS IS" AND WITHOUT ANY REPRESENTATIONS OR WARRANTIES WHATSOEVER. WITHOUT LIMITING THE FOREGOING, ONSEMI (AND ITS LICENSORS/SUPPLIERS) HEREBY DISCLAIMS ANY AND ALL REPRESENTATIONS AND WARRANTIES IN RELATION TO THE BOARD, ANY MODIFICATIONS, OR THIS AGREEMENT, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING WITHOUT LIMITATION ANY AND ALL REPRESENTATIONS AND WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, NON-INFRINGEMENT, AND THOSE ARISING FROM A COURSE OF DEALING, TRADE USAGE, TRADE CUSTOM OR TRADE PRACTICE. onsemi reserves the right to make changes without further notice to any board. You are responsible for determining whether the board will be suitable for your intended use or application or will achieve your intended results. Prior to using or distributing any systems that have been evaluated, designed or tested using the board, you agree to test and validate your design to confirm the functionality for your application. Any technical, applications or design information or advice, quality characterization, reliability data or other services provided by onsemi shall not constitute any representation or warranty by onsemi, and no additional obligations or liabilities shall arise from onsemi having provided such information or services. onsemi products including the boards are not designed, intended, or authorized for use in life support systems, or any FDA Class 3 medical devices or medical devices with a similar or equivalent classification in a foreign jurisdiction, or any devices intended for implantation in the human body. You agree to indemnify, defend and hold harmless onsemi, its directors, officers, employees, representatives, agents, subsidiaries, affiliates, distributors, and assigns, against any and all liabilities, losses, costs, damages, judgments, and expenses, arising out of any claim, demand, investigation, lawsuit, regulatory action or cause of action arising out of or associated with any unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of any products and/or the board. This evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and may not meet the technical requirements of these or other related directives. FCC WARNING This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation purposes only and is not considered by onsemi to be a finished end product fit for general consumer use. It may generate, use, or radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this equipment may cause interference with radio communications, in which case the user shall be responsible, at its expense, to take whatever measures may be required to correct this interference. onsemi does not convey any license under its patent rights nor the rights of others. LIMITATIONS OF LIABILITY: onsemi shall not be liable for any special, consequential, incidental, indirect or punitive damages, including, but not limited to the costs of requalification, delay, loss of profits or goodwill, arising out of or in connection with the board, even if onsemi is advised of the possibility of such damages. In no event shall onsemi's aggregate liability from any obligation arising out of or in connection with the board, under any theory of liability, exceed the purchase price paid for the board, if any. The board is provided to you subject to the license and other terms per onsemi's standard terms and conditions of sale. For more information and documentation, please visit www.onsemi.com. ADDITIONAL INFORMATION TECHNICAL PUBLICATIONS: Technical Library: www.onsemi.com/design/resources/technical-documentation onsemi Website: www.onsemi.com ONLINE SUPPORT: www.onsemi.com/support For additional information, please contact your local Sales Representative at www.onsemi.com/support/sales www.onsemi.com 1