User Guide for DSC models including: PC1864 GT Cellular Communicator and Programming the Panel, PC1864, GT Cellular Communicator and Programming the Panel, Communicator and Programming the Panel, Programming the Panel, the Panel, Panel
DSC PC1864 for GT - Trikdis
Installation schematics - Trikdis
File Info : application/pdf, 4 Pages, 624.24KB
DocumentDocumentPC1864 Wiring Trikdis GT+ Cellular Communicator and Programming the Panel CAUTION · The communicator should be installed and maintained by qualified personnel. · Prior to installation, it is advised to read full device installation manual carefully in order to avoid mistakes that can lead to malfunction or even damage the equipment. · Disconnect the power supply before making any electrical connections. · Changes, modifications or repairs not authorized by the manufacturer shall void your rights under the warranty. Schematics for wiring the communicator to the security control panel Following the schematics provided below, wire the communicator to the control panel. T-1 R-1 TIP RING EGND Z8 COM Z7 Z6 COM Z5 Z4 COM Z3 Z2 COM Z1 4PGM3 2PGM1 GRN YEL BLK RED -BELL+ - + AUX AC DSC PC1864 trikdis.com PC1864 Wiring Trikdis GT+ Cellular Communicator and Programming the Panel DSC PC1864 panel do not need to be programmed. LED indication of communicator operation Indicator Light status NETWORK Off Yellow blinking Green solid with yellow blinking Off Green solid Green blinking Off Green solid Yellow solid Green solid and yellow blinking Yellow solid Off 1 red blink 2 red blinks 3 red blinks 4 red blinks 5 red blinks 6 red blinks 7 red blinks 8 red blinks Red blinking Red solid 1 green blink 2 green blinks 3 green blinks 4 green blinks 5 green blinks 6 green blinks No connection to cellular network Connecting to cellular network Communicator is connected to cellular network. Yellow blinks count indicates signal strength, 10 blinks max. Sufficient cellular signal strength for 4G network level 3 (three yellow flashes). No unsent events Unsent events are stored in buffer (Configuration mode) Data is being transferred to/from communicator Power supply is off or disconnected Power supply is on with sufficient voltage Power supply voltage is insufficient (11.5V) Configuration mode) Communicator is ready for configuration (Configuration mode) No connection with computer No operation problems SIM card not found SIM card PIN code problem (incorrect PIN code) Programming problem (No APN) Registration to GSM network problem Registration to GPRS/UMTS network problem No connection with the receiver Lost connection with control panel The entered ICCID number does not match the ICCID number of the SIM card (Configuration mode) Memory fault (Configuration mode) Firmware is corrupted None GSM GPRS EDGE HSDPA, HSUPA, HSPA+, WCDMA LTE TDD, LTE FDD trikdis.com PC1864 Wiring Trikdis GT+ Cellular Communicator and Programming the Panel Setting up the GT+ communicator with the app Download and launch the Protegus application or use the browser version: web.protegus.app. The installer must connect to Protegus with an installer account. Step 1 Step 2 Step 3 Step 4 Station 1 Station 2 Click the "Add new system" Enter the IMEI number of button the communicator Select security company Step 5 Step 6 Step 7 Press "DSC" Step 8 Press "PC1864" Enter "Object ID" and Wait while the "Module ID". Press "NEXT" configuration is written Press "Add to Protegus2" trikdis.com PC1864 Wiring Trikdis GT+ Cellular Communicator and Programming the Panel Setting up the GT+ communicator with the app Step 9 Step 10 Step 11 Step 12 Enter system "Name". Press "Next" Step 13 Press "Skip" Step 14 Press on system Wait 1 minute and press "Transfer" After completing the setup and installation perform a system check: 1. Create an event: - by arming/disarming the system with the control panel's keypad; - by triggering a zone alarm when the security system is armed. 2. Make sure that the event arrives to the CMS (Central Monitoring Station) and the Protegus app. Enter the e-mail of the user to whom the installer will transfer the system. Press "Transfer" The system will appear in Protegus on the user's phone trikdis.com