Manual-Hub.com - Free English product PDF Documents!
Installation Guide for Altronix models including: TANGO8P PoE Driven Multi Output Power Supply with Lithium Battery Backup, TANGO8P, PoE Driven Multi Output Power Supply with Lithium Battery Backup, Multi Output Power Supply with Lithium Battery Backup, Output Power Supply with Lithium Battery Backup, Lithium Battery Backup
ALTRONIX TANGO8P (01) PDF MANUAL - Manual-Hub.com
File Info : application/pdf, 8 Pages, 1.28MB
DocumentDocumentPoE Driven Multi-Output Power Supply with Lithium Battery Backup Installation Guide Tango8P - 12VDC and/or 24VDC selectable by output @ 75W max. - Eight (8) fuse protected outputs - Built-in Lithium Iron Phosphate Battery Charger Tango8PCB - 12VDC and/or 24VDC selectable by output @ 75W max. - Eight (8) Class 2 power-limited PTC protected outputs - Built-in Lithium Iron Phosphate Battery Charger Rev. TANGO8P-083019 https://manual-hub.com/ More than just power.TM Table of Contents: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Stand-by Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 4 LED Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 5 Terminal Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 5 Enclosure Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 8 - 2 - https://manual-hub.com/ Tango8P(CB) - PoE Driven Multi-Output Power Supply Overview: Altronix Tango8P(CB) PoE Driven Multi-Output Power Supply converts an IEEE802 .3bt PoE input into eight (8) regulated 24VDC and/or 12VDC outputs up to 75W . It eliminates the need for a high voltage inside the enclosure . Tango8P(CB) is designed to support a single 12V LiFePO4 (Lithium Iron Phosphate) battery for 12VDC and 24VDC backup . Specifications: Ethernet Input: · 802 .3bt PoE up to 90W or 802 .3at up to 30W or 802 .3af up to 15W . Power Output (when using 802.3bt 90W): · 12VDC up to 6 .25A (75W) and/or 24VDC up to 3A (75W) . Combined output not to exceed 75W . · When charging batteries: 12VDC up to 5 .4A (65W) and/or 24VDC up to 2 .7A (65W) Combined output not to exceed 65W . · Tango8P: Fuse protected outputs rated @ 3A per output, non power-limited . Tango8PCB: PTC protected outputs rated @ 2A per output, Class 2 power-limited . · Any of the eight (8) fuse/PTC protected power outputs are selectable to follow power Input 1 or Input 2 . Output voltage of each output is the same as the input voltage of the input selected . · Individual outputs may be set to OFF position for servicing . · Surge suppression . Fuse/PTC Ratings: · Main input fuses rated @ 10A/32V each . · PDS8: output fuses rated @ 3A/32V each . · PDS8CB: output PTCs rated @ 2A each . · TANGO1B: battery fuse rated @ 10A/32V each . Ethernet Output (Tango1B): · Pass-through Ethernet Port (data only) . · 100/1G . Battery (Tango1B): · 12VDC battery charger for Lithium Iron Phosphate Battery (LiFeP04 only) . Battery (cont'd) (Tango1B): · Unique technology allows for single battery to backup 12VDC and/or 24VDC systems . · Low power shutdown . Shuts down DC output terminals if battery voltage drops below 80% of nominal . Prevents deep battery discharge . Supervision: · Loss of PoE Input . · Battery Supervision . Visual Indicators: · Tango1B - Input indicates input voltage is present . - Battery status indicates battery trouble condition . - PoE Class indicator . - Supervision PoE Fail or BAT Fail . · PDS8(CB) - Individual voltage LEDs indicate 12VDC (Green) or 24VDC (Green and Red) . Environmental: · Operating temperature: 0ºC to 49ºC ambient . · Humidity: 20 to 85%, non-condensing . Enclosure Dimensions (approximate H x W x D): 15 .5" x 12 .25" x 4 .5" (394mm x 311mm x 114mm) . Accessories: Power Sourcing Equipment NetWay1BT - Single Port Managed Hi-PoE Injector supplies 90W total power . NetWaySP1BT - 802 .3bt Media Converter/ Injector supplies 90W total power . NetWay4BT - 4-Port Managed Hi-PoE Midspan Injector supplies 480W total power . NetWay8BT - 8-Port Managed Hi-PoE Midspan Injector supplies 480W total power . Battery 4AH 7AH 12AH Stand-by Specifications: Access Control Applications Stand-by 30 Mins . 45 Mins . 1 .5 Hours Tango8P(CB) - PoE Driven Multi-Output Power Supply https://manual-hub.com/ - 3 - Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, the Canadian Electrical Code and with all local codes and authorities having jurisdiction . Product is intended for indoor use only . 1 . Mount unit in desired location . Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure . Install two upper fasteners and screws in the wall with the screw heads protruding . Place the enclosure's upper keyholes over the two upper screws, level and secure . Mark the position of the lower two holes . Remove the enclosure . Drill the lower holes and install the two fasteners . Place the enclosure's upper keyholes over the two upper screws . Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 8) . Secure enclosure to earth ground . 2 . Ensure all output jumpers [OUT1 - OUT8] on PDS8(CB) are placed in the OFF (center) position marked [·] (Fig. 1, pg. 4) . Fig. 1 OFF 3 . Connect IEEE802 .3bt PSE from PoE source to RJ45 Jack marked [PoE+ Data Input] IN1 on the Tango1B board (Fig. 2b, pg. 4). If Data pass-through is required, connect another IN2 IEEE802 .3bt PSE to RJ45 Jack marked [Data Output] (Fig. 2a, pg. 4) . CAUTION: Do not touch exposed metal parts. There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel. 4 . Set each output [OUT1 - OUT8] to route power from Input 1 or Input 2 (jumper position 1 or 2) (Fig. 1, 2, pg. 4, Fig. 3 pg. 6) . IN1 = 24VDC, IN2 = 12VDC . Note: Measure output voltage before connecting devices . This helps avoiding potential damage . 6 . Connect devices to terminal pairs 1 to 8, marked [P (Positive) - OUT1-OUT8, N (Negative)] (Fig. 2, pg. 4, Fig. 3 pg. 6) . 6 . When the use of stand-by batteries is desired, they must be Lithium Iron Phosphate (LiFePO4) . Connect batteries to the terminals marked [+ BAT ] on Tango1B (battery leads included) (Fig. 2f, pg. 4) . 7 . Connect appropriate signaling notification devices to terminals marked [C FAIL NC] (Fig. 2c, pg. 4) supervisory relay output . Fig. 2 - Tango1B with PDS8 stacked above OFF IN1 IN2 IN2 Fuse + INP1 -- + INP2 -- PWR1 + IN1 Fuse PDS8 Dual Voltage 10 PDS8CB Power Distribution PWR1 + Module 2a 2f 10 3 3 3 3 3 3 3 3 Out8 <1 off 2> Out7 <1 off 2> Out6 <1 off 2> Out5 <1 off 2> Out4 <1 off 2> Out3 <1 off 2> Out2 <1 off 2> Out1 <1 off 2> 2e 1g P 2d COM (--- ) OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8 N 2b COM (--- ) 2c PWR2 + 1 2 3 4 5 6 7 8 PWR2 + Common Power Outputs (NEG) Wiring: Use 18 AWG or larger for all low voltage power connections . - 4 - https://manual-hub.com/ Tango8P(CB) - PoE Driven Multi-Output Power Supply Tango1B LED Input Battery PoE Supervision LED Diagnostics: ON Input voltage is present . Normal operating condition . Indicates Class . PoE Fail or BAT Fail . BLINKING Input voltage not present . Battery is low or missing . Refer to table below Classes 3-8 NC dry contact 30V 1A (not an LED) Class Green Red Blue Class 1 Class 2 Class 3 Off Off Off Class 4 Off On Off Class Green Red Blue Class 5 On Off On Class 6 On Off On Class 7 On On On Class 8 On On On PDS8: LED ON Green 12VDC Output . Green and Red 24VDC Output . Tango1B Terminal/RJ45 Legend PoE+ Data Input Data Output C FAIL NC + 12V + 24V + BAT 8-Pin Connector (Fig. 2g, pg. 4) PDS8: Terminal Legend + INP1 + INP2 P [OUT1-OUT8] N [OUT1-OUT8] Terminal Identification: Function/Description IEEE802 .3bt Input (Fig. 2b, pg. 4) . Passes Data to Switch (Fig. 2a, pg. 4) Power and Battery Fail (Fig. 2c, pg. 4) . 12VDC output (Fig. 2d, pg. 4) . 24VDC output (Fig. 2e, pg. 4) . Lithium Iron Phosphate battery backup (Fig. 2f, pg. 4) . Facilitates electrical connection to PDS8(CB) . Function/Description Factory connected to Tango1B . Do not use these terminals . Factory connected to Tango1B . Do not use these terminals . Positive DC power outputs . Negative DC power outputs . Tango8P(CB) - PoE Driven Multi-Output Power Supply https://manual-hub.com/ - 5 - Fig. 3 - Tango8P(CB) OFF IN1 IN2 LiFeP04 Battery connection (non power-limited) Supervision (power-limited) + INP1 -- + INP2 -- Out8 <1 off 2> PWR1 + 10 3 IN1 Fuse 10 PDS8 PDS8CB Dual Voltage Power Distribution Module PWR1 + 3 3 3 3 3 3 3 IN2 Fuse Out7 <1 off 2> Out6 <1 off 2> Out5 <1 off 2> Out4 <1 off 2> Out3 <1 off 2> Out2 <1 off 2> Out1 <1 off 2> P COM (--- ) PWR2 + OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8 N COM (--- ) 1 2 3 4 5 6 7 8 PWR2 + Common Power Outputs (NEG) DC Output to devices (Tango8P - non power-limited, Tango8PCB - power-limited) Data Pass-Through PoE Input PTC Protected Outputs on Tango8PCB Optional LiFeP04 Battery - 6 - https://manual-hub.com/ Tango8P(CB) - PoE Driven Multi-Output Power Supply Notes: Tango8P(CB) - PoE Driven Multi-Output Power Supply https://manual-hub.com/ - 7 - Enclosure Dimensions (BC400): 15 .5" x 12 .25" x 4 .5" (394mm x 311mm x 114mm) 1.5" (38.1mm) 4.615" (117.22mm) 4.615" (117.22mm) 1.25" (31.75mm) 4.5" (114.3mm) 1.5" (38.1mm) 1.1" (27.94mm) 0.91" (23.114mm) 12.23" (310.64mm) 1.5" (38.1mm) 1.75" (44.45mm) 1.375" (34.925mm) 1.125" (28.575mm) 1.1" (27.94mm) 0.91" (23.114mm) 4.5" (114.3mm) 1.25" (31.75mm) 1.5" (38.1mm) 2.0" (50.8mm) 2.0" (50.8mm) 5.0" (127.0mm) 1.25" (31.75mm) 15.5" (393.7mm) 1.1" (27.94mm) 0.79" (20.06mm) 1.5" (38.1mm) 4.615" (117.22mm) 4.615" (117.22mm) 1.75" (44.45mm) 1.5" (38.1mm) 5.0" (127.0mm) 1.25" (31.75mm) Altronix is not responsible for any typographical errors . 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www .altronix .com | e-mail: info@altronix .com | Lifetime Warranty | Made in U .S .A . IITango8P(CB) I20S - 8 - https://manual-hub.com/ MEMBER Tango8P(CB) - PoE Driven Multi-Output Power Supply