60 inch Four Layer Iron Mesh Storage Rack

Safety Information and Warnings

⚠️ WARNING!

To reduce the risk of injury, user must read instructions manual carefully.

The symbol ⚠️, placed before a safety comment, indicates a kind of precaution, warning, or danger. Ignoring this warning may lead to an accident. To reduce the risk of injury, fire, or electrocution, please always follow the recommendation shown below.

? Warning: Be sure to wear gloves when using this product.

General Warnings and Precautions

1. Keep this manual for safety warnings and precautions. It offers important information on how to assemble, use, and maintain this product.
2. Please handle metal edges carefully.
3. DO NOT stand on this product or use it as a ladder.
4. DO NOT alter this product in any manner that is not intended, as this may cause product damage or personal injury.
5. Always assemble on an even surface.
6. The maximum loaded weight for each shelf is no more than 180 kg, evenly distributed.
7. Store the heaviest items on lower shelves.
8. Attach the unit to the wall if filling to capacity (fittings not included).

Assembly Precautions

1. Please assemble the product in strict accordance with the instructions. Incorrect assembly could be hazardous.
2. Please wear goggles and work gloves correctly when assembling. Place a piece of cloth or wood between the hammer head and the part, or use a rubber mallet.
3. Do not try to assemble the product when feeling tired or when under the influence of alcohol, drugs, or medication.
4. Load bearing capacity and other product parameters are applied to the properly and completely assembled product only.

Use Precautions

1. This product is not a toy. Do not allow children to play with or get access to this item.
2. Check carefully before use. Do not use if parts get loosened or damaged.
3. Use on flat, level, and hard surfaces only.
4. Do not exceed the listed load bearing capacity. Tighten all the knobs securely before placing weights on. Be aware of the dynamic load bearing capacity! Sudden load changes may temporarily cause excessive load, resulting in product failure.

Parts List

The following parts are included:

• 1: Upright Posts (4 pieces)
• 2: Feet (4 pieces)
• 3: Wire Mesh Shelves (4 pieces)
• 4: Beams (8 pieces)
• 6: Cross Braces (8 pieces)
• 7: Connectors/Clips (quantity not specified, used for securing)

Hardware List

The following hardware is included:

• A: Nut (2 pieces)
• B: Screw (2 pieces)
• C: Washer (2 pieces)

Note: The quantities for hardware A, B, C seem to be minimal in the list, but the diagrams might imply more are used. The PDF only states 2 PCS for each.

Assembly Instructions

Step 1: Attach Feet

Take the 4 Upright Posts (1) and attach the 4 Feet (2) to the bottom of each post. The diagram shows the feet being inserted and possibly secured with a hammer or mallet.

Step 2: Assemble First Level

Attach 4 Beams (4) to the lower sections of two Upright Posts (1). Secure these beams using 8 Cross Braces (6), connecting them between the beams and to the posts. The diagram shows how the beams and braces slot into the posts. Hardware (A, B, C) might be used here, though not explicitly shown in this step's diagram.

Step 3: Add Upright Posts

Attach two more Upright Posts (1) to the assembled structure. Use 7 Connectors/Clips to secure these posts to the existing beams or structure. The diagram shows clips being inserted into holes.

Step 4: Add More Upright Posts

Continue adding the remaining Upright Posts (1) and securing them with 7 Connectors/Clips, following the pattern shown in the diagram.

Step 5: Assemble Remaining Levels

Attach the remaining 4 Beams (4) to the upright posts at the desired shelf heights. Secure these beams using the remaining 8 Cross Braces (6). The diagram illustrates the placement of beams and braces for the upper levels.

Step 6: Place Wire Mesh Shelves

Carefully place the 4 Wire Mesh Shelves (3) onto the assembled beams (4).

Step 7: Secure Wire Mesh Shelves

Use the 7 Connectors/Clips to secure the 3 Wire Mesh Shelves to the structure. Hammer the clips into the designated slots on the 1 Upright Posts.

Step 8: Secure to Wall

For safety, it is recommended to permanently fix the unit to the wall. Use the provided wall anchor hardware (A Nut, B Screw, C Washer) to attach the unit to the wall. Ensure the hardware is suitable for your wall type. The diagram shows the hardware being used to attach the top of the upright posts to the wall.

WARNING: Serious or fatal injuries can occur from furniture tipping over. To prevent the furniture from tipping over, we recommend that it is permanently fixed to the wall. Wall anchor and hardware are included with this product. Please make sure hardware is suitable for your walls before installing, as different wall materials may require different types of anchors.

After-Sales Service

Thank you for trusting our service and products. We guarantee that the product has undergone strict quality inspection and meticulous packaging. If you encounter any issue regarding shipping or the product, please feel free to contact us at any time. We are happy to serve you wholeheartedly.

Yours Sincerely,

• Please avoid harsh, corrosive, and abrasive cleaners.
• Keep dry and avoid damp environments.

If you have any questions or concerns, please feel free to contact us. We are committed to providing our customers with quality service.