PSA Products | Security Systems Wholesale in Australia
User Manual for PSA models including: PAN900SKHD Video Intercom System, PAN900SKHD, Video Intercom System, Intercom System, System
Image Without Border
File Info : application/pdf, 6 Pages, 612.53KB
DocumentDocumentVideo Intercom System User Manual Model: PAN900SKHD Introduction 1 Intercom / Answer 2 Unlock Door 3 Unlock Gate 4 Monitoring / + 5 Settings 6 Do Not Disturb / - Answer call from an external Door Station. Or to hang up a call. Also to call another indoor Monitor. Long press to exit. Activate Electric Door Strike (of the active Door station) Unlock external gate (via rear Unlock port) To view/monitor an external Door Station Also to scroll up, or to increase value. Press to display Settings menu. (Tip: First press Button to wake the Monitor) Do Not Disturb mode (On/Off). Also to scroll down, or to decrease value. System Wiring Diagram Kit includes Monitor 1 and Door Station 1 only. Monitor 4 4C Monitor 3 4C Monitor 2 4C Monitor 1 Door Station 1 (Door1 ) 4C 4C Door Station 2 (DOOR2) 2C Electric Door Strike 2C Electric Door Strike AUDIO (Red) GND (White) DATA (Black) VIDEO (Yellow) System Wiring Diagram Monitor 1 (Rear View) VCC AUDIO GND VIDEO DOOR1 VCC AUDIO GND VIDEO DOOR2 GND 15V DC-IN AUDIO GND DATA VIDEO IN AUDIO GND DATA VIDEO OUT NC COM COM NO UNLOCK Items marked with *** are not included in Kit. Door Station 1 COM (Orange) NO (Green) VCC (Red) AUDIO (White) GND (Black) VIDEO (Yellow) Electric Door Strike *** To GND (Black) Door Station 2 *** COM (Orange) NO (Green) VCC (Red) AUDIO (White) GND (Black) VIDEO (Yellow) Electric Door Strike *** To GND (Black) GND 15VDC 240VAC Power Supply (Monitor 1) Monitor 2 *** (Rear View) NC (Red) COM (Black) COM (White) NO (Yellow) Magnetic lock *** GND 240VAC Power Supply *** 12-18VDC (for Magnetic lock) 12-18VDC 240VAC Power Supply *** GND (for Magnetic lock) Electric Door Strike *** GND 15VDC 240VAC Power *** Supply (Monitor 2) To Next Monitor Wiring Notes · Disconnect power before installation. · Supports up to 4 internal Monitors and 2 external Door Stations. · Keep the Intercom wires more than 30cm away from AC mains power to avoid interference. · The electric door strikes are not included in this Kit. Use 12VDC electric door strikes only. Do not exceed 500mA. Cable Requirements: Wiring distance 50m. Use 4-core cable with a wire diameter of 0.5 mm2 or more. Wiring distance 80m. Use 4-core cable with a wire diameter of 0.75 mm2 or more. CAT5e or CAT6 Network Cable Wiring Configuration: 1. From Door Station(s) to First Monitor RED CAT5e or CAT6*** Brown, Blue BLACK Brown/White Blue/White Green/White Orange/White WHITE Green YELLOW Orange 2. From First Monitor to Additional Monitor(s): RED BLACK CAT5e or CAT6*** Brown, Blue Green WHITE Brown/White Blue/White Green/White Orange/White YELLOW Orange *** Cable Distance up to 50m (measured from external door station to last Monitor in daisy-chain). Installation of Indoor Monitor · Select an eye-level position to mount the Monitor. The recommended height is 150cm - 160cm from floor level. · Keep a distance of 30cm (minimum) from AC Power to avoid electrical interference. Avoid installing near a strong radiation source (eg. TV and computers). Keep the Monitor away from water. · Do not drop, shake or knock the device to avoid damaging the components. · Switch off power supply before installation. Mounting the Monitor on the wall Operating Instructions Visitor Call When the Bell button of an external Door Station is pressed, all indoor Monitors will sound their selected ringtone(s). If unanswered, the Monitors will ring for 16 seconds. The call will automatically terminate after a minute. Answering Call From Door Station Press the Intercom button once to answer an incoming call. Press again to exit. The call will automatically exit after a minute. To decline the call, long press (press and hold) the Intercom button. Monitoring When the Monitor is on Standby, press the Monitor button repeatedly to monitor DOOR1 and DOOR2. While monitoring a Door Station, press the Intercom button once to talk to that Door Station. Long press to exit Monitoring mode. Unlock Press the Unlock button to activate the Electric Door Strike (while the Monitor is showing video from that Door Station). Likewise, press the button to unlock the door that is being monitored. Intercom Call Between Internal Monitors If the system has two or more indoor Monitors, press the Intercom button to call all other Monitors (while on Standby mode). Press the Intercom button at any other Monitor to answer the call. Long press to cancel the intercom call. Settings Menu Press to wake up the Monitor. Then press the Settings button to show the Settings menu. Press repeatedly to step through the parameters. For a displayed parameter, press to increase or to decrease its value. Then press for the next parameter. The parameters are shown in the following sequence: Brightness , Contrast , Ringtone , Ringtone Volume , Intercom Volume and Do Not Disturb (DND) . Long press the buttton to exit. Do Not Disturb (DND) Mode The Do Not Disturb Mode can be turned ON through the Settings menu. When turned on, the icon will appear on the screen. Alternatively, while on Standby, long press the button for 3 seconds to enable or disable the Do Not Disturb mode. The Monitor is silenced when the DND Mode is ON. Specifications Monitor Screen Size Monitor Resolution Video Format Call Mode Call Active Time Working Voltage Stand-by Current Working Current Working Temperature Installation Method Dimensions (H x W x D) Door Station Camera Sensor Camera View Angle Door Station IP Rating Material (Door Station) Dimensions (H x W x D) Packing List Indoor Monitor Outdoor Door Station 15VDC Power Adapter Wall Bracket Screws Wall Plugs Lead - 4 Pin Plug Lead - 2 Pin Plug User Manual 7-Inch LCD 1024 x 600 pixels CVBS/AHD Automatic half duplex 60s (approx.) 15V DC 100mA (max.) 650mA (max.) -10~50ºC Surface mount 125 x 185 x 25mm 2MP (1080p) 110deg Horizontal IP65 Metal Housing 130 x 41.5 x 27mm " 1 pcs 1 pcs 1 pcs 1 pcs 4 pcs 4 pcs 7 pcs 1 pcs 1 pcs Warranty & Liability 1. PSA Products Pty Ltd (ABN: 99 076 468 703) of 17 Millicent Street, Burwood 3125 Victoria, Australia warrants this product for a period of 12 months from the date of purchase, as reflected on the Authorised Resellers or Distributors invoice/ receipt provided to you. PSA Products Pty Ltd will repair or replace the product (at the option of PSA Products) due to any manufacturing defect, at the cost of PSA Products Pty Ltd (excluding any labour costs relating to removal or re-installation of product, and transport costs). 2. This warranty shall not apply to the product if it has been damaged, modified, abused or altered after the date of purchase, or if it fails to operate due to improper maintenance. 3. To the extent permitted by law, the liability of PSA Products Pty Ltd arising from the sale or under the terms of this limited warranty shall not in any case exceed the cost of replacement and subject to this clause. In no case shall PSA Products pty Ltd be liable for consequential loss or damages resulting from the failure of the product or breach of this, or: Any other warranty, express or implied, loss or damage caused by failure to abide by the instructions supplied in the leaflets. 4. To the extent permitted by law, PSA Products Pty Ltd., makes no warranty, expressed or implied, written or oral, including that of merchantability or fitness for any particular purpose, with respect to the consumer replaceable battery if any. A product with nonserviceable builtin battery is covered under warranty of the product as per point 1. 5. This warranty is provided in addition to other rights and remedies you have under law: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. What constitutes a major failure is set out in the Australian Consumer Law. 6. To make a claim under warranty, take the product (with a proof of purchase) to the store where you purchased the product or contact PSA Products Pty Ltd. Phone (03) 9888 9889. or Email: enquiry@psaproducts.com.au with details, proof of purchase or expense claim in writing. PSA Products Pty Ltd 17 Millicent St, Burwood, VIC 3125 Australia T. 1300 772 776 enquiry@psaproducts.com.au psaproducts.com.au