Cheerlux E1 Projector
Model Number: E1
Function Overview
- Connect To WIFI
- Auto Focus
- Electronic Keystone Correction
- BT Settings
- Screen Mirroring Function for iOS & Android System
- Source Selection
Remote Control Instructions
The remote control includes the following buttons:
- Power: Turns the projector on/off.
- Mute: Mutes/unmutes audio.
- F+ / F-: Electronic focus adjustment buttons (F+ for closer focus, F- for further focus).
- OK: Confirms selections or plays media.
- Directional buttons (Up, Down, Left, Right): Navigates menus.
- Volume +/- (VOL-/VOL+): Adjusts audio volume.
- Source: Selects input sources.
- Menu: Opens the main settings menu.
- Return: Goes back to the previous screen or menu.
- EXIT: Exits the current menu or function.
- Pause/Play: Controls media playback.
Note: Battery Not Included.
Operating Instructions
Connect To WIFI
- Select "Settings" on the Home Page.
- Select "Network Settings".
- Turn on "WIFI" and ensure it is connected.
- Enter the password and click "Connect".
Auto Focus
- Select "Settings" on the Home Page.
- Select "Projection Image Settings" and set "Auto Focus" to "On". The projector will enter auto focus mode.
- If the image remains unclear after auto focus, use the "F+/F_" buttons for electronic focus adjustment.
- A visual indicator shows the projector performing auto focus.
Electronic Keystone Correction
- Select "Settings" on the Home Page.
- Select "Projection Settings", then "Advanced Keystone".
- Use the directional arrow keys to adjust the four corners of the image until it is corrected.
BT Settings
- Select "Settings" on the Home Page.
- Select "BT Setting".
- Set "BT" to "Manual Setting" and attempt to match with the correct Bluetooth device.
Screen Mirroring for Android Phone
- On the Home Page, select "Android Cast".
- On your Android phone, select "Screen Mirroring" or "Smart Mirroring" (name may vary by phone model).
- Choose "E1" from the list of devices to share your screen with the projector.
Screen Mirroring For IOS System
- Click "IOS WiFiCast" on the main page, ensuring the projector and iOS device are connected to the same Wi-Fi network.
- On your iOS device, find "Screen Mirroring" and select it to share the screen with the projector.
- Choose "E1" from the list of devices.
IOS Cable Cast
- Connect the Lightning connector from your phone to the projector.
- On your phone, click "Trust" when the prompt appears.
- Enter the device password if required.
Source Selection
- Select "SOURCE" on the main page to enter the signal source interface.
- Choose the desired input source.
Packing List
The package typically includes:
- Projector
- User Manual
- Remote Control
- Power Cable
- HD Cable
Projection Size and Media Formats
Projection Size and Distance
| Screen Size | Projection Distance (m) |
|---|---|
| 50 inches | 1.43 |
| 70 inches | 1.96 |
| 100 inches | 2.78 |
| 120 inches | 3.32 |
Note: The above data is for reference only; please refer to actual measurements. Aspect Ratio: 16:9
Multimedia File Specification
Image Format Support
- File Extension: .jpg, .png, .bmp
- Supported formats: JPEG, PNG, BMP, MPO
Audio Format Support
- File Extension: .avi, .ts, .dat, .vob, .wav, .mkv, .mp3, .mp4, .m4a
- Supported formats: MPEG1, MPEG2, LPCM, MP3
- Does not support: Dolby AC3/AAC, DTS, WMA, DivX, etc.
Video Format Support
- File Extension: .avi, .ts, .dat, .vob, .wav, .mkv, .mp3, .mp4, .m4a, .wmv, .asf, .flv, .3gp, .3gpp, .tp, .trp
- Supported formats: MPEG1, MPEG2, H.263, H.264, AVS, VC1, MJPEG, RV30, RV40, HEVC
- Video Bit Rate: Up to 30-40 Mbps
- Does not support: MSVC/CRAM, MP42, GMC, IV32, RLE, cvid, RV20, DivX, RM, RMVB, FLV, etc.
Warranty Card
Fields for warranty registration:
- User info: Username, Contact Number, Zip Code, Mailing Address
- Product Information: Product Name, Product Number, Product Serial Number
- Sales Information: Sales Unit, Contact Number, Zip Code, Address, Sale Date, Installation And Commissioning Date, Invoice Number
- Delivery Date:
- Maintenance Staff Signature:
- Cause of Issue:
- Troubleshooting:
- Service Point:
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
