BDI Furniture | Designed for Modern Living
Caring for BDI’s Satin-Etched Glass | BDI FurnitureRegister Your BDI Product | BDI FurnitureLimited Warranty | BDI FurnitureThe Distinction, Diversity and Durability of Natural Wood | BDI Furniture
Instruction Manual for BDI models including: MESA 7639 Modern Storage Sideboard, MESA 7639, Modern Storage Sideboard, Storage Sideboard, Sideboard
14 nov. 2023 — Congratulations on the purchase of your Mesa/Ripple Credenza from BDI. Your credenza has been designed to provide a lifetime of enjoyment.
File Info : application/pdf, 12 Pages, 1.82MB
DocumentDocumentMESATM 7639 | RIPPLETM 7629 CREDENZA INSTRUCTION MANUAL LET'S GET STARTED. DESIGN JASON GUIDRY Mesa Ripple Congratulations on the purchase of your Mesa/Ripple Credenza from BDI. Your credenza has been d esigned to provid e a lifetime of enjoyment. This manual will provid e assembly instructions and other helpful information to ensure you get the most out of your product. Please save it for future reference. Your Mesa/Ripple Cred enza has been engineered for simple assembly. Please follow these directions carefully to prevent any damage. Should you need further assistance, contact BDI at customerservice@bdiusa.com. ENJOY! NEED ASSISTANCE? customerservice@bdiusa.com | 3 HHAARDRDWWAAREREAANNDDCOCOMMPOPONNENENTSTS Unpack and id entify the parts listed below. The assembly workspace should be a non-marring surface, such as carpet. For missing hard ware pieces, please contact BDI Customer Service at customerservice@bdiusa.com. For all other concerns, please contact your BDI retailer. Do not use power tools for the assembly of this product. TOOL REQUIRED (NOT INCLUDED) Phillips Screwdriver Hex Wrench (T1) QTY: 1 Screw M6 x 16 (H1) QTY: 8 Screw M6 x 70 (H2) QTY: 6 Wood Screw (H3) QTY: 8 HARDWARE REQUIRED (NOT INCLUDED) Drywall Anchor HARDWARE REQUIRED (NOT INCLUDED) Drywall Screw Spanner Tube (C1) QTY: 2 Leg (C2) QTY: 2 Mesa Cabinet (C3) Ripple Shelf (C5) 4 | BDIUSA.COM QTY: 1 Door Pull (C4) QTY: 4 *Pre-installed on the unit QTY: 2 Wall Anchor Strap* (C6) QTY: 1 MESA 7639 | RIPPLE 7629 STEP 1. ASSEMBLE BASE To assemble the Base, lay the Spanners (C1) on a soft, non-marring surface, like carpet. Attach the Legs (C2) to the Spanners (C1) using 8 Screws (H1) and tighten with Hex Wrench (T1). C2 C1 H1 STEP 2. ATTACH BASE TO CABINET Lay the Cabinet (C3) on a soft, non-marring surface, like carpet. Attach the Base to the Cabinet (C3) using 6 Screws (H2) and tighten with Hex Wrench (T1). ASSEMBLY HEX WRENCH T1 QTY 1 SCREW H1 QTY 8 C2 H1 ASSEMBLY HEX WRENCH T1 QTY 1 SCREW H3 QTY 6 C3 (Ripple shown) H2 H2 H2 H2 H2 H2 NEED ASSISTANCE? customerservice@bdiusa.com | 5 ASSEMBLY STEP 3. INSTALL DOOR PULLS With the help of another person, carefully turn the Cabinet onto its Base. Open the doors and connect the 4 Door Pulls (C4) with 8 Wood Screws (H3). Tighten with Phillips Head Screwdriver (not included). (Mesa shown) H3 C4 C4 C4 H3 NOT INCLUDED QTY PHILLIPS SCREWDRIVER 1 SCREW H3 QTY 8 C4 H3 ASSEMBLY STEP 4. REPOSITION / INSTALL SHELVES To adjust the shelf positions remove the Shelves (C5) by lifting and tilting them, then pulling them out of the cabinet. Adjust the shelf pins as needed. Replace the Shelves (C5) by tilting them and placing them on the shelf pins. C5 6 | BDIUSA.COM MESA 7639 | RIPPLE 7629 STEP 5. REMOVE & RE-INSTALL DRAWERS (OPTIONAL) Your cabinet shipped with the drawers installed in their upper positions. The user can also move them to a lower position in the cabinet. If you want to change the location of the drawers, remove them from their drawer slides. Look under the drawer and find the plastic pin on each drawer slide. Pull the plastic pins out, and gently lift each drawer up and towards you to remove them. ASSEMBLY Note that the hole in the drawer side is to allow for hinge adjustment (see page 10). (Pin Pushed In) Pin Pulled Out NEED ASSISTANCE? customerservice@bdiusa.com | 7 ASSEMBLY STEP 6. REMOVE DRAWER SLIDE BRACKETS Remove the screws holding Drawer Slide Brackets in place using a Hex Wrench (T1). Relocate the Drawer Slide Brackets to the HEX WRENCH T1 QTY 1 desired position, and reinsert the screws, tightening with the Hex Wrench (T1). Perform Step 5 in reverse order to reinstall the Drawer in the desired location. 8 | BDIUSA.COM MESA 7639 | RIPPLE 7629 STEP 7. ANCHOR THE CABINET ASSEMBLY With help from another person, carefully walk the cabinet into the desired position against the wall. It is strongly recommended that you anchor your cabinet to the wall using the provided Anchor Strap (C6). Use painter's tape to mark the upper left corner of the unit, as shown. NOT INCLUDED QTY WALL ANCHOR 1 NOT INCLUDED QTY WALL SCREW 1 With help from another person, carefully move the cabinet away from the wall. Measure and mark the wall as shown. Attach one end of the Anchor Strap (C6) to the wall at the marked location with an appropriate wall anchor and screw (not included). 39.75" 1,010 mm 32" 813 mm NEED ASSISTANCE? customerservice@bdiusa.com | 9 FINE TUNING ADJUST DOOR HINGES (IF NEEDED) These steps are to be followed after you have unpacked and completed the simple assembly instructions for your console. Due to jostling in freight or perhaps an uneven floor, the doors on your cabinet may not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. The high-quality European hinge hardware is adjustable. Through a little adjustment, you can modify the orientation of the cabinet doors to make sure that they are sitting perfectly on your unit. The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing against the door frame. If NOT INCLUDED QTY PHILLIPS SCREWDRIVER 1 the cabinet's doors appear out of alignment, this condition can be corrected with minor adjustment to the European hinges on each door. Because these hinges are adjustable, adjusting one hinge element can sometimes cause the need for adjustments to other elements. But with a few adjustments, you can modify the orientation of the cabinet doors to make sure that they hang perfectly within your cabinet. Use a Phillips Screwdriver (T1) to adjust the door hinges: n By adjusting Screw 1, the door will move LEFT or RIGHT within the frame. Make minor adjustments at both top and bottom hinges for best results. n By adjusting Screw 2, the door will move UP or DOWN. n By adjusting Screw 3 the entire door will move IN or OUT, opening or closing the gap between the door frame and cabinet. (This screw rarely needs adjustment.) Tightening Screw 1 on top hinge will open the seam between Door C & Door D here Loosening Screw 1 on this hinge will close the seam between Door C & Door D here 1 2 3 Door A Door B Door C Door D Door C 10 | BDIUSA.COM MESA 7639 | RIPPLE 7629 CARE & MAINTENANCE Your BDI furniture has been constructed with the finest materials, carefully manufactured , and designed to last a lifetime. Regular furniture care will prolong your enjoyment and keep it looking its best. Here are some general tips for taking care of BDI furniture. Your surfaces may vary. GLASS Glass surfaces are maintained using household glass cleaner and a paper towel or cloth. SATIN-ETCHED GLASS This uniquely smooth-to-the-touch glass surface can be regularly maintained using household glass cleaner and a paper towel or cloth. A `Magic Eraser' removes minor scratches or scuffs not eliminated using a paper towel or cloth. `Magic Eraser' is a melamine foam prod uct available at any grocery store or home improvement center. Dampen the entire glass surface and the Magic Eraser, then rub the whole surface in broad , even strokes using moderate pressure. Clean and dry the surface with a paper towel. Check for results and repeat as necessary. Any scratches or scuffing not eliminated by one of the above methods can often be ad d ressed by `refreshing' the glass. This process should not be required more than once per 612 months. See this brief video for the simple method: www.bdiusa.com/glass WOOD Wood surfaces should be cleaned with a slightly damp (not saturated) cloth or paper towel. Do not use glass cleaner on wood. If moisture remains, dry the surface with another cloth. If needed, a gentle, non-abrasive cleanser may be used, but wipe away all cleaner residue and dry the surface with a cloth. BDI's wood finishes feature natural hardwood solids and veneers. Wood is a product of nature and-- unlike man-mad e materials that can be manufactured to strict and consistent specifications--has natural imperfections that are part of its appeal and character. Every piece of wood differs from every other, even when coming from the very same tree. As such, grain, texture, and tone variation should be expected from one panel or piece of furniture to the next. While BDI's stained wood finishes are stable in tone & appearance, all finishes are subject to some degree of discoloration with prolonged exposure to direct sunlight. Please avoid positioning your BDI cabinet in any area with ample direct sunlight. To learn more about the features of natural wood, visit www.bdiusa.com/wood METAL, PORCELAIN, & PAINTED SURFACES Surfaces should be cleaned with a slightly d amp (not saturated ) cloth or paper towel. If moisture remains, dry the surface with another cloth. If needed, a gentle, non-abrasive cleanser may be used, but be sure to wipe away all cleaner residue and dry the surface with a cloth. NEED ASSISTANCE? customerservice@bdiusa.com | 11 WARRANTY BDI warrants to the original purchaser that for the below-stated warranty term, BDI will replace any product, part, or component covered by this warranty that fails under normal use as a result of a defect in material or workmanship. The decision to replace a complete product versus the part or component in question will be at BDI's sole discretion. Residential Use: BDI Furnishings carry warranty coverage for three (3) years from the date of product delivery, as shown on your sales receipt/documentation. Select chairs carry coverage for five (5) years from the date of product delivery. Commercial Use: BDI Furnishings carry warranty coverage for one (1) year from the date of product delivery, as shown on your sales receipt/documentation. Select chairs carry coverage for five (5) years from the date of the product delivery, based on an 8-hour daily use pattern. BDI reserves the right to refine or update its warranty from time to time. See the complete and latest warranty document at www.bdiusa.com/warranty. PRODUCT REGISTRATION Registering your new BDI product allows us to send you important product updates, service information, and helpful hints related to your BDI products. Register today, and you will be entered to win free a BINK table from BDI: www.bdiusa.com/register These distinctive product configu ations are protected by US and international patents, trade dress, and/or copyright laws. Mesa, Ripple, & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2023, BDI | V.11.14.2023 Made in China.