TV Mounts, Stands, Monitor Mounts, Stands & More | MOUNTUP
Installation Guide for MOUNTUP models including: B0CPPRTGSB, B0CC8B8YQ9, B0CC8CB4WL, B0CC8NZVMY, B0CC89BKND, B0CPPRTGSB Height Adjustable Electric Standing Desk, Height Adjustable Electric Standing Desk, Adjustable Electric Standing Desk, Electric Standing Desk, Standing Desk, Desk
MOUNTUP Height Adjustable Electric Standing Desk, 48 x 24 Inches Whole-Piece Sit Stand Desk, Quick Assembly Stand Up Desk with Memory Controller, Ergonomic Desk, Black
User Manual (PDF) MOUNTUP MOUNTUP,Height,Adjustable,Electric,Standing,Desk,,48,x,24,Inches,Whole-Piece,Sit,Stand,Desk,,Quick,Assembly,Stand,Up,Desk,with,Memory,Controller,,Ergonomic,Desk,Rustic,Brown,B0CPPRTGSB,B0CC8B8YQ9,B0CC8CB4WL,B0CC8NZVMY,B0CC89BKND
UP101-1 User Manual (PDF) MOUNTUP MOUNTUP,Height,Adjustable,Electric,Standing,Desk,Whole-Piece,48,x,24,Inches,Quick,Assembly,Sit,Stand,Desk,with,Memory,Controller,Black,48x24"WholePiece,Black,B0CPPRTGSB,B0CC8B8YQ9,B0CC8CB4WL,B0CC8NZVMY
File Info : application/pdf, 12 Pages, 2.50MB
DocumentDocumentElectric Height Adjustable Standing Desk Installation Manual max 48 inch min 29 1/8 inch 154 lbs / 70 kg V2.0 Technical Support: 626-425-4350, Mon-Fri, 10am-6pm (PST) Other Info: help@jollyholding.com Website: https://mountup.com If you have any issues, please feel free to contact our customer support before returning. At MOUNTUP strive to provide you with the best quality products and services in the industry. SAFETY INSTRUCTIONS BEFORE ASSEMBLY . WARNING controller. KEEP AWAY . uct. YEARS OLD. T . USE & LIABILITY . W ELECTRICAL SAFETY . T the . WARNING PINCH POINT MCT . CAUTION Do not exceed desk weight limit. Keep the knee space clear obstacles. Keep weight on desk balanced for correct operation and longer life of components. Leave enough slack in cables to allow for full range of vertical motion. Failure to follow these instructions may result in property damage and / or personal injury. 1 PACKAGE CONTENTS A (×1) Tabletop B(×1) Frame C(×2) Side Bracket D (×2) Base E (×2) Hook F (×1) Power Adapter G (×1) Controller H (×1) Power Wire SCREW & BOLT KITS I (×2) Grommet M-A(×10) M-B (×8) M-C (×4) M-D (×6) M-E (×1) M6×14 Bolt M6×20 Bolt M6×12 Bolt ST4.8×12 Screw 4mm Allen Key 2 M-F (×4) Cable Clip M-G (×1) Screwdriver ASSEMBLY STEPS Installation Tips Lay a mat or old blanket underneath desk so the floor and the furniture will not get scratched or damaged during assembly. STEP 1 Attach Side Bracket (C) to Frame (B)with 4 pcs of M6x12 Bolt (M-C). Tighten them with Allen Key (M-E). M-E M-C C Pay attention to the direction of Side Bracket (C) . C B 3 STEP 2 Attach Base (D) on Frame (B). Use 8 pcs of M6x20 Bolt (M-B) and Allen Key (M-E) to tighten them. M-E D D M-B B 4 STEP 3 1. Place and align Frame (B) to Tabletop (A). Use 10 pcs of M6x14 Bolt (M-A) and Allen Key (M-E) to tighten them. M-E M-A B A M-G M-D E E 2. Attach Hook (E) to Tabletop (A). Use Screw (M-D) and Screwdriver (M-G) to tighten them. 5 STEP 4 Note: The Controller should be installed close to the motor. 1. Put Controller (G) on the Tabletop (A) and align it with pilot holes. Use Screw (M-D) and Screwdriver (M-G) to tighten them. M-G M-D G Motor A M-G M-D F 2. Align Power Adapter (F) with the pilot holes, and then tighten it with Screw (M-D) and Screwdriver (M-G). 6 STEP 5 1. Connect the motor wire to Controller (G). 2. Connect the wire of Power Adapter (F) to Controller (G). 3. Connect Power Wire (H) to Power Adapter (F). Motor to Controller G 1 G B Motor 2 F G Power Adapter to Controller 3 H F Power Wire to Power Adapter 7 STEP 6 Attach Cable Clip (M-F) to the backside of Tabletop (A) for cable management. 1 Tear off the plastic film. M-F 2 Stick them to the tabletop. Motor 3 Fasten cables with the cable clips. STEP 7 1. Turn over the desk to stay upwards and insert Grommet (I). 2. Make sure the legs are level and all bolts are well tightened to avoid the desk making noise or wobbling. 3. Plug in the power supply and get the desk power on. I Note: If the desk is unlevel from the bumpy floor, you may loose or tighten the base pad to level it 8 Operation Guide Program Reset To reset the program, press and hold the" " button until the desk move to the lowest height and the screen shows " ", then release. Height Adjustment Press and hold " " to raise the desk, press and hold " " to lower the desk. The height will be showed on the screen. Preset Memory Height When the desk moves to desired height, press and hold button "1" for 3 seconds, when "S-1" is dispayed, the current height is saved as H1. Continue the same step to preset button 2 as H2 memory height. Adjust to Preset Height Set Child Lock Press the 1 or 2 button, the desk will automatically move to the preset memory height. Press and hold both buttons " " & " " for 5 seconds, the desk will be locked when "Loc" is displayed on the screen. You can press and hold both button " " & " " for 5 seconds to unlock it. Anti-collision Protection Desk will retract if encounters obstacle during its vertical movement. Please make sure no obstacle under or above desk's moving scope. 9 Operation Guide Set Anti-collision Sensitivity The anti-collision sensitivity of the desk defaults to 2. If you need to set the sensitivity, please do the following steps. -Press and hold "1" and "2" for more than 20 seconds, until the controller screen flashes, the system can start setting. -Press button "1" and "2" simultaneously, you can select the menu: U-0 and d-0. rd anti-collision sensitivity. rd anti-collision sensitivity. -Pr rOm 0-9 (0 means no sensitivity, 9 means the highest sensitivity). -Press and hold "1" and "2" for 5 seconds, when the screen shows , the modified content is saved. 10 Product Dimensions 2630c3m/5in 471210/4cimn 29 1/8-48in 74-122cm 6203c5m/8in T Lowest Height Highest Height Weight Capacity Tabletop Size Input Voltage Travel Speed Applicable Temperature Noise 29 1/8in (74cm) 48in (122cm) 154 lbs (70Kg) 47 1/4in × 23 3/5in × 5 /8in 120cm × 60cm × 1.5cm AC 100-240V 20mm/s 0~40 11