ROHM BD728x-LB Voltage Follower DC Sweep Simulation User Guide

User Guide for ROHM models including: BD728x-LB Voltage Follower DC Sweep Simulation, BD728x-LB, Voltage Follower DC Sweep Simulation, Follower DC Sweep Simulation, DC Sweep Simulation, Sweep Simulation

BD728x-LB – Voltage Follower – DC Sweep simulation

Rev.001

ROHM CO., LTD.

ROHM Solution Simulator | ROHM Semiconductor - ROHM Co., Ltd.

BD728x-LB – Voltage Follower – DC Sweep simulation

File Info : application/pdf, 4 Pages, 629.59KB

scheminfo bd728x-lb voltage follower opamp dcsweep ug-e

User's Guide
ROHM Solution Simulator
Low Noise Rail-to-Rail Input/Output High Speed CMOS Operational Amplifiers
BD728x-LB Voltage Follower DC Sweep simulation
This circuit simulates DC sweep response with Op-Amp as a voltage follower. You can observe the output voltage when the input voltage is changed. You can customize the parameters of the components shown in blue, such as VSOURCE, or peripheral components, and simulate the voltage follower with the desired operating condition.
You can simulate the circuit in the published application note: Operational amplifier, Comparator (Tutorial). [JP] [EN] [CN] [KR]
General Cautions Caution 1: The values from the simulation results are not guaranteed. Please use these results as a guide for your design. Caution 2: These model characteristics are specifically at Ta=25°C. Thus, the simulation result with temperature variances may significantly differ from the result with the one done at actual application board (actual measurement). Caution 3: Please refer to the Application note of Op-Amps for details of the technical information. Caution 4: The characteristics may change depending on the actual board design and ROHM strongly recommend to double check those characteristics with actual board where the chips will be mounted on.
1 Simulation Schematic

Figure 1. Simulation Schematic
2 How to simulate
The simulation settings, such as parameter sweep or convergence options, are configurable from the `Simulation Settings' shown in Figure 2, and Table 1 shows the default setup of the simulation.
In case of simulation convergence issue, you can change advanced options to solve. The temperature is set to 27 °C in the default statement in `Manual Options'. You can modify it.

Simulation Settings

Simulate

Table 1. Simulation settings default setup

Parameters

Default

Simulation Type

Parameter Sweep

VSOURCE

Advanced options

Balanced Convergence Assist

Manual Options

.temp 27

Figure 2. Simulation Settings and execution
Note Do not change Simulation Type VOLTAGE_LEVEL from 0 V to 5 V by 0.1 V -

No. 66UG024E Rev.001
Jun.2023 1/3

BD728x-LB Voltage Follower DC Sweep simulation

User's Guide

3 Simulation Conditions

Table 2. List of the simulation condition parameters

Instance Name

Type

Parameters

Voltage_level

VSOURCE Voltage Source AC_magnitude

AC_phase

VDD

Voltage Source For Op-Amp

Voltage_level AC_magnitude AC_phase

(Note 1) Set it to the guaranteed operating range of the Op-Amps.

Default Value
5 0.0 0.0 5 0.0 0.0

Variable Range

Min

Max

5.5

fixed

2.5(Note1) 5.5(Note1)

fixed

Units
V V ° V V °

4 Op-Amp model

Table 3 shows the model pin function implemented. Note that the Op-Amp model is the behavioral model for its input/output characteristics, and neither protection circuits nor functions unrelated to the purpose are implemented.

Table 3. Op-Amp model pins used for the simulation

Pin Name

Description

+IN

Non-inverting input

-IN

Inverting input

VDD

Positive power supply

VSS

Negative power supply / Ground

OUT

Output

No. 66UG024E Rev.001
Jun.2023 2/3

BD728x-LB Voltage Follower DC Sweep simulation

User's Guide

5 Peripheral Components

5.1 Bill of Material Table 4 shows the list of components used in the simulation schematic. Each of the capacitors has the parameters
of equivalent circuit shown below. The default values of equivalent components are set to zero except for the ESR of C. You can modify the values of each component.

Table 4. List of capacitors used in the simulation circuit

Type

Instance Name

Default Value

Resistor

R1_1 RL1

0 10k

Capacitor

C1_1 CL1

0.1 25

Variable Range

Min

Max

1M, NC

0.1

free, NC

Units
k pF pF

5.2 Capacitor Equivalent Circuits

(a) Property editor

(b) Equivalent circuit

Figure 3. Capacitor property editor and equivalent circuit

The default value of ESR is 2m . (Note 2) These parameters can take any positive value or zero in simulation but it does not guarantee the operation
of the IC in any condition. Refer to the datasheet to determine adequate value of parameters.

6 Recommended Products

6.1 Op-Amp

BD7282FVM-LB : Low Noise Rail-to-Rail Input/Output High Speed CMOS Op-Amps. [JP] [EN] [CN] [KR] [TW] [DE] BD7284F-LB : Low Noise Rail-to-Rail Input/Output High Speed CMOS Op-Amps. [JP] [EN] [CN] [KR] [TW] [DE]

Technical Articles and Tools can be found in the Design Resources on the product web page.

No. 66UG024E Rev.001
Jun.2023 3/3

Notice
Notice
1) The information contained in this document is intended to introduce ROHM Group (hereafter referred to asROHM) products. When using ROHM products, please verify the latest specifications or datasheets before use.
2) ROHM products are designed and manufactured for use in general electronic equipment and applications (such as Audio Visual equipment, Office Automation equipment, telecommunication equipment, home appliances, amusement devices, etc.) or specified in the datasheets. Therefore, please contact the ROHM sales representative before using ROHM products in equipment or devices requiring extremely high reliability and whose failure or malfunction may cause danger or injury to human life or body or other serious damage (such as medical equipment, transportation, traffic, aircraft, spacecraft, nuclear power controllers, fuel control, automotive equipment including car accessories, etc. hereafter referred to as Specific Applications). Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses, or losses incurred by you or third parties arising from the use of ROHM Products for Specific Applications.
3) Electronic components, including semiconductors, can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against physical injury, and damage to any property, which a failure or malfunction of products may cause.
4) The information contained in this document, including application circuit examples and their constants, is intended to explain the standard operation and usage of ROHM products, and is not intended to guarantee, either explicitly or implicitly, the operation of the product in the actual equipment it will be used. As a result, you are solely responsible for it, and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses, or losses incurred by you or third parties arising from the use of such information.
5) When exporting ROHM products or technologies described in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, such as the Foreign Exchange and Foreign Trade Act and the US Expor t Administration Regulations, and follow the necessary procedures in accordance with these provisions.
6) The technical information and data described in this document, including typical application circuits, are examples only and are not intended to guarantee to be free from infringement of third parties intellectual property or other rights. ROHM does not grant any license, express or implied, to implement, use, or exploit any intellectual property or other rights owned or controlled by ROHM or any third parties with respect to the information contained herein.
7) No part of this document may be reprinted or reproduced in any form by any means without the prior written consent of ROHM.
8) All information contained in this document is current as of the date of publication and subject to change without notice. Before purchasing or using ROHM products, please confirm the latest information with the ROHM sales representative.
9) ROHM does not warrant that the information contained herein is error-free. ROHM shall not be in any way responsible or liable for any damages, expenses, or losses incurred by you or third parties resulting from errors contained in this document.

Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
https://www.rohm.com/contactus

R2043A

References

Microsoft Word for Microsoft 365