Instruction Manual for VGC models including: BHM-79 Speaker Microphone, BHM-79, Speaker Microphone, Microphone
12 juil. 2024 — INSTRUCTION MANUAL. BHM-79. Page 2. 1,Product overview. P1. PTT. P3. Type-C. P2. Key ... Please NOTE that this speaker microphone is not an official headset for ...
BHM-79 INSTRUCTION MANUAL 1,Product overview P1 P2 PTT P3 Key func on introduc on: Type-C 1,+ - Key Short Press: Incress or decress Channel Long Press:Con nuously increase/decrease channels Double Click :When the Bluetooth speaker is playing music, switch between the previous song and the next song. 2,P1 Key Short Press: Decrease Volume Long Press: A/B Band Switch Double Click : Mute/ Unlock Mute 3,P2 Key Short Press: Incress Volume Long Press : Talk Around ON/OFF Press P1+P2 : Send 1750Hz Brust Tone 4,P3 Key Short Press:Report Current Channel Long Press: Turn On /OFF Double Click : Enter Pair Status When the speaker microphone is connected to the Bluetooth system of the mobile phone and a call comes in, Short Press the P3 bu on to answer the call, and Double-Click the P3 bu on to hang up the call. When you are on a call, Short Press the P3 bu on to hang up the call. Please NOTE that this speaker microphone is not an official headset for calls, so when you answer the call, the call sound quality will be poor. Try to use your mobile phone to answer the call. 2,Remove belt clip Li the buckle and push down to remove the belt clip 3,LED Status Status Device not connected Low voltage alarm Enter pairing state A er successful pairing disconnect to device mute state Radio TX status Radio RX status Charging status Fully charged state Red flash slowly flash quickly flash alternately double flash Always on Always on Green flash alternately double flash color gradient Always on Always on 4,Pair To The Radio 1,Long press the <p3> key to turn on the microphone, then double click the <p3> key to enter pairing state. the indicator light of the microphone flashes red and blue alternately, and a beep sounds to indicate that it has entered the pairing state 2,Turn on the radio,switch the menu to General Se ngsBluetooth Se ngs on radios.Select Pairing to enter pairing state. 3,BHM-79 will be displayed in the list of available devices on radios, select BHM-79 and bind it 5,Pair On The APP 1,Press and hold the <P3> bu on to turn on the microphone to be paired, and then double-click the <P3> bu on. The indicator light of the microphone flashes red and blue alternately, and a beep sounds to indicate that it has entered the pairing state. 2,Open the APP to enter the se ngs page, click Connec on Management, and turn on scanning. 3,Find the BHM-79 in the scanned list and click BHM-79 to pair. If pairing is unsuccessful, please repeat the above steps, or the speaker microphone has been mistakenly paired to surrounding radios, please turn off other radio and pair with this device again. When the pairing is successful, <Peripheral Pairing> will automa cally turn of the pairing state. Observe whether the headset icon is displayed on the display of the radio, or press the PTT bu on. The display will display the upward transmi ng icon. A er releasing the PTT, the microphone will make a "beep" sound tone. 6,Upgrade Steps 1,Open the Bluetooth page of the cell phone and connect the speaker microphone BHM-79 (as shown in the figure 1 below) 2. Open the APP and press the PTT of BHM-79,Click the three dots in the upper right corner to enter the BHM-79 se ngs page (Figure 2) Figure 1 Figure 2 3. Pop up the upgrade menu to upgrade Precau ons: 1. The effec ve communica on distance of speaker microphones is less than 10 meters. Use beyond the range will cause the speaker microphone to transmit and receive abnormally. 2. A er the wireless microphone is turned on, it will automa cally search for the last paired radio. When the paired radio fails to connect, the wireless mic -rophone will automa cally turn of f a er 3 Minutes to save power. If the connec on is normal, it will prompt that it is connected and can be used. During use, the paired radio goes offline, and the speaker microphone prompts that the connec on has been disconnected. 3. When the speaker microphone prompts that the ba ery is low, please charge the speaker microphone in me. Con nued use will cause the speaker mic -rophone voltage to be lower than the protec on value and shut down. While charging, the indicator light shows red and turns blue when fully charged. Specifica ons Model:BHM-79 Wireless Speaker Microphone TX&RX frequency: 2.4~2.485GHz ISM band Effec ve distance: <10 meters Power supply mode: built-in 1200mA lithium ba ery Voltage:3.7V(Use a 5V@1A rated output power adapter to charge) Weight:115g Size: 98.5(L)x69.5(W)x30(D) Copyright © 2024 by VEROTELECOMCorel PDF Engine Version 24.5.0.731 CorelDRAW 2022