CASIO Module No.

IMPORTANT INFORMATION - READ FIRST

Water Resistance

For all categories of watches, the following are prohibited:

• Pressing buttons underwater;
• Adjusting hands underwater;
• Unscrewing the crown underwater;

If the watch is exposed to salt water, rinse it thoroughly and dry it. Do not wear a watch with a leather strap while swimming. Avoid prolonged contact of the leather strap with water.

Watches are classified into ratings (from I to V) according to their degree of water resistance. Check your watch's rating using the table below to determine its correct usage.

Notes

• Rating I: Watches are not water-resistant. Avoid any moisture.
• Rating II: WR (Water Resistant) means the watch is water-resistant according to ISO 2281. Brief contact with water will not cause any problems.
• Rating III: Water resistance of 5 Bar (50 meters) means the watch can withstand water pressure as indicated and can be used while showering and for brief swimming.
• Rating IV: Water resistance of 10 Bar (100 meters) means the watch can be used for normal swimming and snorkeling.
• Rating V: Water resistance of 20 Bar (200 meters) means the watch can be used for scuba diving (excluding dives requiring helium-oxygen mixtures).

When using the product in conditions of rapid temperature changes, slight condensation may form on the inside of the glass. This phenomenon is due to the laws of physics and is not a defect.

CASIO COMPUTER CO., LTD is not responsible for any damage that may occur during the use of this watch and does not accept any claims from third parties.

Your watch may differ slightly from the illustrations in this manual.

Note

• Some water-resistant models are equipped with a screw-lock crown.
• To pull out such a crown, you must unlock it by turning it in the direction indicated in the illustration. Do not apply excessive force when pulling out the crown. This may lead to damage.
• Note that the watch becomes unprotected from water and moisture when the crown is pulled out. After completing all operations using the crown, return it to its original position and lock it.

Illustration showing a watch crown with a 'G' symbol indicating a lock/unlock direction.

MODULES 1362, 1398, 1770, 2799, 3378, 4370

Setting the Current Time

Pull out the crown. Turn it to set the hands to the current time. Push the crown back to its original position.

Illustration of a watch face with a crown labeled 'Crown'.

MODULES 705, 706, 1300, 1311, 1330, 1344, 1360, 1399, 1747, 1771, 1782, 4328, 4394, 4747, 5049, 5284, 5361, 5364, 5375, 5577

Setting the Current Time

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Turn the crown to set the hands to the current time. Set the minute hand 4-5 minutes ahead of the current time, then move it back.
3. When the time signal sounds, close and secure the crown.

Illustration of a watch face with a crown. Illustration of a watch face showing module numbers 5284, 5361, 5364, 5375, 5577.

MODULES 707, 708, 1331, 1332, 1335, 1336, 1342, 1345, 1346, 1369, 1370, 1373, 1701, 1710, 1711, 1787, 2717, 2718, 2719, 2725, 2731, 2748, 2749, 2783, 2784, 3363, 3711, 3712, 4393, 5025, 5044, 5058, 5116, 5128, 5180, 5199, 5206, 5207, 5218, 5250, 5340, 5341, 5342, 5343, 5352, 5358, 5383, 5393, 5436, 5507, 5532

Setting the Current Time

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Turn the crown to set the hands to the current time. For more precise time setting, move the minute hand back 4-5 minutes from the desired value, then move it forward to the current value.

Illustration of a watch crown showing 'First click: Date setting' and 'Second click: Time setting', with 'Crown (normal position)' indicated.

Setting the Date

• To ensure the date changes at midnight, do not perform date setting between 8:00 PM and 2:00 AM.

1. Pull out the crown to the first click.
2. Turn it to set the desired date.
3. Push the crown back to its original position to resume time display.

Module numbers for this date setting procedure: 5128, 5180, 5199, 5206, 5207, 5218, 5250, 5340, 5341, 5342, 5343, 5352, 5358, 5383, 5393, 5436, 5507, 5532

MODULES 709, 1309, 1333, 1334, 1347, 3716, 5125, 5167, 5223, 5237, 5249, 5339, 5373, 5458, 5474

Setting the Current Time

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Turn the crown to set the hands to the current time. For more precise time setting, move the minute hand back 4-5 minutes from the desired value, then move it forward to the current value.

Illustration of a watch face showing 'First click: Date and Day setting', with 'Crown (normal position)' indicated. Example shows 'SUN 30'.

Illustration of a watch face showing 'First click: Date and Day setting', with 'Crown (normal position)' indicated. Example shows 'WED 30'.

Second click: Time setting.

Module numbers for these diagrams: 709, 1333, 1347, 3716

Setting the Date and Day of the Week

• To ensure the date and day of the week change at midnight, do not perform date setting between 8:00 PM and 2:00 AM.

1. Pull out the crown to the first click.
2. Set the date by turning the crown counter-clockwise.
3. Set the day of the week by turning the crown clockwise. Days of the week are indicated in English or Spanish.

4. Push the crown back to its original position.

WATCHES WITH BACKLIGHT

• Press and hold button L to illuminate the watch face.
• Depending on the watch model, the backlight duration is 2 to 3 seconds, 1 second, or until button L is pressed (Module 5577).
• Depending on the watch model, the backlight is provided by electroluminescent (EL) elements or LEDs. EL elements lose power after extended use.
• Frequent use of the backlight shortens battery life.
• Turning on the backlight for an extended period or with a low battery charge may cause the watch hands to stop moving for a while.

Illustration of a watch face showing 'L (Backlight Button)' and 'Crown'.

Illustration of a watch face showing 'L (Backlight Button)' and 'Crown'.

WATCHES WITH ROTATING BEZEL

Turn the bezel to align the mark with the minute hand. After some time, you can tell how much time has passed since you aligned the mark with the minute hand.

Illustration of a watch bezel with markings for elapsed time measurement.

TECHNICAL SPECIFICATIONS

Technical specifications are subject to change without prior notice.

PRODUCT INFORMATION

Name: Wrist electronic / electro-mechanical quartz watches (men/women)

Brand: CASIO

Manufacturer: CASIO COMPUTER Co., LTD. (CASIO COMPUTER Co., Ltd.)

Manufacturer's Address: 1-6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan

Importer: OOO "Kasio", 127015, Russia, Moscow, ul. Butyrskaya, d. 77

Warranty Period: 2 years

Address of authorized organization for claims: indicated on the warranty card