HPM Wireless Door Chime

Introduction

HPM's door chimes provide an easy and convenient solution for letting you know when you have someone calling at your door. They are "Neighbour friendly", meaning false triggering or interference is prevented. Each door chime and bell press pair is factory preset to communicate on one of over 19,000 unique channels.

Please read all instructions carefully before installation and use.

Specifications

This Chime and Bell Press are a factory set pair and are not interchangeable with other units from HPM's Cat. D641 series of door chimes.

Features

• Operating range up to 50m
• 32 melodies for selection
• Weather resistant bell press
• Flashing light

Typical Applications

• Visitor alert
• Panic button
• Pager

Box Contents

• Bell Press
• Door Chime receiver
• 1 x 3 V battery
• Mounting screws and wall plugs
• Double-sided tape

8. Important Notes Before First Time Use

1. Do not use rechargeable batteries; do not mix old and new batteries or different types. Alkaline batteries are recommended in the receiver for a longer operating life.
2. The operation and range of your wireless door chime depends on location, temperature, and battery condition.
3. Do not expose the chime unit to rain or immerse either unit in water.
4. Avoid locations where the Bell Press Transmitter is exposed to direct summer sunlight.
5. Do not leave exhausted batteries in Door Chime Receiver or Bell Press Transmitter.
6. Clean only with a damp cloth and mild detergent. Do not use solvents.

9. Maintenance

1. Keep the Door Chime dry. If the Door Chime gets wet, wipe it dry immediately. Liquids might contain minerals that can corrode electronic circuits.
2. Use and store the Door Chime only in normal temperature environments. Temperature extremes can shorten the life of electronic devices, damage batteries, and distort or melt plastic parts.
3. Handle the Door Chime gently and carefully. Dropping it can damage the circuit boards and can cause the Door Chime to work improperly.
4. Keep the Door Chime away from dust or dirt, which can cause premature wear of parts.
5. Wipe the Door Chime with a damp cloth occasionally to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the chime.
6. Use only fresh batteries of the recommended size and type. Always remove old or weak batteries. They can leak chemicals that can destroy electronic circuits.
7. Modifying or tampering with the Door Chime's internal components can cause a malfunction and might invalidate its warranty.

10. Warning

Important Safety Information:

1. Dispose of used button/coin batteries immediately by placing sticky tape around both sides of the battery and dispose of it immediately in an outside bin, out of reach of children, or recycle safely.
2. If you suspect a child has swallowed or inserted a button battery, call the 24 Hour Poisons Information Centre on 131126 for expert advice.

⚠️ WARNING

THIS PRODUCT CONTAINS A COIN BATTERY

If swallowed, a lithium coin battery can cause severe or fatal injuries within 2 hours. Keep batteries out of reach of children. If you think batteries may have been swallowed or placed inside any part of the body, seek medical attention immediately.

Warranty

Legrand warrants this product for a period of 3 years from the date of purchase.

These goods come with guarantees that cannot be excluded under the Australian and New Zealand Consumer Laws. You are entitled to a replacement or a refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

See the Warranty card enclosed with this product for further details.

Customer Service

For all Customer Service and Technical Support please call Monday to Friday during business hours.

Legrand Australia: 1300 369 777, www.hpm.com.au

Legrand New Zealand: 0800 476 009, www.hpm.co.nz

ABN: 31 000 102 661

3. Before Installation

1. Test the location of both units to ensure satisfactory operation before permanently fixing either unit in place.
2. Do not mount the Bell Press transmitter on metal or near a metal door frame, security door, or in close proximity to any metal outdoor furniture. The range of the unit may be substantially reduced.

4. Installation

Door Chime Receiver

1. Depress tab on Door Chime Receiver to remove back cover plate.
2. Insert 2 x 'AA' batteries ensuring that the coil springs contact the negative (-) end of each battery.

The Door Chime Receiver is portable and can be placed anywhere in your house or you can carry it with you using the belt clip at the back of the chime unit. It can also be fixed to a wall temporarily using the mounting screws and wall plugs provided.

The Door Chime Receiver has one slotted hang hole on the back. This hole will enable the Door Chime Receiver to be hooked onto a screw and easily removed or relocated to another room.

Bell Press Transmitter

1. If using for the first time, pull out the plastic film to activate the battery.
2. Press the Push Button to ensure that the Red LED indicator lamp lights, indicating that the battery is in working order.
3. With the help of a screwdriver, depress the clip before pulling the cover out (refer to Figure 2 description). Fix the unit to your front door or a position close by using the double-sided tape or mounting screws provided. If using screws provided, you will need to remove the back cover and fix it to the wall, then reattach the bell press to the back cover.

Note: Try different locations in your home before fixing your products in place. Both units should be more than 1 metre from the floor. Move Door Chime Receiver closer to Bell Press Transmitter to improve operation.

Warning: Wall plugs and fixing screws are provided with this kit, but may not be suitable for all installations. Ensure you use a method of fixing appropriate to your mounting surface.

5. Door Chime Operation

Press the button on the Bell Press Transmitter. The Door Chime will sound and the indicator light on the chime unit will flash.

6. Operating Instructions

Tone Selection:

The tone selector is located in the Bell Press Transmitter. To change tone, simply remove the name plate on the Bell Press and press and hold the black selector until the desired chime is reached, then release the selector.

Diagram Descriptions

Figure 1: Bell Press Transmitter

A diagram showing the Bell Press transmitter, highlighting the push button, the red LED indicator lamp, mounting holes, and the back cover which houses the coin battery.

Figure 2: Bell Press Transmitter Installation

An illustration demonstrating how to remove the back cover of the Bell Press transmitter using a screwdriver to depress a clip, and showing the mounting holes on the back cover.

Figure 3: Tone Selection

A visual representation of the Bell Press transmitter, indicating the location of the push button and a separate button labeled "Selecting Sound Button" for tone selection.

7. Troubleshooting