Ruckus ECX03431T1 1/10 2WD ELECTRIC MONSTER TRUCK Instruction Manual

Instruction Manual for Ruckus models including: ECX03431T1, ECX03431T2, ECX03433T1, ECX03433T2, ECX03433T3, 2WD ELECTRIC MONSTER TRUCK, ELECTRIC MONSTER TRUCK, MONSTER TRUCK

ECX03431-Manual-EN

1/10 Ruckus 2WD Monster Truck Brushed RTR - RC Car World (Hobby Shop Tracks)

1/10 2WD ELECTRIC MONSTER TRUCK 1/10 2WD ELECTRIC SHORT COURSE TRUCK

File Info : application/pdf, 18 Pages, 12.72MB

ECX03431-Manual-EN

Battery and Charger Not Included

1/10 2WD ELECTRIC MONSTER TRUCK 1/10 2WD ELECTRIC SHORT COURSE TRUCK

ECX03431T1 | ECX03431T2 ECX03433T1 | ECX03433T2 | ECX03433T3
INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D'UTILISATION MANUALE DI ISTRUZIONI

Congratulations on your purchase of the ECX® Ruckus® Monster Truck or TormentTM Short Course Truck. This 1/10-scale model introduces you to the sport of RC driving.
Herzlichen Glückwunsch zum Kauf des ECX Ruckus® Monster Truck oder TormentTM Short Course Truck. Dieses 1/10 Scale Model öffnet Ihnen die Welt des RC Car Sports.
Nous vous félicitons pour l'achat de l'ECX Ruckus® Monster Truck ou TormentTM Short Course Truck ou. Ce modèle 1/10 vous initie à la conduite RC.
Congratulazioni per l'acquisto di questo Ruckus® Monster Truck o TormentTM Short Course Truck. Questa vettura in scala 1/10 vi introdurrà nel mondo dei modelli RC.

NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury. CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury. NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.

Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or property of others.
This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.
· Never operate your model with low transmitter batteries. · Always operate your model in open spaces away from full-size vehicles,
traffic and people. · Never operate the model in the street or in populated areas for any
reason. · Carefully follow the directions and warnings for this and any optional
support equipment (chargers, rechargeable battery packs, etc.) you use.

· Keep all chemicals, small parts and anything electrical out of the reach of children.
· Never lick or place any portion of the model in your mouth as it could cause serious injury or even death.
· Exercise caution when using tools and sharp instruments. · Take care during maintenance as some parts may have sharp edges. · Immediately after using your model, do NOT touch equipment such as the
motor, electronic speed control and battery, because they generate high
temperatures. You may burn yourself seriously touching them.
· Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or serious injury.
· Always turn on your transmitter before you turn on the receiver in the car. Always turn off the receiver before turning your transmitter off.
· Keep the wheels of the model off the ground when checking the operation of the radio equipment.

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many "wet conditions," including puddles, creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine. The various electronic components used in the vehicle, such as the Electronic Speed Control (ESC) and servo(s) are waterproof, however, most of the mechanical components are water-resistant and should not be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is not performed after running in wet conditions. To maximize the long-term performance of your vehicle and to keep the warranty intact, the procedures described in the "Wet Conditions Maintenance" section below must be performed regularly if you choose to run in wet conditions. If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those conditions.
CAUTION: Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty.

General Precautions
· Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle.
· Not all batteries can be used in wet conditions. Consult the battery manufacturer before use. Do not use Li-Po batteries in wet conditions.
· The included transmitter is not waterproof or water-resistant. If using a different transmitter than the one included, consult your transmitter's manual or the manufacturer before operation.
· Never operate your transmitter or vehicle where lightning may be present. · Do not operate your vehicle where it could come in contact with salt
water (ocean water or water on salt-covered roads), contaminated or polluted water. Salt water is very conductive and highly corrosive, so use caution. · Even minimal water contact can reduce the life of your motor if it has not been certified as water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle until the water is mostly removed from the motor. Running a wet motor at high speeds may rapidly damage the motor. · Driving in wet conditions can reduce the life of the motor. The additional resistance of operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or any wet conditions that will increase the load on the motor for an extended period of time.

RUCKUS® | TORMENTTM

Wet Conditions Maintenance · Remove the battery pack(s) and dry the contacts. If you have an air
compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing. · Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
· Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners.

EN
· Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light oil or lubricant. Do not spray the motor.
· Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.
· Increase the frequency of disassembly, inspection and lubrication of the following: · Front and rear axle hub assembly bearings. · All transmission cases, gears and differentials. · Motor--clean with an aerosol motor cleaner and re-oil the bushings with lightweight motor oil.

Transmitter Frequency Power Output (EIRP) Battery
Servo Power Supply Output Torque Operating Speed Size

SPECIFICATIONS

2.4GHz 10 dBm AA x 4
4.8V~6V 41.66 oz (3 kg-cm) 0.23sec/60 degrees of travel 55.6 x 18 x 30mm

Electronic Speed Control (ESC)

Input Voltage

23S LiPo; 59 cell NiMH/NiCd

Electric Capacity

Forward 60A/360A

BEC Voltage

Size

35.6mm x 34mm x 18mm

Weight

1.41 oz (40 g)

BOX CONTENTS

2.4GHZ DIGITAL RADIO SYSTEM

· ECX® Ruckus® Monster Truck or TormentTM Short Course Truck · SpektrumTM STX2® 2-CH Transmitter (SPMSTX200) · AA (4) Batteries · Dynamite® 15T Brushed Motor (DYN1172) · Dynamite® 60A WP Brushed ESC (DYNS2210) · SpektrumTM SRX200 2-CH Receiver (SPMSRX200)

TABLE OF CONTENTS

Quick Start....................................................................................................4 Vehicle Preparations ....................................................................................4
Installing the Battery.................................................................................4 Transmitter Controls..................................................................................5 Installing Transmitter Batteries ................................................................5 Binding ......................................................................................................6 Changing the Throttle Limit ......................................................................6 Getting Started..........................................................................................6 Operation......................................................................................................7 When You Are Finished................................................................................7 Motor Care ...................................................................................................7 Maintenance ................................................................................................8 Setting the Gear Mesh..............................................................................8 Electronic Speed Control (ESC) .................................................................8

Electrical Layout........................................................................................8 Shock Cleaning..........................................................................................9 Fasteners ......................................................................................................9 Troubleshooting Guide ...............................................................................10 Limited Warranty .......................................................................................11 Warranty and Service Contact Information ...............................................12 FCC Information..........................................................................................12 IC Information.............................................................................................12 EU Compliance Statement .........................................................................12 Instructions for Disposal of WEEE by Users in the European Union.........12 Ruckus Parts Diagram ......................................................................... 4647 Torment Parts Diagram ....................................................................... 4849 Replacement Parts .............................................................................. 5051 Optional Parts.............................................................................................51

RUCKUS® | TORMENTTM

QUICK START
Please read the entire manual to gain a full understanding of the vehicle, fine-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual.
2. Charge a battery for the vehicle. Refer to the included charging warnings and instructions for battery charging information.
3. Install the AA batteries in the transmitter. Only use alkaline or rechargeable batteries.
4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to initialize. Always power the transmitter ON before the vehicle and power it OFF after the vehicle has been powered OFF.
6. Check the steering and throttle control directions. Verify that the servos are moving in the correct direction.
7. Drive your vehicle.
8. Perform any necessary maintenance.

VEHICLE PREPARATIONS

INSTALLING THE BATTERY

1. Turn the battery clips (A) clockwise to remove the battery strap (B). 2. Install a fully charged battery. 3. Install the battery strap. 4. Turn the battery clips counterclockwise to secure the battery strap.

Place foam blocks (ECX2015) in front of the battery so the weight of

the battery increases rear traction or in back of the battery to increase

steering response.

CAUTION: Connecting the battery to the ESC with reversed polarity will cause damage to the ESC, the battery or both. Damage caused by incorrectly connecting the battery is not covered under warranty.

RUCKUS® | TORMENTTM

TRANSMITTER CONTROLS

6 5
43

9
10 12

1. Steering Wheel Controls direction (left/right) of the model

2. Throttle Trigger Controls speed and direction (forward/brake/reverse)

of the model

3. ON/OFF Switch Turns the power ON/OFF for the transmitter

4. Throttle Limiting Switch Adjusts the throttle limit from 50%, 75%,

and 100%

5. TH Rate Adjusts the end point of the throttle

6. TH Trim Adjusts the throttle neutral point

7. TH REV Reverses the function of the speed control when pulled back

or pushed forward

8. ST REV Reverses the function of the steering when the wheel is turned

left or right

9. ST Trim Adjusts the steering center point

10. ST Rate Adjusts the end point of the steering

11. Antenna Transmits the signal to the model

12. Indicator Lights

· Solid red lights--indicates radio connectivity and adequate

battery power

· Flashing red lights--indicates the battery voltage is critically

low. Replace batteries

INSTALLING TRANSMITTER BATTERIES

2
2.4GHZ DIGITAL RADIO SYSTEM

This transmitter requires 4 AA batteries.
1. Remove the battery cover from the transmitter. 2. Install the batteries as shown. 3. Install the battery cover.
CAUTION: Never remove the transmitter batteries while the model is powered ON. Loss of model control, damage, or injury may occur.
CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to national regulations.

RUCKUS® | TORMENTTM

EN
BINDING
Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. The STX2® transmitter and SPMSRX200 receiver are bound at the factory. If you need to rebind, follow the instructions below.

You must rebind when: · Different failsafe positions are desired e.g., when throttle or steering reversing has been changed. · Binding the receiver to a different transmitter.
CHANGING THE THROTTLE LIMIT
Throttle Limit Switch

1. With the vehicle on a flat, level surface, insert the Bind Plug in the BIND port on the receiver.
2. Connect a fully charged battery pack to the ESC. 3. Power on the ESC. The red LED flashes, indicating the receiver
is in bind mode. 4. Center the ST TRIM and TH TRIM dials on the transmitter. 5. Turn the steering wheel to Full Right. Power the transmitter on
while holding the steering wheel to the Right. 6. Release the steering wheel when the receiver LED stops flashing. 7. Remove the Bind Plug, then power off the receiver to save the
settings. 8. Power off the transmitter. 9. Remove the bind plug and store it in a convenient place.

Beginner Mode Throttle Limiting Switch: 50%
· Best for learning the basic functions of left, right, stop, brake and reverse · For use in smaller areas · Longest battery life
Best Overall Performance (Default) Throttle Limiting Switch: 75%
· Great top speed and acceleration · Easier to accelerate in desired direction, especially on loose surfaces
when compared to Maximum Speed setup
· Run time is greatly increased over Maximum Speed setup with minimal impact to top speed
Maximum Speed Throttle Limiting Switch: 100%
· More capable of popping and holding wheelies · Higher top speeds and maximum acceleration

GETTING STARTED
1. Power on the transmitter.

2. Power on the ESC.

3. Perform a test of the transmitter's control of the vehicle with the vehicle's wheels off the ground.

4. Start driving slowly, and, if the vehicle does not go straight, adjust the steering trim dial on the transmitter.

2.4GHZ DIGITAL RADIO SYSTEM
6

IMPORTANT: Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Properly seating the motor brushes will increase the life and performance of the motor.
RUCKUS® | TORMENTTM

OPERATION

· ALWAYS turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your
transmitter off.

· ALWAYS operate your vehicle in a wide open area. Operating the vehicle in a small space or indoors can cause overheating at low speeds. Operating at low speed increases heat in the electronic speed control (ESC). Overheating can damage the vehicle and failure may result.

1. Power off the ESC.

WHEN YOU ARE FINISHED
2. Disconnect the battery.

3. Power off the transmitter.

4. Remove the battery from the vehicle.

5. Recharge the battery.

MOTOR CARE

· Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Failing to do so can greatly reduce motor performance and functional life.
· Prolong motor life by preventing overheating conditions. Undue motor wear results from frequent turns, stops and starts,
pushing objects, driving in deep water and tall grass, and driving

continuously up hill. Allow the motor to cool completely before running the vehicle. · Over-temperature protection is installed on the ESC to prevent circuit damage, but cannot protect the motor from driving against
heavy resistance.

RUCKUS® | TORMENTTM

MAINTENANCE

SETTING THE GEAR MESH
The gear mesh has already been set at the factory. Setting the gear mesh is only necessary when changing motors or gears.
You must remove the vehicle's gear cover (A) to make this adjustment.
Proper gear mesh (how the gear teeth meet) is important to the performance of the vehicle. When the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If the mesh is too tight, speed could be limited and the motor and ESC will overheat. Set the gear mesh by following these simple steps:
1. Loosen the 2 motor screws (B). 2. Put a small piece of paper (C) between the pinion and spur gears. 3. Push the gears together while tightening the motor screws.

B C
A
4. Rotate the gears to remove the paper. The gearing should move a small amount.
5. Reinstall the gear cover.

ELECTRONIC SPEED CONTROL (ESC)
Programming: The ESC comes with one jumper pre-installed: BATT: Li-Po configuration.
The throttle setting without the jumper indicates Throttle/Brake/Reverse. Always use this setting for this vehicle.
To change the battery type to Ni-MH, disconnect the jumper from the default port and connect it to the Ni-MH port. If the jumper is removed from the BATT port, the default setting is Li-Po mode. Power off the ESC, then power it back on.
If the jumpers are lost or not installed, the ESC will default to REV: ON and BATT: Li-Po.
NOTICE: Only use the Ni-MH port when using Ni-MH batteries. Using the Ni-MH port with a Li-Po battery can cause serious damage to the battery and is unsafe.

Operation Start up Low Voltage Cut-Off Low Voltage at Start Up

Tone One short tone, followed by one long tone. When low voltage cuttoff is reached, the vehicle will slow and emit a continuous tone. When a low battery is plugged in and powered on, the vehicle will emit two low tones and power off.

ELECTRICAL LAYOUT

Part #

Description

A DYN1172 Motor

Needed to complete

Battery 7.4V

C SPMS603* Waterproof Steering Servo

D SPMSRX200 Receiver

E DYNS2210

Waterproof Electronic Speed Control (ESC)

Channel 1

Channel 2

*OEM part only. Replacement, please use part SPMSS6170.

For correct operation, Channels 1 and 2 must be used as shown in the wiring diagram. The motor can be disconnected from the ESC at the connectors in the wiring.

EC3

G F

RUCKUS® | TORMENTTM

SHOCK CLEANING
Oil-filled shocks require regular maintenance because oil breaks down and/or gets dirty. Perform this maintenance every 35 hours of use, depending on useage conditions.
· Remove the shock from the vehicle. · Remove the cap from the shock body and dispose of fluid. · Disassemble the shock. Clean thoroughly with a plastic- and
electronic-safe degreaser (DYNE50001). Dry parts before assembly. · Re-assemble the shock and refill the shock body with silicone fluid
(30 weight recommended). · Slowly move the shaft and piston up and down to remove air bubbles. · Move the piston to the midway point of the body and install the cap. · Wipe off any overflowing fluid. · When properly filled, the piston should rebound about 3/8 in (9.5mm)
after being pushed in fully. · Re-install the shock on the vehicle.
RIDE HEIGHT ADJUSTMENT
Ride height is an adjustment that affects the way the vehicle jumps, turns and goes over bumps. Drop one end of the vehicle from approximately 6 inches (152 mm) in height onto a flat surface. When dropping the front of the vehicle, after the vehicle settles, make sure the front arms are equal and parallel to the flat surface. Do the same with the rear to make sure both arms are parallel with the flat surface.
Lowering the front ride height increases steering, but decreases traction. Lowering the rear ride height increases traction, but decreases steering.

REAR SHOCK
ECX1037
ECX1043 ECX1057
ECX1038 ECX1036
ECX1038 ECX1043
ECX1037
ECX1040

FRONT SHOCK
ECX1037

ECX1043 ECX1037

ECX1057

ECX1038 ECX1036
ECX1038
ECX1043 ECX1037

ECX1039

ECX1042

ECX1041 ECX1038

ECX1037

Part # ECX1036 ECX1037 ECX1038 ECX1039 ECX1040 ECX1041 ECX1042 ECX1043

Description Shock Body Set Shock Caps, Pistons Shock Parts Set Front Shock Shaft (2) Rear Shock Shaft (2) Front Shock Springs (2) Rear Shock Springs (2) Shock O-Ring Set

ECX1038

FASTENERS

No. Description

No.

TAPPING BINDER HEAD M3x10mm
TAPPING BINDER HEAD M3x12mm
TAPPING BINDER HEAD M3x16mm
TAPPING BINDER HEAD M3x18mm
TAPPING FLAT HEAD M3x10mm
TAPPING FLAT HEAD M3x12mm
TAPPING FLAT HEAD M3x15mm

Description

No.

TAPPING FLAT HEAD M2x16mm
BINDER HEAD M3x8mm
BINDER HEAD M3x12mm
BINDER HEAD M3x20mm
BINDER HEAD M3x25mm
BUTTON HEX M2.5x4mm
BUTTON HEX M2.5x8mm

Description

No.

STEP SCREW M3x0.5x7.4mm

STEP SCREW M3x0.5x13.4mm

STEP SCREW M3x0.5x10.5mm

SETSCREW M3x3mm

SETSCREW M3x12mm
SET SHAFT SCREW M3x13mm

Description WASHER 5x7x0.5mm
WASHER 3x8x0.5mm
WASHER 2x7x0.5mm FLANGED LOCK NUT M4
LOCK NUT M3
E-CLIP E2.5
LOCK WASHER

RUCKUS® | TORMENTTM

TROUBLESHOOTING GUIDE

Problem Short run time Sluggish action Controls reversed Motor/ESC overheat
Does not operate
Poor range
The system will not connect

Possible Cause Battery damaged/not charged Motor dirty Motor dirty Bind in drivetrain Vehicle battery is not charged ST. REV or TH. REV Over-geared for the driving environment Transmitter batteries low Transmitter powered off ESC powered off Vehicle battery is not charged Dual-rate (D/R) steering and/or throttle knobs on transmitter are turned counterclockwise Transmitter batteries low Receiver antenna damaged Transmitter and receiver too near each other Transmitter and receiver too near large metal objects (vehicles, etc.)
Throttle trim out of center on transmitter

The receiver goes into failsafe mode a short distance away from the transmitter
The receiver quits responding during operation
Receiver and transmitter are not bound Vehicle moves forward or backward without input from user

Receiver accidentally put in bind mode so receiver is no longer bound
Check the receiver antenna to be sure it is not cut or damaged
Low battery voltage Loose or damaged wires or connectors between battery and receiver Transmitter accidentally put in bind mode, ending bind to receiver
Throttle trim on transmitter not centered

Car does not drive straight

Steering trim on transmitter not centered

No steering or lack of steering
No throttle or lack of throttle Clicking noise in transmission area

Steering dual-rate (D/R) on transmitter not adjusted correctly Servo failed Throttle dual-rate (D/R) on transmitter not adjusted correctly ESC failed Motor failed Dirt or rocks in spur gear Motor moved away from spur gear

Solution Check/change battery Check/clean Check/clean Clean/adjust Replace/recharge Change switch position Install smaller pinion on the motor Replace/recharge Power on Power on Replace/recharge Adjust dual-rate (D/R) steering or throttle knobs clockwise to desired setting Replace/recharge Check/repair/replace Move transmitter 3.39.8ft (13m) from receiver
Move away from large metal objects (vehicles, etc.)
Set throttle trim on transmitter to zero. Turn off and on transmitter and vehicle
Rebind transmitter and receiver
Make sure the antenna is in the antenna tube Contact Horizon Product Support
Completely recharge battery Do a check of the wires and connection between battery and receiver. Repair or replace wires and/or connectors
Bind transmitter to receiver
Adjust throttle trim on transmitter to neutral point
Adjust steering trim on transmitter so the vehicle drives straight Adjust steering dual-rate (D/R) knob on transmitter clockwise to desired steering throw Contact Horizon Product Support Adjust throttle dual-rate (D/R) knob on transmitter clockwise to desired steering throw Contact Horizon Product Support Contact Horizon Product Support Remove gear cover and inspect. If necessary, replace gear Reset gear mesh

RUCKUS® | TORMENTTM

LIMITED WARRANTY

What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the "Product") will be free from defects in materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER'S INTENDED USE.
Purchaser's Remedy
Horizon's sole obligation and purchaser's sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event

that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www. horizonhobby.com/content/service-center_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a Li-Po battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier's checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon's Terms and Conditions found on our website http://www. horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender's choice and at the sender's expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.
10/15

RUCKUS® | TORMENTTM

WARRANTY AND SERVICE CONTACT INFORMATION

Country of Purchase
United States of America
European Union

Horizon Hobby
Horizon Service Center (Repairs and Repair Requests)
Horizon Product Support (Product Technical Assistance)
Sales
Horizon Technischer Service Sales: Horizon Hobby GmbH

Contact Information
servicecenter.horizonhobby.com/ RequestForm/
productsupport@horizonhobby.com 877-504-0233
websales@horizonhobby.com 800-338-4639
service@horizonhobby.eu +49 (0) 4121 2655 100

Address
1608 Interstate Drive Champaign, Illinois, 61822 USA
Hanskampring 9 D 22885 Barsbüttel, Germany

*For the most up-to-date customer service contact information, please visit: www.horizonhobby.com/content/service-center-render-service-center

FCC INFORMATION

FCC ID: 2AI3D-SS0001 This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Antenna Separation Distance When operating your Spektrum transmitter, please be sure to maintain a separation distance of at least 5 cm between your body (excluding fingers, hands, wrists, ankles and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.
The following illustrations show the approximate 5 cm RF exposure area and typical hand placement when operating your Spektrum transmitter.

NOTICE: Modifications to this product will void the user's authority to operate this equipment.

IC INFORMATION

IC ID: 21682-SSTC9202 This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED and EMC directives.
A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.

Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user's responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.

RUCKUS® | TORMENTTM

RUCKUS PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI

The slipper clutch can be adjusted using this locknut (ECX1060). Fully tighten the locknut, then loosen the nut two full turns.

Die Rutschkupplung kann durch

diese Stopmutter eingestellt

werden (ECX1060). Ziehen Sie die

Mutter an und drehen Sie dann

volle zwei Umdrehungen zurück.

M3X3

M2.5X8 32

41a

M2.5X4

22 34 34 34

M2.5X8

42 34 34

Il est possible d'ajuster le sliper par action sur cet écrou de blocage (ECX1060). Veillez à serrer l'écrou de blocage à fond. Ensuite, devissez l'écrou de deux tours complets.

33 48 48

35 15 33 15 40 33
33 35

36 M2X16

La frizione può essere regolata con questo dado autobloccante (ECX1060). Prima avvitate completamente il dado, poi svitatelo 2 giri.

36 25

39 38 35 33

35 33 35 33

M2X16

43 44 12

15
M3X18 36
M3X12 25 M3X12

M3X15

M3X12

M3X15 46

M3X10

M3X12

47 M3X12

M3X12

M3X18

47 M3X12

39 50

M3X20 31

M3X10

19 29

M3x15

20 3
13

M3X12

M3x12

When installing the wheel, make sure the drive hex is aligned with the drive pin. When the drive hex is removed, the drive pin can fall out of the axle. Bitte achten Sie bei der Radmontage darauf, dass die Radachse im Radmitnehmer sitzt und dass der der Querstift nicht heraus fällt. Lors de l'installation de la roue, assurez-vous que l'hexagone de roue est aligné avec la goupille d'entraînement. En cas de démontage de l'hexagone, la goupille peut sortir de l'axe et tomber. Quando montate le ruote, accertatevi che il trascinatore esagonale sia allineato con la spina del mozzo ruota. Quando togliete il trascinatore esagonale la spina può sfilarsi dal mozzo.

29 19
23
15

27
M3X12 31
26b

26a 26b

14a

13 22

RUCKUS® | TORMENTTM

TORMENT PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI

M3X10

11 M3X10

M3X10

M3X12

M3X18

51 M3X12 1

M3X12

M3X25

M3X10

51 M3X18

45 49
M3X15

M3X12 44

2 4

M3X12

M3X10

13 46

M3X10

2 19

M3X15

19 20 M3X25
M3X15
31

29 23
8

M3X8 19 M3X12
M3X10

31 M3X12

M3X12
8 7
18 23 21
15 15 13

14b 22

RUCKUS® | TORMENTTM

TORMENT PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI

The slipper clutch can be adjusted using this locknut (ECX1060). Fully tighten the locknut, then loosen the nut two full turns. Die Rutschkupplung kann durch diese Stopmutter eingestellt werden (ECX1060). Ziehen Sie die Mutter an und drehen Sie dann volle zwei Umdrehungen zurück. Il est possible d'ajuster le sliper par action sur cet écrou de blocage (ECX1060). Veillez à serrer l'écrou de blocage à fond. Ensuite, devissez l'écrou de deux tours complets. La frizione può essere regolata con questo dado autobloccante (ECX1060). Prima avvitate completamente il dado, poi svitatelo 2 giri.

M3X3

32 M2.5X8 32

41b

M2.5X4

22 34 34 32

42
34 34 15

M2.5X8

33 48 48 35 15 33 15 40 33

M2X16 33

M3X18 36

36 25

39 38 35 33

33 35

33 35 33

M2X16

M3X12 25 M3X12

M3X15

43 44

M3X15

M3X12

M3X12 M3X18

M3X10 25 47

M3X10 M3X12 46

M3X12

50 M3X12

M3X10

3 M3X20

M3X12 49 39

M3X10

13
3 13

M3X15 20

26a

M3X12

26b

M3X12

14b

13 22

RUCKUS® | TORMENTTM

Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio

Part # 1 ECX2008 2 ECX1028

Description Main Chassis Servo Saver Set

3 ECX2011 Cover and Rear Mount Set

4 ECX1050 Setscrew M3 x 12 (4)

5 ECX1053 Foam Block

6 ECX1098 Motor Screw/Washer Set

7 ECX1058 Ball Stud (6)

8 ECX1065 Shoulder Screw Set (8)

9 SPMSRX200 2-Ch Receiver

11 ECX231003 Battery Strap, ESC Plate

12 ECX231002 Rear Bumper Set

13 ECX2006 Suspension Arm Mount Set

14a ECX43008

FR/RR Wheel/Tire, Premount, Black (2)

14b ECX4003

FR/RR Wheel/Tire, Premount, Black (2)

15 ECX1015 Ball Bearing 5 x 10 x 4mm (8)

16 ECX1018 Front Suspension Arm Set

17 ECX1020 Shock Tower Set

18 ECX1035 Front Axle (2)

19 ECX1044 Hinge Pin Set

20 ECX1046 Camber, Toe Link Set

21 ECX1049 22 ECX1060
23 ECX234000
24 ECX1019 25 ECX1021
26a ECX232000

Wheel Pins (4)
M4 Locknut (4)
Caster Block, Steer Block, RR Hub (2)
Rear Suspension Arm Set
Transmission Case Set
Long Driveshaft Set, Complete HD (2)

26b ECX232002 Long Driveshaft, Plastic Only HD (2)

27 ECX232005 28 ECX232001 29 ECX1045
30 DYNS2210

Driveshaft Pivot Ball (4)
Rear Axle (2)
Button Head Screw 2.5 x 4mm (8)
WP 60A FWD/REV Brushed ESC (ESC)

31 ECX1037 Shock Caps, Pistons, Pivot Ball Set

32 ECX1027 Gear Cover

33 ECX1022 Transmission Gear Set

34 ECX1024 Slipper Clutch Plates, Pads, Spring

35 ECX1025 Transmission Idler Shaft, Drive Pins

36 ECX1026 37 ECX1052 38 ECX1055 39 ECX1059 40 ECX1076 41a ECX232029 41b ECX1073 42 DYN1172 43 ECX1048 44 ECX2010

Transmission Drive Shaft (2) Washer/Shim Set Bearings 10 x 15 x 4mm (2) M3 Locknut (4) Spur Gear 48P, 87T 17T, 48P Pinion Gear 19T, 48P Pinion Gear Dynamite 15T 540 Brushed Motor Body Clip (8) Body Post Set

Beschreibung Chassis Servo Saver Set
Abdeckung und hinterer Halter Set
Schrauben Set M3 x 12 (4) Schaum Block Motor Screw/Washer Set Kugelkopf (6) Passschrauben Set (8) 2 Kanal Empfänger Akkugurt, ESC-Platte Hintere Stossstange Querlenker Set hinten Vorder-/Hinterreifen/-rad, vormontiert, Schwarz (2) Vorder-/Hinterreifen/-rad, vormontiert, Schwarz (2) Kugellager 5 x 10 x 4 mm (8) Querlenker Set vorne Dämpferbrücke Radachse vorne (2) Querlenkerbolzen Set
Spur- Sturzstangenset
Radmitnehmerstifte (4) M4 Stopmutter (4) Radblock, Steuerblock, Hinterradnabe (2) Querlenker Set hinten Getriebegehäuse
Lange Antriebswelle, HD (2)
Lange Antriebswelle, nur Kunststoff HD (2) Antriebswellen Kugelkopf (4) Wellenmitnehmer hinten (2) Rundkopfschraube 2,5 x 4 mm (8)
Elektrischer Fahrtenregler (ESC)
Stoßkappe, Kolben, Schwenkkugel-Set
Gear Cover
Getriebe
Rutschkupplung Teilesatz
Hauptgetriebewelle Set
Getreibeausgangswelle (2) Unterlegscheiben/Shim Set Lager 10 x 15 x 4mm (2) M3 Stopmutter (4) Hauptzahnrad 48P, 87T 17T, 48P Pinion Gear 19T, 48P Pinion Gear Dynamite 15T 540 Bürstenmotor Body Clip (8) Body Post Set

Description Châssis principal Sauve servo
Capot et fixations arrières
Jeu de vis M3 x 12 (4) Bloc de mousse Set vis/rondelles moteur Rondelle (6) Jeu de vis épaulées (8) Récepteur 2 voies Sangle de batterie, plaque du variateur ESC Pare-choc arrière Jeu de renfort de suspension Volant/Pneu avant/arrière, prémonté, noir (2) Volant/Pneu avant/arrière, prémonté, noir (2) Roulement à billes 5 x 10 x 4 mm (8) Jeu de bras de suspension avant Jeu de support d'amortisseur Axe de roue avant (2) Jeu d'axes de suspension Jeu de biellettes de carrossage et de pincement Goupilles d'entraînement (4) Ecrous auto-freinés M4 (4) Blocs de roulettes, Bloc de direction, Corps de fusées arrière (2) Jeu de bras de suspension arrière Ensemble carter de transmission

Descrizione Telaio principale Set salvaservo Copertura e set di montaggio posteriore Grani M3 x 12 (4) Spugna distanziale batteria Viti per il motore/set di rondelle Sfere uniball (6) Set viti a doppio stadio (8) Ricevitore Fascetta batteria, piastra ESC Set paraurti posteriore Supporti braccetti sosp. Ruota/pneumatico ant/post, premontato, nero (2) Ruota/pneumatico ant/post, premontato, nero (2) Cuscinetto a sfera, 5 x 10 x 4 mm (8) Braccetti delle sospensioni anteriori Supporto ammortizzatori posteriori Mozzi ruota anteriori (2) Set perni sospensioni
Set tiranteria Camber e convergenza
Spine trascinatori ruote (4) Dadi autobloccanti M4 (4) Blocco ruota anteriore, blocco sterzo, mozzo posteriore (2) Braccetti delle sospensioni posteriori Set scatola trasmissione

Long arbre de transmission, HD (2)

Albero di trasmissione lungo, HD (2)

Long arbre de transmission, uniquement Albero di trasmissione lungo, solo

en plastique ultra-résistant (2)

plastica HD (2)

Croisillon de cardan (4)

Attacco a sfera semiasse (4)

Axe de roue arriere

Attacco a sfera semiasse (4)

Vis à tête bombée, 2,5 x 4 mm (8)

Vite a testa tonda, 2,5 x 4 mm (8)

Variateur 60A marche av/arr étanche pour Regolatore elettronico di velocità (ESC)

moteur à charbon

Ensemble de Capuchons d'amortisseurs, Set articolazione a rotula, pistoni, tappi

Pistons, Rotule

ammortizzatore

Carter de Réducteur

Copertura per ingranaggi

Couronne et pignons intermédiaires, corps et pignons de différentiel

set ingranaggi trasmissione

Garnitures, plateaux et ressort de slipper

Piattelli frizione, disco, molla

Arbre secondaire de transmission avec goupilles d'entraînement

Alberino intermedio con spina

Axe de sortie de différentiel (2)

Mozzi Differenziale (2)

Jeu de rondelles/Shim

Set rondelle/Shim

Roulements 10 x 15 x 4mm (2)

Cuscinetti 10 x 15 x 4mm (2)

Ecrou auto-freiné M3 (4)

Dadi autobloccanti M3 (4)

Couronne 48P, 87T

Corona 48P, 87T

Pignon 17T, 48P dents

Pignone a 17T, 48P denti

Pignon 19T, 48P dents

Pignone a 19T, 48P denti

Moteur Dynamite 15T 540 Brushed

Motore a spazzole Dynamite 540 15T

Clips Carrosserie (8)

Clips per carrozzeria (8)

Set Plots Carrosserie

Set di sostegni per la carrozzeria

RUCKUS® | TORMENTTM

Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio

Part # Description 45 ECX2009 Body Mount Set 46 ECX2007 Skid Plate Set 47 ECX2013 RR Bump Mount 48 ECX1023 Top Shaft/Spacer 49 ECX1033 Setscrew M3 x 10 50 ECX231001 Front Bumper Set
ECX230023 Body: 1/10 K&N Torment ECX230038 Body, Black/Yellow ECX230039 Body, Orange ECX230040 Body, Yellow/Blue ECX230041 Body, Lucas Oil SPMSTX200 STX2 2CH Transmitter

Beschreibung Aufnahme Karosseriehalter Skid Plate Set Heckstoßstangenhalterung Top Shaft/Spacer Feststellschraube M3 x 10 Vordere Stossstange Karosserie: 1/10 K&N Torment Karosserie, schwarz/gelb Karosserie, orange Karosserie, gelb/blau Karosserie, Lucas Oil STX2 2-Kanal Fernsteuerung

Description Set Montage Carrosserie Set Plaque Chassis Support de pare-chocs arrière Set de Goupilles Vis de fixation M3 x 10 Pare-choc avant Carrosserie: 1/10 K&N Torment Carrosserie, Noire/Jaune Carrosserie, Orange Carrosserie: Jaune/Bleu Carrosserie, Lucas Oil Émetteur STX2 2 voies

Descrizione Set di montaggio per la carrozzeria Set pistre di protezione Supporto bumper posteriore Set di spessori Vite di arresto M3 x 10 Set paraurti anteriore Carrozzeria: 1/10 K&N Torment Carrozzeria, nero/giallo Carrozzeria, arancione Carrozzeria, giallo/blu Carrozzeria, Lucas Oil Trasmittente STX2 2 canali

Optional Parts / Optionale Teile / Liste des options / Elenco parti opzionali

Part #
DYN1400
DYN1405
DYNG4810
DYNH1040
DYNS0600
DYNT0500 ECX1061 ECX1095 ECX1096 ECX1097 ECX330001 ECX331000 ECX331001 ECX331005 ECX331006 ECX331008 ECX332000 ECX334000 ECX334001 ECX334002 ECX9001 KXSB9501 KXSB9502 KXSB9503
KXSS0500
KXSS0501
RPM70462 RPM70582
RPM70672
RPM73292 RPM73442 RPM73492 RPM73572

Description
LiPo Charge Protection Bag,Small
LiPo Charge Protection Bag, Large
Pinion Gear Set: 17T. 18T, 19T, 20T, 21T x 48P Stainless Steel Screw Set
Tazer 1/10 3300Kv ESC/Motor Combo
Startup Tool Set Screw Set (64) Aluminum Shock Set Front: Aluminum Shock Set Rear Universal Battery Strap (1) Body, Clear: 1:10 2WD Ruckus Front Shock Tower, Aluminum Rear Shock Tower, Aluminum Servo Arm 23T, Aluminium Servo Arm 24T, Aluminium Steering w/Servo Saver, Aluminium Wheel Hex, Aluminum Rear Hubs, Aluminum Caster Block, Aluminum Steering Block, Aluminum Metal Gear Set LiPo Charge Bag14 x 6.5 x 8cm LiPo Charge Bag 18 x 8 x 5.5cm LiPo Storage and Carry Bag
1/10 4P 3000Kv ESC/Motor Combo
1/10 4P 4000Kv ESC/Motor Combo
RR A-arms (2), Black FR A-arms (2), Black
Sealed Gear Cover, Black
FR Spindle Blocks (2), Black HD Caster Blocks, Black SX-Saver Bellcrank, Black Rear Axle Carriers, Black

Beschreibung

Description

Descrizione

LiPo Ladeschutztasche, klein

Sac de protection du chargeur de batterie Li-Po, petit

Borsa di protezione per carica batterie LiPo, piccola

LiPo Ladeschutztasche, groß

Sac de protection du chargeur de batterie Li-Po, grand

Borsa di protezione per carica batterie LiPo, grande

Dynamite Ritzelset: 17/18/20/21 Zähne 48P

Set de pignons - 17T,18T, 19T, 20T, 21T 48P

Set pignoni: 17T, 18T, 19T, 20T, 21T x 48P

Dynamite Edelstahlschraubenset

Kit de visserie acier inox

Set viti in acciaio inossidabile

Tazer 1/10 3300Kv Geschwindigkeitsregler-/Motor-Kombi

Variateur ESC/Moteur combinés Tazer 1/10 3 300 Kv

Tazer 1/10 3300 Kv combo ESC/motore

Werkzeug Set

Set d'outils de démarrage

Set attrezzi start up

ECX Blechschraubenset (64 Stk)

Set de vis (64)

Set viti (64)

ECX Aluminium-Dämpferset vorne

Set d'amortisseurs avant en aluminium Set ammortizzatore ant. in allu.

ECX Aluminium-Dämpferset hinten

Set d'amortisseurs arrière en aluminium Set ammortizzatore post. in allu

ECX Electrix-Akkuhalteband: 7-Zellen-Akku Sangle universelle pour batterie

Velcro fissaggio batteria universale (1)

ECX Karosserie, unlackiert: Ruckus

1/10 2WD Ruckus - Carrosserie transparente Carrozzeria trasparente: 1:10 2WD Ruckus

ECX Aluminium-Dämpferbrücke vorne Support d'amortisseurs avant aluminium Torre ammortizzatore ant. in allu.

ECX Aluminium-Dämpferbrücke vorne Support d'amortisseurs arrière

Torre ammortizzatore post. in allu

Servoarm 23T, Aluminium

Palonnier de servo 23T, Aluminium

Squadretta servo 23T, alluminio

Servoarm 24T, Aluminium

Palonnier de servo 24T, Aluminium

Squadretta servo 24T, alluminio

Lenkung mit Servosaver, Aluminium Direction avec sauve-servo, Aluminium Sterzo con salvaservo, alluminio

ECX Aluminium Radmitnehmer

Hexagones de roue en aluminium

Esagono ruota, allu.

ECX Aluminium-Radträger hinten

Fusées arrière aluminium

Mozzi post., allu.

ECX Aluminium-Achsschenkelträger Étriers porte fusée aluminium

Caster Block, allu.

ECX Aluminium-Lenkträger

Fusées avant aluminium

Fusello dello sterzo, allu.

ECX Metallgetriebeset

Set de pignons métal

Set ingranaggio in metallo

LiPo Ladetasche 14 x 6,5 x 8 cm

SacduchargeurdebatterieLi-Po14x6,5x8cm Borsa caricabatteria LiPo 14 x 6,5 x 8 cm

LiPo Ladetasche 18 x 8 x 5,5 cm

SacduchargeurdebatterieLi-Po18x8x5,5cm Borsa caricabatteria LiPo 18 x 8 x 5,5 cm

LiPo Aufbewahrungs- und Tragetasche Sac de stockage et transport de Li-Po Custodia da trasporto LiPo

1/10 4P 3000Kv Geschwindigkeitsregler-/Motor-Kombi

Variateur ESC/Moteur combinés 1/10 4P 3 000 Kv

1/10 4P 3000 Kv combo ESC/motore

1/10 4P 4000Kv Geschwindigkeitsregler-/Motor-Kombi

Variateur ESC/Moteur combinés 1/10 4P 4 000 Kv

1/10 4P 4000 Kv combo ESC/motore

RR A-Arm (2), Schwarz

Bras de commande A arrière (2), noirs Bracci di controllo, posteriori (2), nero

FR A-Arm (2), Schwarz

Bras de commande A avant (2), noirs Bracci di controllo, anteriori (2), nero

Abgedichtete Getriebeabdeckung, Schwarz

Couvercle de l'engrenage hermétique, noir

Coperchio pignone sigillato, nero

FR Spindelblöcke (2), Schwarz

Blocs d'axe avant (2), noirs

Blocchi alberino, anteriore (2), nero

HD Radblock, Schwarz

Blocs de roulettes ultra-résistants, noirs Blocchi ruota anteriore HD, nero

SX-Saver-Umlenkhebel, Schwarz

Levier coudé SX-Saver, noir

Leva a squadra SX-Saver, nero

Hinterachsträger, Schwarz

Supports d'essieu arrière, noirs

Porta asse posteriore, nero

RUCKUS® | TORMENTTM

ECX03431T1 | ECX03431T2 ECX03433T1 | ECX03433T2 | ECX03433T3
www.ecxrc.com

© 2018 Horizon Hobby, LLC. ECX, the ECX logo, Ruckus, Torment, Dynamite, Prophet, STX2, EC3, Tazer, SpeedTreads, Reaction and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.

Updated 05/2018

58064

References

GPL Ghostscript 9.55.0 Adobe InDesign CS5.5 (7.5.3)