Welcome to PureEdge Lighting
Instruction Manual for PURE EDGE models including: 904-TXSP-UNI_02 Suspension with Power Center Feed, 904-TXSP-UNI_02, Suspension with Power Center Feed, Power Center Feed, Center Feed, Feed
File Info : application/pdf, 6 Pages, 577.03KB
DocumentDocumentDoc # 904-TXSP-UNI_02 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.PureEdgeLighting.com info@PureEdgeLighting.com © 2016 PureEdge Lighting. All Rights Reserved. Installation Instructions for Tie Stix Suspension with Power Center Feed IMPORTANT INFORMATION - This product is ETL listed. - This product is suitable for indoor locations. - This instruction shows a typical instruction. - Two additional aircraft cables are added for support when fixture lengths are 72 inches and longer. - This product must be installed by a qualified electrician and in accordance with local electrical codes. SAVE THESE INSTRUCTIONS! TXSP-_-C_-_ Section One: Install the Canopy A MOUNTING PLATE 1 1: Remove the four Phillips screws from the canopy to remove the mounting plate. NOTE: It is recommended more than one person to assist in this installation. 1 PHILLIPS B CANOPY SCREW 2: Select the appropriate knockout on the mounting plate and remove it using a flathead screwdriver or other appropriate tool. MOUNTING PLATE 2 KNOCKOUT SAFETY CABLE C 3 JUNCTION BOX ANCHOR CEILING 4 3: Align the mounting plate holes with the junction box. Mark one point on each side of the junction box onto the ceiling. NOTE: Step 4 is for drywall mounting. Omit this step if mounting directly onto a wood surface. 4: Tap the anchors onto the marked points up to the threaded portion with a hammer. Then screw in the threaded portion with a Phillips screw driver. 1 D 6 5 CEILING 5: Make sure the mounting plate is grounded in accordance with local electrical codes. 6: Feed the line voltage power wires through the mounting plate knockout. 7: Secure the mounting plate to the junction box and anchors using the provided screws and washers. WASHER 7 SCREWS LINE VOLTAGE POWER WIRES Section Two: Power the Fixture E CANOPY H 1: Determine the fixture height (H), from the bottom of the channel to the top of the canopy. 1 CHANNEL F CANOPY NOTE: Cord grips hold the fixture weight only. DO NOT pull on the fixture during installation or cleaning which may cause the power wires to nick and short. 2: Push each cable through the cord grips on the canopy. Push the cord grip to release the cable. NOTE: If cable is curled or kinked, straighten by holding between the shaft of a screwdriver and thumb and pulling the cable through. 2 CORD GRIP CABLE G CABLE 3 CANOPY WIRE STRIPPERS 3: Use the #16 gauge hole of the AWG wire strippers to strip 1/2" of the outer plastic insulation from the cables. BARE WIRE 1/2" 3 INSULATION CABLE 2 H HOT LINE 5 BLACK NEUTRAL 4 WHITE 24V POWER SUPPLY 4: Connect the neutral wire to the white wire of the power supply using a wire nut. 5: Connect the hot line to the black wire of the power supply using a wire nut. 24VDC- 24VDC + 6: Connect the wire marked 24VDC+ to the red power supply wire using a wire nut. I 7: Connect the wire marked 24VDC- to the black power supply wire using a wire nut. NOTE: For ELV dimming, Triac or no dimming option, cap the 0-10V wire ends with wire nuts. 0-10V wires are not used. 8: Connect the 0-10V+ purple wire of the power supply to the 0-10V+ wire of the dimmer/switch using a wire nut. 9: Connect the 0-10V- gray wire of the power supply to the 0-10V- wire of the dimmer/switch using a wire nut. CAUTION: Test the fixture before removing the labels. 9 8 0-10V+ 0-10V- 6 24V POWER RED SUPPLY BLACK 7 J For Models Configured with Fast Jack Port: 10 12V 12V 12V POWER SUPPLY 12 BLACK LINE WHITE NEUTRAL 11 10: Connect each low voltage red wire from the power supply to each red wire of the Fast Jack connector using a wire nut. 11: Connect the neutral power wire from another 120VAC circuit to the white wire of the power supply with a wire nut. 12: Connect the line wire from the same 120VAC circuit to the black wire of the same power supply with a wire nut. K 13 14 14 13: Place all the wires and wire nut connections inside the canopy. 14: Align and secure the canopy to the mounting plate by tightening the four Phillips head screws. CANOPY 3 L CORD GRIP 15 CABLE 15: To make any adjustments to the fixture height, push the cord grips to slide the fixture up and down until the desired height is achieved. Release the cord grips to lock the cables in place. Section Three: Install Additional Support M1 1 CEILING NOTE: Follow these steps if the fixture (72 inches or longer) is provided with additional supports. 1: Lift the other end of the aircraft cables against the ceiling to mark the location of the standoffs. PENCIL AIRCRAFT CABLE SLIDING POST N NOTE: Steps 2 and 3 are for drywall mounting. Omit these steps if mounting to a wood surface directly. 2: Tap the anchors onto the marked points up to the threaded 2 portion with a hammer. 3: Screw in the threaded portion of the anchors with a Phillips screwdriver. CEILING ANCHOR 3 ANCHOR MUST BE FLUSH TO WALL O WASHER WITH THREADED NIPPLE #8 SCREW 4 STANDOFF POST 4: Feed the #8 screw through the washer with threaded nipple into the anchor. 5: Tighten the #8 screw completely into the anchor. 5 6: Tighten the standoff post completely onto the threaded nipple. 6 4 P EXCESS AIRCRAFT CABLE 9 AIRCRAFT CABLE 8 STANDOFF POST 7 7: Feed the aircraft cable coming from the channel through the standoff post. 8: Adjust the fixture height by pushing the tab and pulling the aircraft cable out of the side of the standoff post. Release the tab to secure the cable in place. 9: If necessary, trim excess aircraft cable using sharp cutters. General Wiring Diagrams ELV and Triac Dimming N INPUT 120-277VAC N GND LINE N ELV DIMMER LOAD N INPUT 120VAC GND LOAD LINE OPTIONAL FAST JACK ELV DIMMER 12V POWER SUPPLY 24V POWER SUPPLY +010V -010V DO NOT USE 0-10V WIRES +24V -24V CENTER FEED WITH FAST JACK PORT (FIXTURE SOLD SEPARATELY) LINEAR SUSPENSION CENTER FEED FIXTURE 5 0-10V Dimming LINE INPUT 120-277VAC N -0-10V +0-10V LOAD GND 0-10V DIMMER N L N N INPUT 120VAC GND LOAD LINE OPTIONAL FAST JACK ELV DIMMER 12V POWER SUPPLY 24V POWER SUPPLY +010V -010V +24V -24V CENTER FEED WITH FAST JACK PORT (FIXTURE SOLD SEPARATELY) LINEAR SUSPENSION CENTER FEED FIXTURE 6