Instruction Manual for i Board models including: IB-064C Running Board 4 Black, IB-064C, Running Board 4 Black, Board 4 Black, 4 Black, Black
HD Ridez Running Board 4" Black Compatible with Dodge Dakota 2005-2011 Club Cab (Nerf Bar Side Steps Side Bars) : Automotive
Auto Parts & Auto Accessories - Over 4000 Auto Parts, Aftermarket Parts, Truck Accessories & Car Accessories
iBoard®
iBoard® by APS
PART#: IB-064C&H
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
*BODY FRAME MOUNT *NO DRILLING REQUIRED
Fastener Size 6mm 8mm 10mm 12mm 14mm
Tightening Torque (ft-lbs) 6-7 16-18 31-32 56-58 92-94
Required
X
PART LIST Driver Side Step Bar
Front
Passenger Side Step Bar
Driver Front Support Bracket (DFS/PFS)
Driver Front Mounting Bracket (DFM)
Passenger Front Mounting Bracket
(PFM)
(DFS/PFS)
Driver Rear Support Bracket (DRS)
Passenger Rear Support Bracket (PRS)
Driver Rear Mounting Bracket (DRM)
Passenger Rear Mounting Bracket (PRM)
Note: Driver & Passenger Front Support Brackets are universal.
Customer Support: info@iboardauto.com 1
Rev. 20230401
iBoard®
Hardware Package A (For Bracket Installation)
Item QTY
Description
Item QTY
Description
1# 6 M10X1.5-30mm Hex Bolts
8# 2 M8X1.25-25mm Hex Bolts
2# 12 M10 Large Flat Washers
9# 4 M8 Large Flat Washers
3# 6 M10 Lock Washers
10# 2 M8 Nylon Lock Nuts
4# 6 M10 Hex Nuts
11# 2 M6X1-30mm Hex Bolts
5# 2 M12X1.75-100mm Hex Bolts
12# 4 M6 Flat Washers
6# 4 M12 Large Flat Washers
13# 2 M6X1 Nylon Lock Nuts
7# 2 M12 Nylon Lock Nuts
1#
2#
3#
4#
5#
6#
7#
8#
9#
10#
11#
12#
13#
Hardware Package B (For Stainless Steel Step Bar Installation)
Item QTY
Description
Item QTY
Description
1# 8 M8X1.25-35mm Carriage Bolts
3# 8 M8 Nylon Lock Nuts
2# 8 M8 Large Flat Washers
4# 4 Sliders (Packed with Step Bars)
1 #
2 #
3 #
4 #
Customer Support: info@iboardauto.com 2
Rev. 20230401
iBoard®
STEP 1
Start installing from the passenger side front of the vehicle. Remove the passenger front body mount bolt.
(1) M12X1.75-100mm Hex Bolt (2) M12 Large Flat Washers (1) M12 Nylon Lock Nut
STEP 2
Assemble Passenger Front Mounting Bracket (PFM) and Passenger Front Support Bracket (DFS/PFS) with (2) M10X1.530mm Hex Bolts, (4) M10 Large Flat Washers, (2) M10 Lock Washers and (2) M10 Hex Nuts, (Fig 1). Do not fully tighten hardware at this time.
(2) M10X1.5-30mm Hex Bolts
(4) M10 Large Flat Washers
(2) M10 Lock Washers
PFM
(2) M10 Hex Nuts
DFS/PFS PFM
Factory Bolt
(Fig 2) Passenger Side Front Brackets Installation
STEP 4
Move to the passenger side rear mounting location. Remove the passenger rear body mount bolt.
DFS/PFS (Fig 1) Passenger Side Front Brackets Assembly
STEP 5
Assemble Passenger Rear Mounting Bracket (PRM) and Passenger Rear Support Bracket (PRS) with (1) M10X1.5-30mm Hex Bolt, (2) M10 Large Flat Washers, (1) M10 Lock Washer and (1) M10 Hex Nut, (Fig 3). Do not fully tighten hardware at this time.
PRM
STEP 3
Attach the assembled Passenger Front Mounting Bracket (PFM) to the vehicle with factory bolt, (Fig 2 & 3).
Attach Passenger Front Support Bracket (DFS/PFS) to smaller factory hole in the frame using (1) M12X1.75-100mm Hex Bolt, (1) M12 Nylon Lock Nut, (2) M12 Large Flat Washers, (Fig 2 & 3). Do not fully tighten hardware at this time.
PRS
(2) M10X1.5-30mm Hex Bolts (4) M10 Large Flat Washers (2) M10 Lock Washers (2) M10 Hex Nuts
(Fig 3) Passenger Side Rear Brackets Assembly
Customer Support: info@iboardauto.com 3
Rev. 20230401
iBoard®
STEP 6
Attach the assembled Passenger Rear Mounting Bracket (PRM) to the vehicle with factory bolts, (Fig 4 & 5).
Attach Passenger Rear Support Bracket (PRS) to the factory hole on the inner side of body mount cavity and closer to the frame using:
05-07 Models:
(1) M8X1.25-25mm Hex Bolt, (1) M8 Nylon Lock Nut, (2) M8 Large Flat Washers (Fig 4). Do not fully tighten hardware at this time.
08-On Models:
(1) M6X1-30mm Hex Bolt, (1) M6 Nylon Lock Nut, (2) M6 Flat Washers (Fig 5). Do not fully tighten hardware at this time.
05-07 Models: (1) M8X1.25-25mm Hex Bolt (2) M8 Large Flat Washers (1) M8 Nylon Lock Nut
STEP 7
Once all (2) Passenger side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 6 & 7)
(1) Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
(2) Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
(3) Slide the Slider (with carriage bolts) to the Step Bar.
(4) Repeat to install the other (1) slider to the step bar.
(5) Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers and (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 7). Do not fully tighten hardware at this time.
Note: The Sliders are packed with the Step Bars.
Level and adjust the Step Bar and fully tighten all hardware.
Repeat Steps 1-7 for the other side Step Bar installation. The installation is completed!!!
PRS PRM
Factory Bolt (Fig 4) Passenger Side Rear Brackets Installation (05-07 Models)
Factory Bolt
PRM
Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.
08-On Models: (1) M6X1-30mm Hex Bolt PRS (2) M6 Flat Washers (1) M6 Nylon Lock Nut
(Fig 5) Passenger Side Rear Brackets Installation (08-On Models)
Customer Support: info@iboardauto.com 4
Rev. 20230401
iBoard®
Slider
(2) Carriage Bolts
(Fig 6) Slider Installation
Slider with (2) Carriage Bolts
Step Bar
Slider (w/ installed Carriage Bolts)
Step Bar (Bottom View)
Mounting Bracket
(2) M8 Large Flat Washers (2) M8 Nylon Lock Nuts
(Fig 7) Step Bar Installation
Customer Support: info@iboardauto.com 5
Rev. 20230401
Microsoft Publisher LTSC