Blink HQ 200 – Level 2 AC EVSE Installation Manual

Important Safety Instructions

Before installing or using the Blink Electric Vehicle Supply Equipment (EVSE), read all instructions, paying particular attention to WARNING and CAUTION markings. Review any instructions included with your electric vehicle (EV) for vehicle charging. The following symbols and associated instructions are used throughout this document to avoid hazards:

Legend

• WARNING: RISK OF ELECTRIC SHOCK: Used when there is a risk of personal injury.
• WARNING: RISK OF ELECTRIC SHOCK: Used when there is a risk of electric shock.
• WARNING: RISK OF FIRE: Used when there is a risk of fire.
• CAUTION: Used when there is a risk of damage to the equipment.

General Safety Guidelines:

• This product should be installed only by a qualified approved technician.
• Blink is not responsible for physical injury, damage to property or equipment caused by the installation of this device.
• Ensure that pressure terminal connectors for field wiring connections are provided with instructions specifying a range of values or a nominal value of tightening torque for the clamping screws.
• Ensure that materials used and installation procedures follow local building codes and safety standards.
• The information in this manual does not exempt the user from the responsibility to follow all applicable codes or safety standards.
• Review this manual carefully and consult with a licensed contractor, licensed electrician, or trained installation expert to ensure compliance with local building codes and safety standards.

Repair and Maintenance Clause

• Only a licensed contractor, licensed electrician, or trained installation expert is allowed to repair or maintain this device. General users are forbidden from repairing or maintaining this device.
• Any repair or maintenance MUST be performed after removing power from this device.

Moving and Storage Instructions

• Store the product at a temperature between -40 and +80 °C.
• Check product for damage after moving.
• Carry the product by the sides. Do not lift or carry by the flexible cord or the EV cable.

FCC Rules and Industry Canada License-Exempt RSS Standard(s)

• This device complies with Part 15 of the FCC Rules. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
• English: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
• French: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

WARNING: RISK OF ELECTRIC SHOCK

Basic precautions should always be followed when using electrical products:

• Read all instructions before using this product.
• This device should be supervised when used around children.
• Do not put fingers into the EV connector.
• Do not use this product if the flexible power cord or EV cable is frayed, has broken insulation, or any other signs of damage.
• Do not use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage.

WARNING: RISK OF ELECTRIC SHOCK

Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded.

• Do not touch live electrical parts.
• Incorrect connections may cause electric shock.

WARNING: RISK OF ELECTRIC SHOCK

This equipment is intended only for charging vehicles that do not require ventilation during charging. Please refer to your vehicle's owner's manual to determine ventilation requirements.

WARNING

Do not use extender cables to increase the length of the charging cable. The maximum length is limited to 25 feet by the National Fire Protection Agency.

CAUTION

To reduce the risk of fire, connect only to a circuit provided with Model HQW2-50C-W1-N1-N-23, HQW2-50C-N1-N1-N-23, HQW2-50C-W1-N2-N-23-D for 50 A; Model MQW2-50C-M2-R1-N-23, HQW2-50C-W1-N1-N-23, HQW2-50C-N1-N1-N-23, MQW2-50C-M2-R2-N-23-D, HQW2-50C-W1-N2-N-23-D for 62.5 A amperes maximum branch circuit overcurrent protection in accordance with the National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical Code, Part I, C22.1.

General Conventions: The use of the word “Note:” indicates additional information relevant to the current process or procedure.

Introduction

This INSTALLATION MANUAL describes how to properly install the Blink HQ 200 – Level 2 AC EVSE (Blink Product). Contact the Blink Support Center at (888) 998 2546 for troubleshooting assistance and additional technical questions. Unauthorized modification to the Blink product will void manufacturer's warranty.

The Blink Product specified in this document is designed for the North American market to charge plug-in electric vehicles (PEVs), plug-in hybrid electric vehicles (PHEVs), and battery electric vehicles (BEVs). It provides Level 2 AC charging that shortens the charging time for typical EVs, when compared to a Level 1 AC EVSE.

Product Overview

Product Specifications

POWER SPECIFICATIONS

FUNCTIONAL SPECIFICATIONS

NETWORK SPECIFICATIONS

SAFETY & COMPLIANCE SPECIFICATIONS

OPERATIONAL SPECIFICATIONS

Blink reserves the right to alter product offerings and specs at any time without notice and is not responsible for typographical or graphical errors that may appear in this document.

Pre-Installation Instructions

Safety and Grounding

Safety Check

CAUTION: DISCONNECT ELECTRICAL POWER PRIOR TO INSTALLING THE BLINK CHARGING STATION. FAILURE TO DO SO MAY CAUSE PHYSICAL INJURY OR DAMAGE TO THE ELECTRICAL SYSTEM AND BLINK PRODUCT.

The Blink Product should be installed only by a licensed contractor, and/or a licensed electrician in accordance with all applicable state, local and national electrical codes and standards.

Before installing the Blink Product, review this manual carefully and consult with a licensed contractor, licensed electrician and trained installation expert to ensure compliance with local building practices, climate conditions, safety standards, and state and local codes.

Use appropriate protection when connecting to the main power distribution cable. Use tools as outlined in the "Tools Required for Installation" section.

Grounding Instructions

This product must be connected to a grounded, metal, permanent wiring system; and an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product.

Installation Instructions

Tools Required for Installation

Parts Required for Installation

Wire Size and Temperature

Product Installation

STEP 1: Remove front cover screws.

STEP 2: Remove the front cover.

STEP 3: Remove the installation cover screws.

STEP 4: Remove installation cover.

Diagram showing an exploded view of the HQ 200 Charger with labels for M4 TORX SCREW (TOP COVER), TOP COVER, DIP SWITCH, M4 TORX SCREW (INSTALLATION COVER), and INSTALLATION COVER.

Diagram showing the internal components of the HQ 200 Charger with a DIP SWITCH labeled.

STEP 5: Set maximum current by configuring the DIP switch using the following table:

WARNING: Power must remain off before changing the DIP switch.

STEP 6: Secure the main body mounting bracket to the wall with appropriate screws.

Follow applicable accessibility requirements for the mounting position. The unit shall be stored or located at a sufficient height above the floor. For an indoor site, it should be not lower than 18" (450 mm) and not higher than 4' (1.2m). For an outdoor site, it should be not lower than 24" (600 mm) and not higher than 4' (1.2m). Refer to Article 625, NEC.

The mounting bracket has six screw holes for wall mounting. If only two screws are used for mounting, the screws should pass through the middle two screw holes of the mounting bracket. The other screw holes are reserved for the user.

Diagram showing a mounting bracket with arrows indicating where M6 screws should be inserted for mounting.

A. For masonry walls, use M6 mechanical screws (commercially available).

B. For finished walls supported by wood studs, use #12 self-tapping screws.

C. Please refer to the following torque. The actual torque is according to the wall material.

Diagram showing the HQ 200 charger being attached to the mounting bracket with a locking screw.

STEP 7: Hang the product on the mounting bracket.

STEP 8: Slide down the product to rest on the bottom flange.

STEP 9: Install the locking screws (M4 Torx).

STEP 10: Reassemble the install cover and front cover with M4 screws.

Charging Status Indicators

Diagram showing the front of the Blink HQ 200 charger with a circular LED Status Indicator highlighted.