3 in 1 Wireless Charging Station

Product Information

Name: 3 in 1 Wireless Charging Station
Input Voltage: DC 9V/3A, 12V/2.5A
Output (Mobile Phone): 5W/7.5W/10W/15W
Output (Headphone): 5W
Output (Watch): 3W
Size: 90*95*130mm
Conversion Rate: <80%
Material: Aluminum Alloy-ABS
Color: Silver, Black
Standard: Wireless charging, data cable manual

Instructions for Use

When power is on, the indicator light flashes blue/green alternately then goes out. A solid blue light indicates standby mode. A solid green light indicates charging mode. The light goes out when fully charged. A rapidly flashing red light indicates a foreign object in the charging area.
Phones without Magsafe magnetic suction require a magnetic ring or a phone case with a magnetic ring for use.
Place the phone into the charging area and align the charging position automatically. The green light in the center will stay on while the phone is charging.
Place the watch into the watch charging area and align the charging position automatically. The green indicator light will stay on while the watch is charging.
Place the earphone into the earphone charging area. The green indicator light will stay on while the earphone is charging.
The product supports the Qi protocol for all compatible mobile devices. The green indicator light will stay on when the device is charging.
In case of an abnormality, the red indicator light will flash, or automatic shutdown protection will engage.

Safety Notice

Do not pull the power cord forcibly to prevent it from breaking or falling off.
Do not disassemble or throw the device into fire or water to avoid short circuit leakage.
Do not use in severe high temperature, humid, or corrosive environments to avoid damage to the circuit and leakage.

Frequently Asked Questions

1. Slow charging

The phone itself or the external receiving coil may allow a different amount of wireless charging current, or applications running on the phone may consume a lot of power. It is recommended to reduce or close running applications.

2. Intermittent charging / Blinking indicator light / Insufficient charging current

Please use a charging head (adapter) with a full power output of 9V/2A or OC3.0 or higher.

3. Charging heat

During the wireless charging process, it is normal for the receiving coil or transmitter board to heat up. It is recommended to adjust the charging position.

4. Charger does not work

Do not place metal objects or magnetic cards in the charging area. If the product does not work due to overheating, please remove the phone and wait for it to cool down before trying to charge.

5. Main unit indicator light is normal, but the cell phone cannot be charged

This could be due to a cell phone receiving coil failure or the external magnetic suction piece charging position being inaccurate. Suggest adjusting the position of the external magnetic suction ring or repairing the cell phone.

6. Main unit indicator light does not light up

This indicates a main unit failure. Please contact after-sales service personnel.

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement: The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.