Installation Guide for FRENCH FITNESS models including: FFS-CSMP, FFT-CSMP, FFS-CSMP FFT-CSMP Shasta Tahoe Chest Shoulder Multi Press, FFS-CSMP FFT-CSMP, Shasta Tahoe Chest Shoulder Multi Press, Chest Shoulder Multi Press, Shoulder Multi Press, Multi Press
1 день назад — ASSEMBLY MANUAL. Page 2. FEATURES. • 11 Gauge Steel. • 50 x 100 mm thickness ... Relevant information is available on this instruction sheet as well as at ...
24 hours ago — ASSEMBLY MANUAL. Page 2. FEATURES. • 11 Gauge Steel. • 50 x 100 mm thickness ... Relevant information is available on this instruction sheet as well as at ...
FFS-CSMP / FFT-CSMP FRENCH FITNESS SHASTA / TAHOE CHEST/SHOULDER MULTI PRESS (NEW) ASSEMBLY MANUAL F E AT U RE S · 11 Gauge Steel · 50 x 100 mm thickness 3mm Steel tube · ASTM A36 steel frame ensures maximum structural integrity · Each frame receives an electrostatic powder coat finish to ensure maximum adhesion and durability · Standard rubber feet protect base of the frame and prevent the machine from slipping · Nylon-coated cable meets U.S. military specifications · Fiberglass-impregnated nylon pulleys feature sealed bearings · Grips retained with aluminum collars, preventing them from slipping during use · Hand grips are a durable urethane composite · Solid-steel weight plates. Top weight plate is fitted with self-lubricating bushings · Weight selector pin magnetically locks in place and is connected to stack to prevent loss · Standard rear shrouds TECH SPECS · (16) Weight Plate, EA 13.23 Lb (6 kg) · 212 lb Weight Stack (96 kg) · Top Weight Stack Selector Weights: (2) 5.5 lb (2.5 kg) Selector Plates for Incremental Weight Adjustments. · Weight to Pulley Ratio: 1:1 · Weight: 476 lb (216 kg) · Dimensions: 80"L x 55.5"W x 64.25"H · User Height Range: 4'11" to 6'5" (149.86 cm to 195.58 cm) WARRANT Y · 10 Years Parts, 1 Year Labor (Commercial) · California Residents see Prop 65 WARNING TABLE OF CONTENTS CAUTIONS .................................................................................. 4 PARTS LIST ................................................................................ 5 ASSEMBLY INSTRUCTIONS ...................................................... 6 CAU T I ONS Security precautions To ensure your safety, please read the following notes before using this product read, study and understand the instructions and all warning labels before use. 1. It is recommended to be familiar with the normal operation and usage of the apparat us before using this product. Relevant information is available on this instruction sheet as well as at local retailers . 2. Be sure to keep this specification and ensure that all warning labels are clear and complete. 3. This product is recommended for installation by more than two people. 4. Ask doctor for advice before you start exercising. 5. Please keep your hands, limbs and clothes stretch so that you can fully and safely use this device. 6. Note any possible signs of mechanical occurrence, including part wear, hardware loosening, and welding cracks. If any of the above signs immediately stop using this device and contact our after-sales service department. You can use a wrench to complete the assembly. 7. The user of this product shall not exceed 150 kg. 8. The right of final interpretation of the product is vested in the Company without prior notice of change. PARTS LIST ASSEMBLY INSTRUCTIONS STEP 1. Assemble the COUNTERWEIGHT FRAME : Connect A1, A2, A3 and A4 with corresponding screws STEP 2. Install the counterweight: Insert B1 into the hole corresponding to A1, and sIide 10, 11, 12, 13 and B2, B3, B4 into B1 STEP 3. Fix B1 at the corresponding hole position of A1 with corresponding screws STEP 4. Install the cabIe lnstall 11 on B1, and the other end passes through each pulley in turn, and then insert it into the hole oiB as shown in the figure and lock it with hexagon socket head screws. STEP 5. I nstall the counterweight frame safe board: lnstall 10 to C1 with corresponding screws at each hole position as shown 1n the figure STEP 6. I nstall the counterweight frame safe board lnstalI 10 to A1 with corresponding screws at each hole position as shown in the figure STEP 7. Install the sports sign: Uncover the double-sided adhesive tape on the counterweight frame and stick C2 at the position shown in the figure.Adobe PDF Library 21.7.123