Indoor architectural lighting | Ledalite | Signify
Installation Guide for signify models including: ID-7608, ID-7608 LED Wall Verge, LED Wall Verge, Wall Verge, Verge
Verge wall - Wall | Ledalite - Signify
File Info : application/pdf, 3 Pages, 798.99KB
DocumentDocumentSignify Classified - Internal Verge Wall LED Installation Instructions ID_7608_Verge_Wall_LED Standalone or continuous run configurations System Overview These instructions review how to install Verge wall mount fixtures. Verge 4 ftand 8 ft modules can be installed as individual standalone units, or they can be joined together to create continuous rows. The graphic below shows the components required to install a typical row of Verge wall mount fixtures. IMPORTANT: Read all instructions including fixture wiring AND mechanical details before beginning installation. Module Lengths Sync wall mount systems come in 4ft and 8ft modules. Overall module lengths are shown to the right. Module lengths do not include endcaps. Endcaps Add two endcaps to the overall length of each row. 4ft 4'-0" 8ft 8'-0 1/2" Indicates overall length of fixture (excluding endcaps) 6 1/16" 2 3/16" Verge Power Kits 1x j-box cover 1x strain relief Verge Joint Kits 4x 1/2" plug 2x #10-24 lock nut 2x #10-24 x 9/16" bolt 1x gasket Verge Left Endcap kit 1x left endcap 2x 1/2" plugs 2x #10-24 x 1/2" screw TOOLS REQUIRED: Stubby Phillips screwdriver, 3/8 " nut driver. Verge Right Endcap Kit 1x right endcap 2x 1/2" plugs 2x #10-24 x 1/2" screw Mount Spacing ©Mounts variable within 2" - 5" of end or joint. On 8ft module, additional mount to be located within 2" - 5" of center of module. ©Maximum distance between mounts is 48". Note: Fixture isflush with wall. Row Configurations The tables below indicate how 4ft and 8ft modules can be combined to create continuous rows of various lengths. Nominal row length 4' 8' 12' 16' 20' 24' 28' 32' 4ft module 1x 1x 1x 1x 8ft module 1x 1x 2x 2x 3x 3x 4x ! ATTENTION: Install in accordance with national and local building and electrical codes. ©2019 Signify Holding. All rights are reserved. Reproduction in whole or part is prohibited without the written consent of the copyright owner. Phone: 604.888.6811 Web: ledalite.com/products Revision D Page 1 November 17, 2023 Signify Classified - Internal Verge Wall LED Installation Instructions ID_7608_Verge_Wall_LED Standalone or continuous run configurations IMPORTANT: Read all instructions at least once prior to beginning installation. All mount brackets must be secured to wall structure (eg. studs or cross-braces). This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interreference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 1 Install utility box and utility box cover cover bracket Attach cover plate to utility box strain relief Determine power feed location and install 2"x4" utility box (supplied by others) parallel with fixture. Complete connections at utility box with supplied power cord. Attach cover bracket using supplied hardware. Punch power access hole in supplied cover, feed power cord through and attach strain relief on wall side. Attach cover using supplied painted hardware. NOTE: Bottom of utility box should be in line with bottom of wall brackets. 2 Install wall brackets wall bracket Bottom of utility box should be in line with bottom of wall brackets. Determine fixture mounting location and secure wall brackets to structure using appropriate fasteners (two per bracket, supplied by others). 4ft fixtures: Require two bracket assemblies; 8ft fixtures: Require three bracket assemblies. Brackets must be installed a maximum of5" from end of fixture (on 8ft fixture, the third bracket can be 5" of ether side of inrow crossplate). NOTE: Mounted fixture(s) will sit approximately /4" above top edge of bracket assembly. 3 Unpack / Prepare fixtures Arrange boxed fixtures on floor in specified locations; remove fixtures from boxes; remove plastic from fixtures. Cap all unnecessary power feed holes at back of fixture(s) using supplied 1/2" plugs. 4 Remove Top Reflector 4b Remove Front Reflector 5 Raise Fixture and Engage on Wall Brackets Secure bracket 6 Access Wiring / Remove Pan Shift top reflector to the left and then remove the reflector. Remove the screws holding the front reflector and then remove the front reflector. With 2 people, raise fixture into position and engage it on hooks located on top of wall brackets, then rotate it down into position. Secure bracket using supplied hardware. POWER LOCATIONS: Prior to engaging fixture in mounting brackets, feed installed power cord through the access hole at back of the fixture. To access wiring, remove screw from top pan and lift pan off. Apply strain relief to power cord. NOTE: Care should be taken when lifting up top reflector to avoid disconnecting internal wiring. ! ATTENTION: Install in accordance with national and local building and electrical codes. ©2019 Signify Holding. All rights are reserved. Reproduction in whole or part is prohibited without the written consent of the copyright owner. Phone: 604.888.6811 Web: ledalite.com/products Revision D Page 2 November 17, 2023 Signify Classified - Internal Verge Wall LED 7 Complete electrical connections strain relief Installation Instructions ID_7608_Verge_Wall_LED 8 Level and secure first fixture tilt screw lock screw Standalone or continuous run configurations 9 Install and join additional fixtures to create row gasket 10 Complete electrical connections at joints wirenuts (supplied by others) Complete electrical connections using wire nuts (supplied by others). Re-install pan and hardware removed in S T E P 5. 11 Level and secure additional fixture gasket TOP VIEW OF BRACKET LEVEL: Using 5/16" hex nut driver, level fixture by adjusting the tilt screw. S EC U R E: Secure fixture to wall bracket assemblies by tightening the lock screw. 12 Install Endcaps With two people, raise second fixture and engage on mounting brackets (see S T E P 4). At joint, remember to insert black gasket. 13 Re-install Front Reflector quick-wire connectors (supplied) wire nuts (by others) Complete in-row electrical connections. NON-POWER LOCATIONS: Use supplied quick-wire connectors. Tuck wires into wire cavity. POWER LOCATIONS: Remove installed quick-wire connectors and complete electrical connections using wire nuts (supplied by others). Tuck wires into wiring cavity. NOTE: Use smallest appropriate wire nuts. 14 Install Light Guide and Re-install Top Reflector Level second fixture by adjusting the tilt screw (see step 8). Slide second fixture flush against first fixture and secure joint using supplied nut and bolt hardware (requires 3/8 nut drivers). Secure fixture to wall brackets by tightening the lock screw at each bracket location (see step 8). Repeat steps 8-10 for each additional fixture(s) in row. Attach endcap to first and last module in each row using supplied hardware. IMPORTANT: Do not over-tighten endcap fasteners. Ledalite recommends tightening fasteners by hand. When nut is flush with crossplate, turn an additional /4 turn. Re-install front reflector using short (stubby) screwdriver. Identify smooth side of the Light Guide and ensure it is installed smooth side DOWN. Install Light Guide panel into LED fixture after joining and wiring is complete. Ensure panel isseated correctly as shown above. Final Step: Install the top reflector and shift into place. ! ATTENTION: Install in accordance with national and local building and electrical codes. ©2019 Signify Holding. All rights are reserved. Reproduction in whole or part is prohibited without the written consent of the copyright owner. Phone: 604.888.6811 Web: ledalite.com/products Revision D Page 3 November 17, 2023