Hikvision DS-PR1-WE/WB Wireless Repeater

About this Manual

This manual provides instructions for using and managing the Hikvision DS-PR1-WE/WB Wireless Repeater. Information is subject to change without notice due to firmware updates. The latest version is available on the Hikvision website (https://www.hikvision.com/). Use this manual with guidance from trained professionals.

Hikvision trademarks and logos are properties of Hikvision. Other trademarks belong to their respective owners.

Disclaimer

Hikvision provides the product "as is" without warranties. Hikvision is not liable for damages arising from product use, including business losses, data corruption, or indirect damages, even if advised of the possibility. Hikvision is not responsible for abnormal operation or privacy leakage due to internet security risks like cyber-attacks or viruses, but will provide technical support. Users must comply with all applicable laws and ensure their use does not infringe third-party rights. Prohibited uses include developing weapons of mass destruction or supporting human rights abuses. In case of conflict between this manual and applicable law, the law prevails.

Product Compliance

The product is marked with "CE" and complies with applicable European standards under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU, and RoHS Directive 2011/65/EU.

WEEE Directive (2012/19/EU): Products marked with this symbol cannot be disposed of as unsorted municipal waste. Return to your local supplier or designated collection points for recycling. More information: www.recyclethis.info

Battery Directive (2006/66/EC): Contains a battery that cannot be disposed of as unsorted municipal waste. Refer to product documentation for battery information. The battery may be marked with symbols indicating Cadmium (Cd), Lead (Pb), or Mercury (Hg). Return batteries to your supplier or designated collection points for recycling. More information: www.recyclethis.info

Battery Safety Cautions:

• Risk of explosion if battery is replaced with an incorrect type.
• Do not dispose of batteries in fire or hot ovens, or crush/cut them.
• Avoid batteries in extremely high temperatures or low air pressure environments.
• Keep new and used batteries away from children.
• Seek immediate medical attention if batteries are swallowed or placed inside any part of the body.
• Replace all batteries at the same time; do not mix old and new batteries.
• Dispose of used batteries according to manufacturer instructions and local regulations.

1 Appearance

The Hikvision DS-PR1-WE/WB Wireless Repeater is a compact device designed to extend the range of wireless security systems.

Device Indicators and Ports:

• 1. Fault Indicator: (LED) Indicates device faults.
• 2. Signal Strength Indicator: (LED) Shows the signal strength from the control panel.
• 3. Power Indicator: (LED) Indicates the power status.
• 4. Tamper Switch: An internal switch that detects if the device casing has been opened.
• 5. Power Switch: A physical button to turn the device on or off.
• 6. Serial Port: A connector, likely for diagnostics or initial setup.
• 7. Power Interface: The port for connecting the power adapter.

Visual Description: The device is a white rectangular unit. The front panel features several indicator LEDs and ports. A diagram shows these components labeled 1 through 7.

Cautions:

• If the battery compartment does not close securely, stop using the product and keep it away from children.
• Chemical burning danger: Do not swallow the battery. Keep new and used batteries away from children.

2 Enrollment

Enrollment is the process of adding the repeater to a compatible control panel. The process typically completes in 3 to 10 seconds.

Method 1: Enroll the Peripheral Locally

1. On the control panel's mobile app, tap the "Enrollment Mode" button to put the control panel into enrollment status.
2. Loosen the screw on the repeater and remove its rear panel.
3. Power on the repeater; it will be automatically enrolled to the control panel.

Visual Description: A sequence of images shows a smartphone with an app interface, a QR code, and the repeater's rear panel being opened. The note indicates the distance between the peripheral and the AX PRO control panel should be less than 50 cm.

Method 2: Enroll the Peripheral with QR and Serial No.

1. In the app, tap the "+" icon.
2. Scan the QR code or enter the serial number found on the peripheral.
3. Loosen the screw and remove the rear panel of the repeater.
4. Power on the repeater; it will be automatically enrolled to the control panel.

Visual Description: A diagram illustrates using a smartphone app to scan a QR code or input a serial number to add a device.

Note for Re-enrollment: To re-enroll the device, power it off, hold the tamper switch, and then power it on synchronously.

3 Installation

Proper installation ensures optimal performance and signal strength.

3.1 Check Signal Strength

Enter the signal checking mode on the control panel. The repeater's indicators will show the signal status:

• Solid Green for 3 seconds: Strong Signal
• Solid Orange for 3 seconds: Medium Signal
• Solid Red for 3 seconds: Weak Signal
• Red light flashes for 3 seconds: Failure

Visual Description: A diagram shows a hand holding the repeater, with a "Signal Strength Test" indicator displaying signal bars and color codes (Green checkmarks for strong, orange for medium, red crosses for weak/failure).

3.2 Install the Device

1. Cable Routing: Route the power cable through the bottom cable hole or a knock-out cable hole.
2. Mounting: Mount the device securely to a wall. The diagram shows mounting using screws (e.g., KA3x25).

Visual Description: Diagrams illustrate routing a cable through the bottom of the device and mounting the device to a wall using screws.

4 Set up with App

Configure and manage the repeater using the Hikvision mobile application.

1. On the device list page of the app, tap the AX PRO control panel and log in if required.
2. Navigate to the Repeater device. You can view its status, including battery, mains power, signal strength, connection status, connected devices, and lid status.
3. Tap the settings icon (typically in the upper right corner) to access configuration options.

App Functions:

5 Operation Caution and Device Maintenance

Follow these guidelines for safe operation and to prevent damage:

• Comply with all local electrical safety, fire prevention, and related regulations.
• Do not drop the device or subject it to physical shock. Avoid installation on vibrating surfaces or places prone to shock, as this can cause damage.
• Ensure power is disconnected before wiring, installing, or dismantling the device.
• If smoke, odors, or unusual noise occurs, turn off the power immediately, unplug the power cable, and contact the service center.
• Avoid high electromagnetism radiation.
• Do not place the device in extremely hot, cold, dusty, or damp locations.
• Keep the device for indoor use away from rain and moisture.
• Do not expose the equipment to direct sunlight, low ventilation, or heat sources like heaters or radiators.
• Do not aim the device at the sun or excessively bright places, as this may cause blooming or smearing, affecting sensor endurance.
• Improper battery use or replacement can lead to explosion hazards. Use only the same or equivalent battery type. Dispose of used batteries according to manufacturer instructions and local regulations.
• Do not expose the device to corrosive gas, as it may cause damage.
• Do not expose the device to explosive situations.

6 Specification