Aftermarket ATV-UTV Parts and Accessories
Installation Guide for SUPERATV models including: SPK-P-RAN1KXP-001, Plow Pro 72 Inch Snow Plow, Plow Pro, 72 Inch Snow Plow, Snow Plow
Polaris Ranger XP 1000 Plow Pro Snow Plow by SuperATV - SPK-P-RAN1KXP-02-XX
File Info : application/pdf, 13 Pages, 1.58MB
DocumentDocumentINSTALLATION INSTRUCTIONS Snow Plow Mount: for Polaris Ranger® XP 1000 2753 Michigan Road · Madison, Indiana 47250 · 855-743-3427 Do not discard packaging until product has been successfully installed. SPK-P-RAN1KXP-001 Mount Hitch and Cotter Pin x 2 Frame Bracket x 2 SPK-P-RAN1KXP Mount Need help with your installation? sales@superatv.com www.superatv.com 1-855-743-3427 8:00am - 9:00pm EST M-Th 8:00am - 7:00pm EST Friday 9:00am - 2:00pm EST Saturday Read instructions and view illustrations before beginning. Thank You For Choosing © 2022 SuperATV.com®. All Rights Reserved. IN-SPM-P-RAN1KXP ~ IN-SPM-P-RAN1KXP-001 1/17/2022 Remove any Skid Plate from front of machine. SuperATV Skid Plate shown. SPK-P-RAN1KXP-001 SuperATV Bumper installation - Install Mount to machine with hardware shown. Tighten hardware. 4 each M10 x 30mm M10 Nut (driver side) * IN-SPM-P-RAN1KXP ~ IN-SPM-P-RAN1KXP-001 Depending on setup, longer bolts may be required * * M10 x 40mm 2 SPK-P-RAN1KXP-001 SuperATV Bumper installation con't - Install Frame Brackets to Plow Frame as shown with hardware shown. - Tighten hardware. (right side) short side (left side) long side 8 each - Join Plow Frame to Mount with hardware shown. M12 x 30mm M12 Nut Hitch and Cotter Pin x 2 IN-SPM-P-RAN1KXP ~ IN-SPM-P-RAN1KXP-001 (driver side) 3 Latch SPK-P-RAN1KXP Stock Bumper installation - Remove Pin from Mount and place Latch in open position. - Repeat for opposite side. Pin Mount - Place Mount around Frame, close each Latch, and secure with Pins. IN-SPM-P-RAN1KXP ~ IN-SPM-P-RAN1KXP-001 4 SPK-P-RAN1KXP Stock Bumper installation con't - Join Plow Frame to Mount with hardware shown. - Tighten hardware. 8 each M12 x 30mm M12 Nut Liability Statement SuperATV's® products are designed to best fit user's ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV's® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV® to verify that they will work together. Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product's ability to protect user from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing SuperATV® products, user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers' products will not be covered by SuperATV®. SuperATV® parts and products are not warrantied if item was not installed properly, misused, or modified. Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you. The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof. IN-SPM-P-RAN1KXP ~ IN-SPM-P-RAN1KXP-001 5 2753 Michigan Road · Madison, Indiana 47250 · 855-743-3427 INSTALLATION INSTRUCTIONS Snow Plow Blade Do not discard packaging until product has been successfully installed. Blade Liability Statement SuperATV's® products are designed to best fit user's ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV's® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV® to verify that they will work together. Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product's ability to protect user from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing SuperATV® products, user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers' products will not be covered by SuperATV®. SuperATV® parts and products are not warrantied if item was not installed properly, misused, or modified. Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you. The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof. Need help with your installation? sales@superatv.com www.superatv.com 1-855-743-3427 8:00am - 8:00pm EST M-Th 8:00am - 7:00pm EST Friday 9:00am - 2:00pm EST Saturday © 2022 SuperATV.com®. All Rights Reserved. Read instructions and view illustrations before beginning. Thank You For Choosing IN-SPB-U-001 1/18/2022 - Adjust Skid Pads after Blade, Snow Plow Mount, and Snow Plow Frame are installed to machine. - Blade height will depend on what type of surface is to be plowed. Use provided Spacers to achieve desired height. Skid Pad Premature wear may occur if operating on asphalt or concrete. Notes: - To reduce icing, allow Blade to reach same temperature as outdoors before beginning. - Except for when pivoting Blade, always place Blade on ground before exiting vehicle. - To avoid damaging Blade, do not plow over pipes, roots, curbs, or other large objects. - Treating Blade with automotive type paste wax will make snow easier to move off Blade. - Inspect Blade for loose, worn, or damaged components before plowing. Correct any issues. - Clean Blade after each use and before storing long term. - Use touch up paint, or a light coat of oil or grease, on any bare metal. - Lubricate all pivot points before each seasons use. - Store Blade away from weather and in a dry area after each use. IN-SPB-U-001 2 INSTALLATION INSTRUCTIONS 2753 Michigan Road · Madison, Indiana 47250 · 855-743-3427 Snow Plow Frame Do not discard packaging until product has been successfully installed. Plow Frame Liability Statement SuperATV's® products are designed to best fit user's ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV's® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV® to verify that they will work together. Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product's ability to protect user from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing SuperATV® products, user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers' products will not be covered by SuperATV®. SuperATV® parts and products are not warrantied if item was not installed properly, misused, or modified. Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you. The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof. Need help with your installation? sales@superatv.com www.superatv.com 1-855-743-3427 8:00am - 8:00pm EST M-Th 8:00am - 7:00pm EST Friday 9:00am - 2:00pm EST Saturday © 2022 SuperATV.com®. All Rights Reserved. Read instructions and view illustrations before beginning. Thank You For Choosing IN-SPF-U-001 1/18/2022 - Install Plow Frame to Blade with hardware shown. Tighten hardware. 2 each M12 x 55mm M12 Nut IN-SPF-U-001 2 - Install Eye Bolts and Adjustment Blocks to Plow Frame with hardware shown. - Hook Plow Springs into Eye Bolts. - Do not tighten hardware. Plow Spring Eye Bolt and Nut (Blade shown off for clarity) Adjustment Block* 2 each M10 x 40mm M10 Nut Adjustment Block - *Adjustment Blocks can be rotated to offer more adjustability. See page 5. - All machines are different and orientation may vary. IN-SPF-U-001 3 - Secure Plow Springs to Blade. - Tighten Nuts on Eye Bolts until desired Plow Spring tension is achieved. IN-SPF-U-001 4 - Adjustment Blocks in frontmost holes will tilt Blade forward or vertical. - Moving to rearmost holes will tilt Blade backward. Blade should be 90° or slightly forward for proper break-over function IN-SPF-U-001 5 (Blade shown off for clarity) To adjust Blade direction, remove Pin and move Linkage until desired angle is acheived. Resecure with Pin. IN-SPF-U-001 6