Instruction Manual for MIBOXER models including: MR2 Mini Single Color LED Controller 2.4GHz, MR2, Mini Single Color LED Controller 2.4GHz, Single Color LED Controller 2.4GHz, Color LED Controller 2.4GHz, LED Controller 2.4GHz, Controller 2.4GHz
MR2 RF 6A 2 in 1 Mini Dimmable CCT LED Strip Controller
Mini Single Color LED Controller (2.4GHz) Model No.: MR2 Features Plug in and play and making installation easier 4096 levels smooth dimming, Min brightness 0.1% Dimming Range 0.1-100% One controller can be paired with 12 remote (Control distance 30m) Auto-forwarding: Automatically forward the remote control signal to another controller, making the remote control distance infinite Support do not disturb mode setting, Suitable for areas with frequent power outages to save electricity Supports "Tuya Smart" app control (2.4GHz gateway is needed) Support Alexa, Google Assistant, Yandex Alice (2.4GHz gateway is needed) Parameters Name: Mini 2 in 1 LED Controller (2.4GHz) Model No.: MR2 Input Voltage: DC12-24V Output Current: Max 6A Output Power: 72-144W Output Type: Constant Voltage Control Signal: 2.4GHz RF Control Distance: 30m IP Rate IP20 Working Temp. -10~40°C 78.4mm Dimming level Dimming Range Dimming Curve EMC Standard (EMC) 4096 levels 0.1%-100% Logarithmic ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-3 V2.1.1 Safety StandardLVD EN 61347-12015+A1: 2021 EN 61347-2-11: 2001+A1:2019 Radio Equipment RED ETSI EN 300 440 V2.2.1 Certification: CE, EMC, LVD, RED Warranty: 5 Years 11mm 22.3mm Connection Diagram Input: DC12V~24V V+ V- Single Color Mode Input: DC12V~24V V+ V- V+ V+ CW W WW Dual White Mode Application Diagram APP 4G / 5G WiFi Tuya Cloud Alexa / Google Router Gateway cWL-Box2 DC12~24V Model No.: FUT006 Remote Compatible with remote control (need to be purchased separately) Model No.: C1 C1 FUT006 FUT007 B1 / B1-B / T1 B2 / T2 K1 / K1-B K2 / K2-B K3 FUT087 FUT087-B S1-B / S1-W S1-G WL-Box2 Remote Control Instructions 1). Linking Code Instructions Power Controller Or SET Link/Unlink 1 2 Power off, then power on again after 10 seconds or the "SET" button once or turn on the light through the PUSH switch. Short press the "I" button 3 times within 3 seconds. 3 The light flashes slowly 3 times, indicating successful Linking. If the light does not flash slowly, the code binding failed, please perform the above steps again. (Note: Already coded lamps cannot be coded again). 2). Unlinking Code Instructions Method 1: Power Controller Or SET Link/Unlink 1 Power off, then power on again after 10 seconds or the "SET" button once or turn on the light through the PUSH switch. 2 Short press the "I" button 5 times within 3 seconds. 3 The lamp flashes 10 times quickly, indicating successful unlinking If the light does not flash quickly, unlinking failed, please perform the above steps again. (Note: For lamps that are not coded, no unlinking is required). Method 2: Press and hold the "SET" button for 5 seconds, the light flashes 10 times, and the code is cleared successfully. 3). Auto-forwarding Remote control signal auto-forwarding The remote control signal received by the controller will be forwarded to another controller within 30m, making the control distance infinite. Auto-forwarding Controller Distance 30m Controller 4). Turn Do Not Disturb mode on and off (ON by default) Turn on "Do Not Disturb" (applicable to areas with frequent power outages to save energy) Turn on Do Not Disturb mode: Short press the "OFF" button 3 times within 3 seconds, and then short press the "ON" button 3 times. The light flashes 4 times to indicate success. Note: When the lamp is powered on again after a power outage, its status (lights on or off ) will remain the same as before the power outage. Turn off Do Not Disturb mode: Short press the "ON" button 3 times within 3 seconds, and then short press the "OFF" button 3 times. The light flashes 4 times slowly to indicate successful shutdown. Note: When the lamp is powered on again after a power outage, its status will be on by default. 5). PWM high frequency / low frequency switching Switch to high frequency: Press "OFF" button 1 time within three seconds and press "ON" button 5 times, Activated successfully once led light flashes 2 times quickly. Switch to low frequency: Press "ON" button 1 time within three seconds and press "OFF" button 5 times, Activated successfully once led light flashes 2 times slowly. Notice 1. When installing the device, please turn off the power to ensure safety. 2. Please check if the input voltage is consistent with the device. 3. Non-professional users cannot disassemble the device directly, otherwise the device may be damaged. 4. Do not use the device near large metal areas or areas with strong electromagnetic waves, otherwise the remote control distance will be seriously affected. Made in ChinaAdobe PDF library 17.00