Redragon Griffin Pro 3 Modes Connection Gaming Mouse

Introduction

Dear user,

Thank you for choosing our Redragon product. To protect your rights and for better customer service, we ask that you note our warranty rules.

1. Within the guaranty period, repair is guaranteed for failure due to electrical circuit problems. Other damages, such as disassembly, hard impacts, submersion into water, plugging into improper current or voltage, and damage caused by natural disasters such as fire, flood, or earthquake are not included.

2. Consumable parts (such as foot pad) and spare parts replacement are not included in our warranty.

Button Instructions

The gaming mouse features the following buttons:

• 1. Left button
• 2. Right button
• 3. Scroll wheel (Click as middle button)
• 4. Side button, defaulted forward
• 5. Side button, defaulted backward
• 6. DPI + (default)
• 7. DPI - (default)
• 8. BT pairing button
• 9. Mode/Power switch

Visual description of the mouse layout: The top of the mouse shows buttons 1 (left), 2 (right), and 3 (scroll wheel). The left side features buttons 4 and 5. The top rear has buttons 6 and 7 for DPI adjustment. The bottom of the mouse has a switch labeled 9 for Mode/Power and a button labeled 8 for BT pairing.

Quick Start Guide

Wired Connection

Set the [2.4G/OFF/BT] switch to "OFF". Connect the mouse to your computer using the USB cable. The computer will automatically recognize and configure the mouse, and begin charging the battery.

2.4G Wireless Connection

1. Set the [2.4G/OFF/BT] switch to "2.4G".
2. Plug the USB receiver into a USB port on your computer. The computer will recognize and configure the mouse automatically.

Tip: If auto-connection is unsuccessful, or you want to connect to a new device, unplug the USB receiver, press and hold the [DPI+] button (6) and the [DPI-] button (7) simultaneously for 3 seconds. The LED will flash green. Plug the USB receiver into the computer's USB port, and the mouse will re-connect.

BT Connection

1. Set the [2.4G/OFF/BT] switch to "BT".
2. Press and hold the [BT pairing button] (8) for 3 seconds. The mouse will enter pairing status.

Turn on your PC's Bluetooth function and search for available devices. It will find the "BT5.1 Mouse" device. Select the device to pair. After pairing, you can start using the mouse.

Power Save Function

The mouse enters power save mode when it is inactive for over 2 minutes. Move the mouse or click any button to wake it up.

How to Recharge the Battery

1. Low Battery Warning: The scroll wheel LED will blink red when the battery is low.
2. Use the provided USB cable to connect to a PC USB port to charge the battery. The scroll wheel LED will remain solid red while charging. After the battery is fully charged, the LED will turn to the current DPI color.

Warning: Charging current: 5V = 2A max.

DPI Adjustment and Indication

Default DPI settings and their corresponding scroll wheel LED indicator colors (breathing effect):

• 1. RED: 800 DPI
• 2. BLUE: 1200 DPI
• 3. GREEN: 1600 DPI
• 4. CYAN: 2400 DPI
• 5. PURPLE: 4800 DPI

Report Rate Adjustment

The mouse supports adjustable report rates: 125Hz, 250Hz, 500Hz, 1000Hz. When the computer does not have the software installed, press and hold the scroll wheel button (3), then press the DPI+ button (6) to cycle through report rates. The LED will flash white to indicate the current report rate:

• 125Hz: LED flashes 1 time.
• 250Hz: LED flashes 2 times.
• 500Hz: LED flashes 3 times.
• 1000Hz: LED flashes 4 times.

When the computer has the software installed, you can use the mouse software to set the report rate.

Backlight Adjustment

Press and hold the scroll wheel button (3), then press the DPI+ button (6) to cycle through 6 defaulted backlight effects.

For more adjustable functions and macro recording, please download and install the mouse software to enable more possibilities.

Features a built-in Li-thion battery (1 unit).

FAQ

1. If the mouse is not responding: Please check if the mouse is plugged correctly into the corresponding computer USB port, or try another USB port.
2. If the mouse is moving slowly, jumping, or with delay: Please try using the mouse on another surface. Dark, dirty, un-flat, or bright surfaces may affect mouse performance. Using a mouse pad is strongly recommended.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Battery Safety Guidelines

• DO NOT replace the battery with a different model.
• DO NOT use this product if the battery shows signs of damage, including, but not limited to tearing, deformation, leakage, or the smell of electrolytic material.
• DO NOT touch the battery if material is leaking and seek immediate medical attention if any material comes into contact with your skin or eyes.
• DO NOT expose the battery to liquid, heat sources, electricity (outside of the product itself), or other non-standard operating conditions.
• DO NOT remove the battery except for proper disposal and recycling as required by local laws and regulations.
• DO NOT impact, bend, alter, disassemble, or otherwise damage the battery, as the contents are volatile, hazardous, and can be harmful.

CAUTION: Failing to follow all safety guidelines may result in product damage, explosion, fire, and/or electric shock.