Tribit XSound Go User Manual
Contents
- English User Manual
- 取扱説明書 (Japanese User Manual)
- Benutzerhandbuch (German User Manual)
- Manuale Utente (Italian User Manual)
- Guide Utilisateur (French User Manual)
- Manual de Usuario (Spanish User Manual)
Safety Instructions
- Avoid dropping.
- Do not disassemble.
- Avoid extreme temperatures.
- Do not use the device outdoors during thunderstorms.
- Do not use any corrosive cleaner/oil to clean.
Specification
- Bluetooth version: V5.0
- Support: A2DP, AVRCP, HFP, HSP
- Output power: 2 x 8W
- Battery: 3.7V, 4400mAh
- Battery charge time: 5 hours
- Input: DC5V/1A
- Dimension: 175 x 59 x 56 (mm)
- Weight: 380g
What's in the box
- Tribit XSound Go speaker
- USB-C Cable
- Lanyard
- User Manual
Overview buttons & Indicators
Indicator: Status light
Microphone: Built-in microphone
Power on/off button: Press to turn the device on or off.
Bluetooth button: Press to enter pairing mode.
Volume + button: Press to increase the volume level.
Volume - button: Press to decrease the volume level.
Play/Pause button:
- Press to play/pause music and answer/end calls.
- Long press to reject a call.
- Press twice to skip to the next track.
- Press three times to skip to the previous track.
Indicator Status
- Blue indicator flashes slowly: Reconnection mode
- Blue indicator flashes quickly: Bluetooth pairing mode
- Blue indicator keeps on: Pairing successful
- Red indicator flashes slowly: Low battery power (<15%), charge the speaker as required
- Red indicator flashes quickly: Very low battery power (<2%), the speaker will automatically power off after 5 seconds. Charge the speaker immediately.
Connections
AUX in: Connect to devices via 3.5mm audio cable.
Charging: Connect the USB-C cable to charge the speaker.
Bluetooth connection
- Turn on Bluetooth on your device.
- Press the Bluetooth button on the speaker to enter pairing mode.
- Select "Tribit XSound Go" from the list of available Bluetooth devices on your phone.
Stereo Mode
1. Make sure both speakers are on.
2. Press the Bluetooth button on one of the speakers to enter pairing state.
3. Press the Bluetooth button on the other speaker for 5s, then release the button to enter Stereo pairing when you hear the “Stereo mode” prompt. When you hear “Left channel” on the left speaker and “Right channel” on the right speaker, the “Stereo mode” is on.
Reset
If the speaker has a problem, press and hold the “Volume +” and “Volume –” buttons simultaneously for 5 seconds to reset the device. Then try pairing again (delete the old pairing from your device).
Customer Service
- 18-month limited warranty
- For FAQs and more information, please email to: support@tribitaudio.com
FCC Statement
This equipment complies with part 15 of the FCC Rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
* RF warning for Mobile device: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
