User Guide for SUNELL models including: SN-IPR80xxHCAA Active Detterence Turret Network Camera, SN-IPR80xxHCAA, Active Detterence Turret Network Camera, Detterence Turret Network Camera, Turret Network Camera, Network Camera, Camera
Sunell 5MP SN-IPR8050HCAA-B Active Detterence Camera
Sitemap - Shenzhen Sunell Technology Co., Ltd.
File Info : application/pdf, 2 Pages, 1.28MB
DocumentDocumentActive Deterrence Eyeball Network Camera Quick Setup Guide NO:101-400-0249-02 Issue:1.2 Precautions Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip "You have entered the area of electronic surveillance" in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries. It alerts you to moderate dangers which, if not WARNING avoided, may cause minor or moderate injuries. It alerts you to risks. Neglect of these risks may CAUTION cause device damage, data loss, device performance deterioration, or unpredictable results. NOTE It provides additional information. WARNING Y Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users' non-conformance to these requirements. Y Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged. Y Use accessories delivered with this device. The voltage must meet input voltage requirements for this device. Y If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out. Y When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device. Y Do not focus strong light (such as lighted bulbs or sunlight) on this device. Otherwise, the service life of the image sensor may be shortened. Y If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage. CAUTION Y Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart. Y Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks. Y Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device. Y Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device. Y Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment. Y Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation. Y If the device is installed outdoors, take insect- and moistureproof measures to avoid circuit board corrosion that can affect monitoring. Y Remove the power plug if the device is idle for a long time. Y Before unpacking, check whether the fragile sticker is damaged. If the fragile sticker is damaged, contact customer services or sales personnel. The manufacturer shall not be held responsible for any artificial damage of the fragile sticker. Special Announcement Y All complete products sold by the manufacturer are delivered along with nameplates, quick setup guide and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products. Y The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice. Y This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product, the final interpretation of company is as a standard. Y This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product. NOTE For more information, please refer to website. 1 Open Package Examination Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1-1 is consistent. Table 1-1 Packing list Component Quantity Remark Eyeball Network Camera 1 Quick Setup Guide 1 Accessory package 1 Location sticker 1 2 Device Structure 2.1 Device Ports NOTE Different devices may have different interfaces, multi-head cables, and fill lights; Please refer to the actual product. Figure 2-1 Hardware interfaces Reset button CVBS video out SD card slot Table 2-1 Hardware interfaces description ID Port Name 1 SD card slot Description Install a SD card. NOTE Y Before installing a SD card, make sure the card not in write protection state. Y Before removing the SD card. make sure the card not in write protection state. Otherwise, the data may be lost ,or the SD card may be damaged. 2 CVBS video out Output an analog video signal. You can connect the camera to a TV monitor through this interface to view the analog video. 3 Reset button Long press the reset button for 5s to restore the original settings. Fill light settings Camera's fill light has four modes, they are intelligent dual light ( current fill light will switch to warm light after an alarm is triggered, and will switch back to the original fill light for 30s after the alert is released.), warm light, infrared lamp and none (Close the fill light and the color of image will stay in previous mode). The different cameras can be set different fill light modes; Please set fill light modes according to the actual scene. Day mode: It can be used in the scene with sufficient ambient light for 24 hours, do not turn on the fill light, and the image is in color. Night mode: it can be used in the scene where there is insufficient ambient light for 24 hours, turn on the fill light (it can be selected according to the four modes of the fill light). Auto mode: Automatically switch the fill light mode according to the luminance of the environment. Timing mode: Set the start and end time of the day, this time period is day mode for camera. Figure2-2 Multi-head cable 1 1 2 Reset 3Some models may not have 23 94 94 Power Table 2-2 Multi-head cable description ID Core Description Remark Network 1 access interface Connects to a standard Ethernet cable or Support PoE. The green light is on, the network PoE connection is normal; The yellow light supply. flashes when the data is transmitted. Some models maybe not have the lights; Please refer to the actual product. 2 Power supply Connects to a 12V direct current (DC) (DC 12V) power supply. 3 Reset button Long press the reset button for 5s to restore the original settings. Figure 2-3 Multi-head cable 2 1 Po r t 2 3 4 Reset 5 Some models may not have IN G OUT G 6 Table 2-3 Multi-head cable 2 description ID Core Description 1 Network access interface Connect to a standard Ethernet cable or PoE. The green light is on, the network connection is normal; The yellow light flashes when the data is transmitted. Some models maybe not have the lights; Please refer to the actual product. 2 Audio output Connect to an external audio device such as a speaker. 3 Audio input port Receive an analog audio signal from devices such as a sound pickup device. 4 Power supply Connect to a 12V direct current (DC 12V) (DC) power supply. Remark Support PoE supply. Applied for camera with audio function 5 Reset button Long press the reset button for 5s Applied for to restore the original settings. some models 6 G Alarm output COM OUT Alarm output G Alarm input COM Applied for alarm function IN Alarm input 2.2 Camera Dimensions NOTE Different devices may have different dimensions; Please refer to the actual product. Figure 2-4 Dimensions Unit: mm 120.0° 120.0° 118 3-5 107 118 3 Device Installation Installation Steps: Step 1 Open the package, take out the camera, and disassemble camera's decorate cover, as shown in figure 3-1. Figure 3-1 Disassemble camera Step 2 Stick the installation location sticker on the ceiling or wall, drill three holes following the marks on the sticker. Push the plastic anchors into the holes, as shown in figure 3-2. Step 3 Correspond the camera to plastic anchors, fix it to the ceiling (or wall) by using self-tapping screws. Figure 3-2 Camera installation Cable out from the top Plastic anchors Self-tapping screws NOTE You can route cables from the top or from the side. If you use the top routing method, drill a hole in the installation surface first, as shown in figure 3-2. If you use the side routing method, please cut the compression ring outlet, and route the multi-head cable out from the side gap at the bottom of the camera. Step 4 Connected the multi-connector cable, the camera is connected to screen to adjust monitoring perspective, then tighten the decorate cover, as shown in figure 3-3. Figure 3-3 Finish installation NOTE The camera's monitoring angle can be adjusted by three-axis rotation: horizontal rotation, up and down rotation, axial rotation of the lens, adjust the direction of the camera and aim the lens at the target. 1 The hemisphere can rotate up and down range of 0 to 80°; 2 the hemisphere can rotate left and right range of 0 to 360° ; 3 The ball lining can rotate 360° left and right. 4 Quick Configuration(e.g IE) 4.1 Login Step 1 Open the Internet Explorer, enter the IP address of IP camera (default value: 192.168.0.120) in the address box, and press Enter. The login page is displayed as shown in figure 4-1 . Step 2 Input the user name and password. NOTE Y The default user name is admin. The default password is admin. Modify the password when you log into the system for first time to ensure system security. Y It is advised to restart the device three minutes later after modifying password to ensure modified successfully Y You can change the system display language on the login page. Figure 4-1 Login User Name Password English Step3 Click Login, the main page is displayed. 4.2 Modify IP address Choose Configuration > Device > Local Network, the Local Network page is displayed. Enter the IP address in the IP Address box and click Apply as shown in figure 4-2. After the IP address is set successfully, please use the new IP address to log in the Web interface. Figure 4-2 Local Network Local Network Network Card ID IP Protocol DHCP IP Address Subnet Mask Default Gateway Preferred DNS Server Alternate DNS Server MTU(1280-1500) 1 IPv4 192.168.0.120 255.255.255.0 192.168.0.1 192.168.0.1 192.168.0.2 1500 Refresh Apply 4.3 Browsing Video To ensure the real-time video can be played properly, you must perform the following operation when you log in the web for the first time: If user can access the web immediately, please ignore the steps of adding trusted sites. Step 1 the Internet Explorer. Choose Tools > Internet options > Security > Trusted sites > Sites, in the display dialog box, click Add, as shown in figure 4-3. Figure 4-3 Adding a trusted site http://192.168.0.120 A B Step 2 In the Internet Explorer, choose Tool > Internet Options > Security > Customer level, and set Download unsigned ActiveX control and initialize and script ActiveX controls not marked as safe for scripting under ActiveX controls and plug-ins to Enable, as shown in figure 4-4. Figure 4-4 Configuring ActiveX control and plug-in Step 3 Download and install the player control as prompted. NOTE If the repair tips displayed when installing the control, please ignore the prompt, and continue the installation, the login page is displayed when the control is loaded. To browse a real-time video, click Live Video. The Live Video page is displayed, as shown in figure 4-5. Figure 4-5 Live Video Live Video Playback Personnel Count 1 Configuration Note: ActiveX is being used to play live video now Switch to VLC, then play the video Switch to Plugin, then play the video Stream stream 1 2 1 Personnel Count: User can query the data of personnel count, through year, month, day. The statistics can be downloaded. The data can be shown by line chart, histogram, list. 2 AI Live video: Click the icon to view the snapshots of human face or license plate (click "Face" or "Plate" to switch ). The bottom page will show the captured images of vehicle and human . Figure 4-6 Installation of personnel count 15° Pedestrian direction CAUTION If user requires higher accuracy of personnel count, we recommend the user to install camera and draw the line following as figure 4-6. 4.4 Set Intelligent Analysis At "Configuration > Intelligent Analysis " interface to set the parameters of intelligent analysis (Perimeter, Single Virtual, Fence, Double Virtual Fences, Multi Loiter, Converse, Personnel Count), so that the user can receive the alarm of target, as shown in figure 4-7. Figure 4-7 Intelligent Analysis - Perimeter Perimeter Clear Enable Sensitivity Limit Target Type Output Channel Audio Detect Alarm Sound Alarm File Flashlight Alarm Alarm Record Sun Mon Tu e s Wed Thur Fri Sat Refresh Apply Table 4-1 Parameters of Intelligent Analysis Parameter Description Enable Enable the fence, draw the warning area at live video by using mouse. The default status is disable. Sensitivity The sensitivity of the retrieval target, choose from 1 to5, 5 means the highest sensitivity, it will detect the target easily. Limit Target Enable, the type can be chosen, person or car/ Type person/car. Output Channel Select to linkage camera's relay output channel for "Intelligent Analysis Alarm". Audio Detect Enable, user can choose the audio file to play if it Alarm happens alarm. The audio file can be set at " Configuration > Alarm > Sound Alarm Output "interface. Flashing Alarm Enable, when the device detect target, it will be flashing. Alarm Record Enable, if user set the parameters of email, it will send email to user if it happens Intelligent Analysis alarm. SMTP Enable, if user set the parameters of FTP, it will send snapshot to FTP server if it happens Intelligent Analysis alarm. FTP Upload Enable, if user set the parameters of FTP, it will send snapshot to FTP server if it happens Intelligent Analysis alarm. Schedule Set valid time for all above Intelligent Analysis settings. 4.5 AI Multi object At "Configuration > AI Multi object" interface, user can enable face detection, full body detection, vehicle detection, set the other parameters of detection, as shown in figure 4-8. Figure 4-8 AI Multi-object Face Detection Fullbody Detection Vehicle Detection Display Trace Info Show Detection Area Confidence Coefficient Face Pixel Min(30-300) Body Pixel Min(30-300) Body Pixel Min(30-300) Vehicle Pixel Min(30-300) Image Matting Quality Snapshot Mode Upload Image Interval(1-10s) FTP Upload Image Matting FTP Upload Whole Image Algorithms Library Version NOTE For better capture performance, it is recommended to use 6mm focus length lens or above.