Tyger Auto: Contact Us
Instruction Manual for TYGER models including: TG-LX3F82448 LanderX Running Board, TG-LX3F82448, LanderX Running Board, Running Board, Board
Tyger Auto LanderX Running Board Compatible with 2019-2023 Ford Ranger | Supercrew Cab | TG-LX3F82448 | Drop Step Side Step Rail Nerf Bars : Automotive
File Info : application/pdf, 4 Pages, 4.00MB
DocumentDocumentTYGER LanderX BEFORE INSTALLATION READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT TG-LX3F82448 TORQUE VALUES Fastener Size Class 8.8 Torque (ft-lbs) 6mm 6-7 8mm 15-16 10mm 31-32 12mm 54-55 14mm 87-88 Class 10.9 Torque (ft-lbs) 6-7 22-23 44-45 78-79 125-126 x1 Driver/Left TYGER LanderX x1 Passenger/Right TYGER LanderX x1 Driver/Left Front Mounting Bracket A x2 Driver/Left Center/Rear Mounting Brackets B x1 Passenger/Right Front Mounting Bracket C x2 Passenger/Right Center/Rear Mounting Brackets D x12 10-1.5mm x 25mm Hex Bolts x12 10mm Lock Washers x12 10mm x 27mm OD x 3mm Flat Washers x12 8mm x 25mm Combo Bolts Reference the letters printed on the brackets to determine mounting locations A Front B B Driver/Left TYGER LanderX D D Passenger/Right TYGER LanderX 1/4 Customer Support: www.tygerauto.com/contact C Front V230719 Bottom View ATTENTION: Refer to the D or P labelling on the tubes to determine the Driver or Passenger side steps. TYGER LanderX XX-D Driver/Left LanderX Front XX-P Front Passenger/Right LanderX PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. (2) 10mm x 25mm Hex Bolts (2) 10mm Lock Washers (2) 10mm Flat Washers STEP 1 Starting installation under the driver/left side inner rocker panel. Locate the threaded mounting holes in the rocker panel toward the front wheel opening (Fig 1). Remove the plastic plugs covering the mounting holes. Select the Driver/Left Front Mounting Bracket A (Fig 2). Attach Bracket to driver/left front location with (2) 10mm x 30mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers (Figs 2 & 3). DO NOT fully tighten hardware. Driver/left side Installation Pictured A Front (Fig 2) Driver/Left Front Mounting Bracket A installation Front (Fig 1) Driver/left front mounting location A Front (Fig 3) Driver/Left Front Mounting Bracket A attached 2/4 TYGER LanderX STEP 2 Move to the center of the vehicle and locate the threaded mounting holes (Fig 4). Select (1) Driver/Left Center/Rear Mounting Bracket B (Fig 5). Attach the Bracket to the threaded holes with the included (2) 10mm x 25mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers (Figs 5 & 6). DO NOT fully tighten hardware. Driver/left side Installation Pictured STEP 3 Move to the last threaded holes closest to the rear wheel opening (Fig7). Select the remaining Driver/Left Center/Rear Mounting Bracket B (Fig 5). Repeat STEP 2 to attach the Rear Mounting Bracket (Figs 5 & 8). DO NOT fully tighten hardware. Driver/left side Installation Pictured Front (Fig 4) Driver/left Center mounting location (4) 10mm x 25mm Hex Bolts (4) 10mm Lock Washers (4) 10mm Flat Washers B B (Fig 5) Driver/Left Center and Rear Mounting Bracket B installation Front Rear (Fig 7) Driver/left Rear mounting location B (Fig 8) Driver/left Rear Mounting Bracket B installed B Front (Fig 6) Driver/Left Center Mounting Bracket B installed STEP 4 Carefully unwrap the TYGER LanderX. Select the Driver/Left TYGER LanderX. Line up the TYGER LanderX with the (3) Mounting Brackets. Attach the TYGER LanderX to the Brackets with the included (6) 8mm x 25mm Combo Hex Bolts (Figs 9-13). 3/4 Driver/left side Installation Pictured (2) 8mm x 25mm Combo Hex Bolts A XX-D Front (Fig 9) Attach Driver/Left TYGER LanderX to Front Bracket TYGER LanderX (Fig 12) Driver/Left TYGER LanderX attached to Center Bracket B (Fig 10) Driver/Left LanderX attached to Front Bracket A (2) 8mm x 25mm Combo Hex Bolts (Fig 11) Attach Driver/Left TYGER LanderX to Center and Rear Brackets B (Fig 13) Driver/Left TYGER LanderX attached to Rear Bracket B STEP 5 Level and adjust the TYGER LanderX and tighten all hardware. STEP 6 Repeat STEPS 1-5 to install the Passenger/Right TYGER LanderX "P". STEP 7 Do periodic inspections to the installation to make sure that all hardware is secure and tight. 4/4