INMBSPAN1280000 Panasonic VRF to Modbus TCP Slave or to Home Automation Gateway

Order Code: INMBSPAN1280000

Installation Sheet rev.1.1

By HMS Industrial Networks S.L.U.

SAFETY INSTRUCTIONS

⚠️ WARNING

Follow carefully these safety and installation instructions. Improper work may lead to serious harm to health and may damage the Intesis gateway and/or other connected equipment.

The Intesis gateway must be installed by an accredited electrician or similar technical personnel, following all safety instructions and country legislation for electrical equipment installation.

The Intesis gateway cannot be installed outdoors or exposed to direct solar radiation, water, high relative humidity, or dust.

The Intesis gateway must only be installed in a restricted access location.

For wall mount, fix the Intesis device firmly on a non-vibrating surface. For DIN rail mount, fix the Intesis gateway properly to the DIN rail. Mounting on DIN rail inside a metallic cabinet properly connected to earth is recommended.

Always disconnect power from any wires before manipulating and connecting them to the Intesis device.

A power supply with an NEC Class 2 or Limited Power Source (LPS) and SELV rating must be used.

Always respect the polarity of power and communication cables when connecting them to the Intesis gateway.

Supply the correct voltage to power the Intesis gateway; refer to technical characteristics for voltage range details.

CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries according to instructions. Battery replacement shall be done by an authorized installer.

CAUTION: The device is to be connected only to networks without routing to the outside plant. All communication ports are considered for indoor use only and can be connected to SELV circuits only.

This device was designed for installation in an enclosure. To avoid electrostatic discharge in environments with static levels above 4 kV, precautions should be taken when the device is mounted outside an enclosure. When working inside an enclosure (e.g., making adjustments, setting switches), typical anti-static precautions should be observed before touching the unit.

Safety instructions in other languages can be found at: https://intesis.com/docs/manuals/v6-safety

CONFIGURATION

Use the Configuration Tool to configure the gateway.

See instructions to download and install the latest version at: https://intesis.com/docs/software/intesis-maps-installer

Use the Ethernet connection or the Console Port (mini USB type B connector) to establish communication between the gateway and the configuration tool.

Follow instructions in the user's manual for more details.

Owner's Record

The serial number is located at the rear of the gateway. Record this information in the space provided below. Refer to it whenever you contact your gateway dealer or support team regarding this product.

Serial No.: _________________________

INSTALLATION

Follow instructions to properly install the gateway.

Disconnect mains power supply before connecting it to the Intesis gateway. Disconnect power of any bus or communication cable before connecting it to the Intesis gateway.

Mount the Intesis device on the wall or DIN rail following the instructions below, respecting the safety instructions above.

Connect a NEC Class 2 or Limited Power Source (LPS) and SELV rated power supply to the Intesis device, respecting polarity for DC power or Line and Neutral for AC power. Apply a voltage within the admitted range and of sufficient power (see technical characteristics).

A circuit-breaker must be used before the power supply (Rating 250V-6A).

Connect the communication cables to the Intesis gateway; refer to the user's manual for details.

Power the Intesis gateway and the rest of the connected devices.

NOTE: The device cannot be installed in air-handling space.

Wall Mount

Separate the fixing clips in the bottom of the box by pushing them outwards until you hear a "click", indicating the clips are in position for wall mount.
Use the holes provided to fix the box to the wall using screws. Use the template below for wall hole placement.

Diagram Description: Shows the fixing clips in their original position (for DIN rail mount) and in the position for wall mount.

DIN Rail Mount

With the box clips in their original position, first insert the box into the upper edge of the DIN rail, then insert the box into the lower part of the rail using a small screwdriver, following the steps in the figure.

Diagram Description: Illustrates the process of mounting the device onto a DIN rail.

CONNECTIONS

Power Supply

Must use NEC Class 2 or Limited Power Source (LPS) and SELV rated power supply.

If using DC power supply: Respect polarity applied to terminals (+) and (-). Ensure the voltage applied is within the admitted range. The power supply can be connected to earth, but only through the negative terminal, never through the positive terminal.

If using AC power supply: Ensure the voltage applied is the admitted value (24 Vac). Do not connect any terminals of the AC power supply to earth, and ensure the same power supply is not supplying any other device.

Diagram Description: Illustrates power supply connections for DC and AC, showing terminals for positive/negative or line/neutral, and earth connection.

Ethernet / Modbus TCP / Home Automation / Console

Connect the cable from the IP network to the ETH connector of the gateway using an Ethernet CAT5 cable. If communicating through the building's LAN, contact the network administrator to ensure traffic on the used port is allowed through the LAN path (refer to the gateway user manual for more information).

Default IP is 192.168.100.246.

Diagram Description: Shows the Ethernet port (RJ45 connector) and associated LEDs for link and activity.

Port A / P-Link 1 Panasonic

Connect the P-Link terminals of the Panasonic Outdoor Unit to the connectors A3 and A4 of the gateway's Port A. No polarity needs to be respected.

Diagram Description: Shows Port A with screw terminals labeled A1, A2, A3, A4, and indicates the P-Link 1 connection.

Port B / P-Link 2 Panasonic

Connect the P-Link terminals of the Panasonic Outdoor Unit to the connectors B1 and B2 of the gateway's Port B. No polarity needs to be respected.

Diagram Description: Shows Port B with screw terminals labeled B1, B2, B3, and indicates the P-Link 2 connection.

Console Port

Connect a mini-type B USB cable from your computer to the gateway to allow communication between the Configuration Software and the gateway. Ethernet connection is also allowed. Check the user manual for more information.

Diagram Description: Shows the Console Port as a mini-type B USB connector.

USB

Connect a USB storage device (not an HDD) if required. Check the user manual for more information.

Diagram Description: Shows a USB Type-A port for storage devices.

ELECTRICAL & MECHANICAL FEATURES

Feature	Details
Enclosure	Plastic, type PC (UL 94 V-0). Net dimensions (d x w x h): 90x88x56 mm. Recommended space for installation (d x w x h): 130x100x100mm. Color: Light Grey, RAL 7035.
Mounting	Wall. DIN rail EN60715 TH35.
Terminal Wiring (for power supply and low-voltage signals)	Per terminal: solid wires or stranded wires (twisted or with ferrule). 1 core: 0.5mm²... 2.5mm². 2 cores: 0.5mm²... 1.5mm². 3 cores: not permitted. If cables are more than 3.05 meters long, Class 2 cable is required.
Power	1 x Plug-in screw terminal block (3 poles). 9 to 36VDC +/-10%, Max.: 140mA. 24VAC +/-10% 50-60Hz, Max.: 127mA. Recommended: 24VDC.
Ethernet	1 x Ethernet 10/100 Mbps RJ45. 2 x Ethernet LED: port link and activity.
Port A	1 x Plug-in screw terminal block orange (2 poles). 1500VDC isolation from other ports. Reserved for future use.
Switch A (SWA)	1 x DIP-Switch for PORTA configuration: Reserved for future use (leave OFF, default).
PORT B	1 x Serial EIA232 (SUB-D9 male connector). Reserved for future use.
PORT B (cont.)	1 x P-link 2 Plug-in screw terminal block (3 poles). 1500VDC isolation from other ports (except PORT B: EIA232).
Switch B (SWB)	1 x DIP-Switch for PORTB configuration: Reserved for future use (leave OFF, default).
Battery	Size: Coin 20mm x 3.2mm. Capacity: 3V / 225mAh. Type: Manganese Dioxide Lithium.
Console Port	Mini Type-B USB 2.0 compliant. 1500VDC isolation.
USB port (USB pen drive)	Type-A USB 2.0 compliant. Only for USB flash storage device. Power consumption limited to 150mA (HDD connection not allowed).
Push Button	Button A: Not used. Button B: Not used.
Operation Temperature	0°C to +60°C.
Operational Humidity	5 to 95%, no condensation.
Protection	IP20 (IEC60529).
LED Indicators	10 x Onboard LED indicators: 2 x Run (Power)/Error, 2 x Ethernet Link/Speed, 2 x Port A TX/RX, 2 x Port B TX/RX, 1 x Button A indicator, 1 x Button B indicator.

Diagram Description: Shows the physical dimensions of the device: approximately 100 mm height, 100 mm width, and 130 mm depth.

	INMBSMIT*C000 Modbus Server Installation Guide - HMS Networks Intesis Installation guide for the HMS Networks Intesis INMBSMIT*C000 Modbus Server, designed for Mitsubishi Centralized Controllers and Home Automation Gateways. Includes safety, installation, and connection details.
	Intesis M-Bus to Modbus TCP & RTU Server Gateway Datasheet Datasheet for the Intesis M-Bus to Modbus TCP & RTU Server Gateway (model INMBSMEB0200000). This device facilitates seamless integration between M-Bus devices and Modbus TCP/RTU systems, featuring support for multiple clients, automatic device discovery, and configuration via Intesis MAPS. Includes technical specifications, features, and certifications.
	Intesis Modbus Server OCPP Gateway User Manual User manual for the Intesis Modbus Server gateway, enabling integration of OCPP Charging Points into Modbus TCP or RTU systems and external OCPP Central Systems. Covers setup, configuration, and technical specifications.
	Intesis INMBSOCP*0100 Installation Guide Installation guide for the Intesis INMBSOCP*0100 gateway, providing safety instructions, mounting procedures for wall and DIN rail, configuration details, connection diagrams, and electrical/mechanical specifications.
	Intesis INBACPAN1280000 Panasonic VRF to BACnet IP Server Gateway Installation Guide Comprehensive installation guide for the Intesis INBACPAN1280000 gateway, designed to integrate Panasonic VRF systems with BACnet IP networks. Covers safety warnings, installation procedures for wall and DIN rail mounting, connection details, and technical specifications.
	Intesis KNX TP to Modbus TCP & RTU Server Application Gateway Intesis KNX TP to Modbus TCP & RTU Server Application gateway enables seamless integration between KNX devices and Modbus BMS or controllers, supporting up to 3000 KNX objects and multiple Modbus clients.
	Intesis IN485UNI001I100 Universal Gateway: BACnet MS/TP & Modbus RTU User Manual User manual for the Intesis IN485UNI001I100 Universal Gateway, enabling IR air conditioners to integrate with BACnet MS/TP and Modbus RTU building management systems. Covers installation, hardware, and protocol specifications.
	Intesis M-Bus to Modbus TCP Server Gateway User Manual This user manual provides detailed information on the Intesis M-Bus to Modbus TCP Server Gateway, covering its features, installation, configuration, technical specifications, and operation. It is designed for industrial automation applications integrating M-Bus devices into Modbus TCP systems.