iFi
GO pod Max
Thank you for purchasing this GO series pod. The GO pod Max is an Wearable HD Bluetooth DAC/headphone amp.
1. GO pod Max status indicator
| LED | Status |
|---|---|
| Charging: | Steady Red |
| Fully charged: | Light off |
| Awaiting connection: | Flashing Blue |
| Ready to pair: | Alternately flash Red and Blue |
| Successfully paired: | Light off |
| Factory Reset: | Steady Blue ≥3s. Alternately flash Red and Green (only operated within Gaia APP when in binaural working mode) |
2. Touch control area
Diagram showing the touch control areas on the GO pod Max earbuds.
- Play/Pause/Answer the call (Single tap)
- Reject/hang up (Double tap)
- Skip forward (Double tap)
- Skip back (Triple tap)
- Volume Up (Hold right, used when in binaural working mode, not available in monaural working mode) ⬆️
- Volume Down (Hold left, used when in binaural working mode, not available in monaural working mode) ⬇️
- Wake up voice assistant (Single tap then hold)
- Bluetooth Pairing (Hold left and right together for ≥ 2s) ?
- Power Reset (Hold left or right for ≥12s, release when steady blue light is on*)
Tip: The reboot function can be used when the GO pod Max is abnormal or dead.
Tip: To wake up your phone's voice assistant, Single tap then hold left or right for ≥2s the Touch control area.
3. Microphone
Built-in mic for hands-free calls when paired with your smartphone.
4. 5V/1A USB-C battery charge input
Diagram illustrating the USB-C charging port.
For charging only. Requires a 5V/1A and above Type-C charger.
5. 5V/1.5A Qi wireless charging battery charging input
Diagram showing the GO pod Max charging case on a wireless charger.
Use a 5V/1.5A and above Qi certified wireless charger.
6. Charging box LED for Battery Status
| LED | Status |
|---|---|
| 4/4 | > 75% |
| 3/4 | > 50% |
| 2/4 | > 25% |
| 1/4 | ≤ 25% |
*Battery LED will flash when it is charging and will go out when it is fully charged.
Bluetooth Pairing
When removed from the charging case, GO pod Max LED blinks blue as it automatically searches for a previously paired device. If a stored device is not found, it then automatically enters pairing mode with LED blinking blue and red.
To enter pairing mode manually, press the left and right touch area together for ≥ 2s until LED flashes red / blue.
The GO pod Max is able to store up to 8 paired Bluetooth devices. Manual reconnection may still be necessary.
Connecting to Bluetooth device
Turn on the phone's Bluetooth function, and select "GO pod Max" in your Bluetooth list.
GO pod Max Auto-connecting
The GO pod Max switch on and connect to each other automatically when taken out of the charging case. The GO pod Max will flash blue lights to indicate automatic interconnection. Once interconnection is successful, the GO pod Max L +R will alternately flash the red light and blue light.
Single-GO pod Max Mode
Removing the right or left GO pod Max from the charging case will automatically turn them on. Select "GO pod Max" (Left GO pod Max) or “GO pod Max” (Right GO pod Max) in the Bluetooth list to connect.
If the GO pod Max has not successfully connected to Bluetooth for more than 5 minutes, they will automatically shut down.
When the GO pod Max is placed back in the charging case, it automatically switches off and goes into charging. The binaural hanging steady red light is always on until fully charged and then goes out.
Do not leave the left and right GO pod Max too far apart when taking them out of the charging case for pairing. The recommended distance is no more than 15 CM.
Set up your Bluetooth connection using our iFi-Gaia APP
Diagram showing the iFi-Gaia app interface on a smartphone, with QR codes for download.
Scan the QR code to download the app. Available on the App Store, Get it on Google Play.
Please search for "GO pod MAX" within the Gaia app.
The Gaia app helps you to use all functions and settings of the headset, such as digital filters to adjust the sound and resetting of GO pod MAX.
Ear loops connected to the GO pod MAX touch control units
Diagram showing how to connect different ear loop types (0.78mm 2-pin, MMCX) to the GO pod MAX earbuds.
Three ear loop pairs are supplied: 0.78mm 2-pin, MMCX.
YouTube Video
Scan the QR code to view the official iFi audio GO pod MAX video on YouTube.
Cautions
- Avoid extreme heat, cold, and humidity.
- Avoid dropping or crushing the GO pod Max, stressing ear loops by rapid pulling or extreme force, or bending ear loops at sharp angles.
- If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
- If you experience regular discomfort while using this product, discontinue use and consult a physician.
Warning: Dry the GO pod Max completely before placing them in the charging case to avoid damaging the case.
Specifications
| Specification | Details |
|---|---|
| Bluetooth version: | Bluetooth 5.4™ |
| Codecs: | LDAC*, LHDC/HWA*, aptX Adaptive, aptX, AAC, SBC |
| Chipset: | Qualcomm QCC 5100 Series |
| Range: | 10 m |
| Auto impedance detection: | 16Ω/32Ω/64Ω/300Ω |
| SNR: | 32Ω ≥129dB (A) / 300Ω ≥132dB (A) |
| THD + N: | ≤0.002% (1kHz/32Ω) |
| Frequency response: | 10-20kHz(-3dB) LDAC |
| Battery: | Ear hood 180mAh + Charging box 1500mAh |
| Working hours: | Ear hood ~7h + Charging box ~30h |
| Charging time: | Ear hood ~1.5h + Charging box ~2h |
| Power System: | 5V/1A or 5V/2A Qi certified charger |
| Dimensions: Ear hood L/R | 43.5 x 16.4 x 9.5 mm (1.7" x 0.6" x 0.4") |
| Dimensions: Charging box | 116 x 76 x 49.5 mm (4.6" x 3" x 1.8") |
| Net weight: Ear hood L/R | 24.5g (0.42 oz) |
| Net weight: Charging box | 185g (4.44 oz) |
| Limited Warranty: | 12 months** |
*LDAC - 660k(stereo) 990k(mono), LHDC - 560(Stereo) 900k(mono)
**12 months typical or as permitted/required by local reseller laws.
***Specifications are subject to change without notice.
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
